Думаю для мастера не столько важно сколько запсасти стоят или инная вешь.. Для него самое главное это весь процес от проделаной работы до финиша.👍👍👍👍👍👍
Crazy restoration it's seems you raised the dead. The best restoration . It's takes lot of patience to this kind of restoration but you did it well salute thank for your video
To my utter shock and amazement, this repair is not nearly as worthless as it might appear at first glance. I decided to do some research, and found out that the shells of a drill like this are actually cheap, like under $20. Provided that the internal components are fine, it might be worth it. Major caveat, though, I was going by the pricing of a similar drill from Ryobi, and not this exact drill, but I'd reason the prices for parts are similar. The most expensive part is, unsurprisingly, the motor and circuit board. However, this guy had to replace the motor shaft, and Ryobi does not sell that separately from the rest of the motor, so I have no idea how much that could cost. That being said, I don't think this is a particularly good idea. Given this drill was in a house fire, the heat might have compromised some components, meaning it might up and fail in short order. But, if it was just a broken case, with no heat involved, that would be worth fixing, especially a higher end tool. This tool, on the other hand, seems to be a budget brand tool.
@@Maranello12374 Exactly. I'm glad that someone understands that it's not always about money. Some people enjoy the process and the satisfaction. They are also learning and improving with every restoration they do.
По началу когда увидел что перфоратор весь сгорел думал не стоит вообще его ремонтировать..Но потом когда увидел что электроника целая то подумал что стоит..Браво маэстро 👍👍👍👍
Honestamente esta restauracion fue muy costosa, se aprovecho muy poco de la herramienta anterior, hasta el rotor se reemplazo, solo fue por satisfaccion de terminar el trabajo y ver el taladro terminado, casi fue el ensamble de una maquina nueva sin nada extraordinario
Arguably. To my utter shock and amazement, drill shells are only like $20. So, this is a tool that retails for $150, approximately, and was purchased for $8 (Incidentally, who would sell something like this? I would think most people would just trash it, or give it away for free.) So, replacing the case and some other bits would be not all that expensive. That being said, given this drill was in a house fire, I'd hesitate to try fixing it, given the heat could have compromised components in a way that is not visually apparent. Especially since this is a budget brand tool, and would not cost that much to replace. So, this technically saves money, but not enough to be worth it. A higher end tool is far more likely to be worth it.
Videonun 17.13'teki kısmında görülen, darbeli matkabın ön kısmında bir çember şeklini alıp iç parçalara iki yerden bağlanan siyah kauçuk parça, estetik bir görünüm için mi bulunmakta yoksa işlevsel bir parça mı? Teşekkürler. :)
Целесообразность ремонта; 1-Являетесь ли вы владельцем склада новых запчастей такого агрегата? - Да. 2-Много ли у вас свободного времени? - Да. 3-Имеете ли вы прибыль с инет контента такого видео? - Да. Могу только порадоваться за вас, 3 из 3х... вам стоит заниматься такой херней.
I just wondered what they did with this? 😑 No matter how I think, I don't get any results! 🧐🫤 All in all, your work was excellent, because you were able to restore this so well. 😄
Думаю для мастера не столько важно сколько запсасти стоят или инная вешь..
Для него самое главное это весь процес от проделаной работы до финиша.👍👍👍👍👍👍
Praticamente fez uma Furadeira Nova!
Excelente Trabalho!
Brave man taken that repair on 😮
Crazy restoration it's seems you raised the dead. The best restoration . It's takes lot of patience to this kind of restoration but you did it well salute thank for your video
Thank you, thank you very much😀
With the cost of new ones, this amount of repair and spare parts needed I would not have bothered fixing it
Думаю для автора канала,главное не результат а процесс всей проделанной работы..
To my utter shock and amazement, this repair is not nearly as worthless as it might appear at first glance. I decided to do some research, and found out that the shells of a drill like this are actually cheap, like under $20. Provided that the internal components are fine, it might be worth it. Major caveat, though, I was going by the pricing of a similar drill from Ryobi, and not this exact drill, but I'd reason the prices for parts are similar. The most expensive part is, unsurprisingly, the motor and circuit board. However, this guy had to replace the motor shaft, and Ryobi does not sell that separately from the rest of the motor, so I have no idea how much that could cost. That being said, I don't think this is a particularly good idea. Given this drill was in a house fire, the heat might have compromised some components, meaning it might up and fail in short order. But, if it was just a broken case, with no heat involved, that would be worth fixing, especially a higher end tool. This tool, on the other hand, seems to be a budget brand tool.
things may change rapidly. skills like these are needed
@@Maranello12374 Exactly. I'm glad that someone understands that it's not always about money. Some people enjoy the process and the satisfaction. They are also learning and improving with every restoration they do.
No, I'm sure you wouldn't. However, for some people it's done for pleasure and the challenge. It doesn't have to be about money every time.
Parabéns pelo trabalho ,sou do Brasil.
Przepięknie jest to odrestaurowane pozdrawiam serdecznie. 👍👍👍👍👍👍
По началу когда увидел что перфоратор весь сгорел думал не стоит вообще его ремонтировать..Но потом когда увидел что электроника целая то подумал что стоит..Браво маэстро 👍👍👍👍
😇
the board with LEDs had to be tinned with acid flux first, then the LEDs had to be soldered
Very good video
Honestamente esta restauracion fue muy costosa, se aprovecho muy poco de la herramienta anterior, hasta el rotor se reemplazo, solo fue por satisfaccion de terminar el trabajo y ver el taladro terminado, casi fue el ensamble de una maquina nueva sin nada extraordinario
THANKIOUPR❤❤❤❤❤❤❤❤❤❤❤❤❤
Very good job 👍👍👍
Fico muito bom chou de bola muito top valeu
Good job broo 👍👍👍
Porque ela entrou em curto-circuito?
Nice work dude. Such a great restoration 👏👏
Ottimo lavoro
Apart from making the video for the channel, was the repair worth the cost?
Arguably. To my utter shock and amazement, drill shells are only like $20. So, this is a tool that retails for $150, approximately, and was purchased for $8 (Incidentally, who would sell something like this? I would think most people would just trash it, or give it away for free.)
So, replacing the case and some other bits would be not all that expensive. That being said, given this drill was in a house fire, I'd hesitate to try fixing it, given the heat could have compromised components in a way that is not visually apparent. Especially since this is a budget brand tool, and would not cost that much to replace. So, this technically saves money, but not enough to be worth it. A higher end tool is far more likely to be worth it.
Enjoyed the restoration 😊
I was surprised that the controller board was still good
Harus punya mesin pencetak benda plastik
Videonun 17.13'teki kısmında görülen, darbeli matkabın ön kısmında bir çember şeklini alıp iç parçalara iki yerden bağlanan siyah kauçuk parça, estetik bir görünüm için mi bulunmakta yoksa işlevsel bir parça mı? Teşekkürler. :)
The rubber ring acts as a seal to prevent the internal lubricating oil from being thrown out.
@@RefurbishmentKJ Bilgilendirme için teşekkür ederim. :)
You will break the ultrasonic cleaner with that amount of water in it. It's meant to be full of water/solution
Большой мастер😮
Excellent and accurate👍✌️👏👏👏👏
Why?
Wow 😮10/10 🎉🎉
good entertainment value
Less expensive buying a new one. But well done anyway
Restaurada furadeira de martelo rotativo (martelete)🔨😉
Good job ?? No. Great Job 👍 👍👍
superb
very good job amaizing
Thank you🤝🏻
Czy to się opłaciło naprawiać? Bardzo wątpię. Opłaciło się zarobić na kliknięciach
🤘🏻🤘🏻🤘🏻✌🏻✌🏻✌🏻✊🏻
good bro
nice job
Awesome
Целесообразность ремонта;
1-Являетесь ли вы владельцем склада новых запчастей такого агрегата? - Да.
2-Много ли у вас свободного времени? - Да.
3-Имеете ли вы прибыль с инет контента такого видео? - Да.
Могу только порадоваться за вас, 3 из 3х... вам стоит заниматься такой херней.
🇧🇩🇧🇩🇧🇩❤❤❤
think this as buying a new one but you also have to spend hours for it
이걸 살려내네 대단합니다
Only Fools and Horses. Triggers broom, totally original, only had two new heads and three new handles.😂😂
새거 삽니다
Achava melhor comprar uma noca😢
If ever I have see a fake video this is it 😂😂
Restoration can be save the cost
very well restore like and subscribe done
❤
👏👏👏👏👏👏💯💯💯💯💯👍👌🇧🇷🇧🇷
Круто 😊😊😊😊😊😊😊
Hobby :)
This was ridiculous he had to have lost a bet. Nothing was usable.
👌💯👍
Not really a repair as mainly new parts.
Bro giveaway bro
Quien compraría o repararía esa herramienta mediocre cuando puede comprarse una dewalt, una milwauke o una makita de ultima??
чисто байт на просмотры . отстой
I just wondered what they did with this? 😑 No matter how I think, I don't get any results! 🧐🫤 All in all, your work was excellent, because you were able to restore this so well. 😄
It suffered a fire🥹
Only Chinese CCP citizen will waste time to fix cheap brand name drill.