In his defense though guys, these bigger printers really do get a TON of vibration at almost any amount of acceleration. Even though they’re coreXY, on something this big, 3000 accel is something you’d have to use input shaper for to get the ringing to go away. I have a mercury one.1 built off an ender 5+ so I’m speaking from experience here
I was given a 1" thick pool table slate, and cut it into 24"x24" pieces. It works great as a poor man's surface plate for building, then as a printer platform.
@@WellHiddenTreasure Probably because you're using a different hotend? For sth like, 300mm/s you need a Rapido or other HF Hotend with a CHT Nozzle IIRC the maximum possible right now is a Rapido UHF with CHT Volcano, 400mm/s
@@tadhgd350 actually it does. It doesn't print faster than the full capabilities of a Voron, but it is a decent bit faster than the print speed in the video. If you need a list of the mods I run, if be happy to provide it 🙃
Yeah, the door latches should be used both on the top AND the bottom.
Door is shaking more than my diabetic grandma after falling into a pile of sugar
Rofl!!!
hahahhahahaha
😂😂😂😂
To stabilize it. Print a bracket that fits between your wall and the 3D Printer. Screw the bracket to the wall stud and Printer to bracket
In his defense though guys, these bigger printers really do get a TON of vibration at almost any amount of acceleration. Even though they’re coreXY, on something this big, 3000 accel is something you’d have to use input shaper for to get the ringing to go away. I have a mercury one.1 built off an ender 5+ so I’m speaking from experience here
What are your speed and accel settings?
I was given a 1" thick pool table slate, and cut it into 24"x24" pieces. It works great as a poor man's surface plate for building, then as a printer platform.
love how everything on the desk and current print is all hexagon
I would have just used cross strapping to help reduce the uneven shaking.
Dude how quiet is this thing!?
well the motors are inside the case so thats one thing :)
Nice! Which voron kit did you buy?
really doubt its reaching 300mm/s, I would bet the acceleration is limiting it.
Oh god, i want one
It's kinda slow. But still faster then what we got used to. Obviously not reaching the speeds.
Input shaper can add smoothness is you haven’t logged yet
What accelerations do you use?
That is not 300mm/s. Setting 300mm/s in the slicer is not the same as actually going 300. On those short distances it’s not reaching 300.
Much better 😉👍😀
Why is 300mm/s a valid measure? Why not flow mm3/sec or printing.?
Around 30mm3/s
@@mizz1414 that's great we could only up ours to like 24mm3/s (ABS) with bondtech direct and micro swiss. What are you using?
@@WellHiddenTreasure Probably because you're using a different hotend? For sth like, 300mm/s you need a Rapido or other HF Hotend with a CHT Nozzle
IIRC the maximum possible right now is a Rapido UHF with CHT Volcano, 400mm/s
@@mizz1414 not using a High Flow hotend, but using a CHT nozzle.
@@WellHiddenTreasure thats normal
Did you not seal the panels with foam tape?
What accelerations are you using?
It’s cookin
Wht kit did you use?
I like your enclosure... gonna do mine, the same way as yours :D
Very Very Good
There is no way this is going over 150 mm/a in this video
The acceleration?
5200mm/s
@@allyourtechai nice!
Sheesh! What’s the build volume?
@@danielmaxwell12 the voron 2.4 is 350x350x330mm according to specs.
@@sundog1973 This one yes, but not all. There's 250, 300, and 350. I have a 300.
Price
That is not 300mm/s
It's funny, I'm printing at 260mm/s and 4500 accel on a Cartesian and running marlin
Nitrogen floated air table.
maximum 100. not even close to 300
I love Vorons, but I will say you're leaving a lot of performance on the table. My Ender 3 prints faster than this lol
It does not
@@tadhgd350 actually it does. It doesn't print faster than the full capabilities of a Voron, but it is a decent bit faster than the print speed in the video.
If you need a list of the mods I run, if be happy to provide it 🙃
@@Lyrik8805 so it’s no longer an ender 3. That’s why I say it does not. Would have to at the very least install klipper and change the hotend
@@tadhgd350 technically it is still an Ender at it's core. No, it is *nowhere* near stock, but it is still technically an Ender
@@Lyrik8805 Mmmm just like my voron trident is still a voron - I call it “based off a trident”
6mm poly carbonate instead of that awful 3mm acrylic