Hi, do you need 2 separate jigs for say a bathroom mortise lock and an architectural mortise lock, or does 1 jig cover both? What size guide bush and cutter is required? How much is the jig to buy? Thanks Danny
Hi Danny, one jig will do all but you would need to change the lock type plates. You use a 12mm long reach cutter with either a 16mm guide bush(4mm spacer) or a 17mm guide bush(5mm spacer). Are you on Facebook? There are videos on setup and other vids. Look for B W Jigs
@@benweir8173 OK I'll give it a look. That's handy, 16mm guide bush 12mm cutter is the same set up for the hinge jig so saves all the faffing about switching stuff over👍
My apologies for the late reply, most Poe-le using these jigs use a 1/4“ router and they are fine with this jig. You wouldn’t be able to do the mortise with a 1/4” though. Even with a 1/2” router they don’t make a cutter long enough to do the full depth of the lock. Most use the Souber.
Have you used the trend lock jig? Just wondering how this compares to it.. could I use this with the set up I have for the hinge jig or would I have to change the router bit etc
Hi Ryan, I have tried the trend hinge jig. I bought it as soon as it came out. But I didn’t like the fact that it’s set out from the middle of the faceplate and not the spindle. Also all of the plates that are needed. This jig has the advantage of cutting the spindle, through holes and key hole types as well. Have a look on Facebook. There are some there that have them already and like them.
it's the same setup as the hinge jig, 12mm cutter and a 16mm guide bush. You could also use a 12mm cutter and a 17mm guide bush, just use a 5mm spacer instead of a 4mm spacer in setting up.
The jigs have a 32mm thrust pad housed into the jig on the inside that spreads the pressure. Quite a few users of the jig have worked on pre finished doors and haven’t had any problems.
Hi, the jigs are out of stock until the 22nd. They cost £415 + vat. They come with 3mm spacers, Euros and Bath Privacy plates. If you would like one send me your contact details to info@bw-jigs.com and I’ll send you a PayPal invoice. Delivery normally takes up to two days. Let me know if I can help further.
This jig is completely pointless since you have to do mortice with other tool anyway. If you are using this only for face plate you might as well use router with side fence and router bit sized same as width of plate. Not sure if this is sponsored or not but the price tag on this jig is an absolute joke
Hi Lukas, sorry you don't like the jig, not for everyone I suppose. but the jig doesn't only do the faceplate. it also does the spindle, through bolts and a range of different keyhole types like euro cylinders as well. Although you use something else to do the mortise there is still no quicker way. It takes a minuet to do the mortise and 3 mins to do the rest. ideal for price work.
Many have said this and I’m still waiting to set a video😂😂 I have seen some fit a lock in 6-7 mins using an mdf jig for a faceplate and drills for spindles and bath privacy’s for the finish looked like a rat had been chewing at it but I haven’t seen it done by hand in that time. Also where this jig comes into its own is on Euro cylinders.
You have passed the tap the lock in with the hammer handle test!
Nice job!
Just proves that when you have the right tools for the job!
Nice clean work👍
Man he is fucking bashing the lock with the hummer if you look close the lock got a dent the jig is good the operator rough
Great video, congratulations! Could I know where you found that corner cutter that you use to hammer the rectangular plates?
Hi, you can get them at Trend it’s known as a corner chisel. 👍
Fantastic jig fella. Hats off the effort and hard work on getting that engineered so well. Purchasing one now 👌
Pl
)
What a Great piece of kit - could save countless man hours.
What is the model of that jig? I looked on the website and didn’t see it there.
Hi Jane, that one was the prototype. It was the third one out of 6 before we had the final design.
Hi, do you need 2 separate jigs for say a bathroom mortise lock and an architectural mortise lock, or does 1 jig cover both? What size guide bush and cutter is required? How much is the jig to buy?
Thanks Danny
Hi Danny, one jig will do all but you would need to change the lock type plates. You use a 12mm long reach cutter with either a 16mm guide bush(4mm spacer) or a 17mm guide bush(5mm spacer). Are you on Facebook? There are videos on setup and other vids. Look for B W Jigs
@@benweir8173 OK I'll give it a look. That's handy, 16mm guide bush 12mm cutter is the same set up for the hinge jig so saves all the faffing about switching stuff over👍
Yes, I work on price work and don’t want to waste time changing cutters. Straight from the hinge jig, onto the lock jig.
@@benweir8173. Hi can you please give me some information how and where can I get and how much is thank you Bekim
@@bekimberisha1328 hi mate, I’m a new company and haven’t set up the website yet. But contact me on my email. Ben.O.Weir@gmail.com
Thats smart. I hate cutting locks in by hand, it just drags.
I take it a 1/4 inch router would struggle with this?
My apologies for the late reply, most Poe-le using these jigs use a 1/4“ router and they are fine with this jig. You wouldn’t be able to do the mortise with a 1/4” though. Even with a 1/2” router they don’t make a cutter long enough to do the full depth of the lock. Most use the Souber.
Have you used the trend lock jig? Just wondering how this compares to it.. could I use this with the set up I have for the hinge jig or would I have to change the router bit etc
Hi Ryan, I have tried the trend hinge jig. I bought it as soon as it came out. But I didn’t like the fact that it’s set out from the middle of the faceplate and not the spindle. Also all of the plates that are needed. This jig has the advantage of cutting the spindle, through holes and key hole types as well. Have a look on Facebook. There are some there that have them already and like them.
it's the same setup as the hinge jig, 12mm cutter and a 16mm guide bush. You could also use a 12mm cutter and a 17mm guide bush, just use a 5mm spacer instead of a 4mm spacer in setting up.
What brand is this and how to buy?
Hi the jig is from BW Jigs and you can get them at www.bw-jigs.com
Hi Ben , where can i buy the same jig in London?
Hi Eduard, this jig is one of the earlier prototypes. The finished jig is anodised black. You can get them at www.bw-jigs.com. 👍
@@benweir8173 Thank your so much 👍
The power of the rubber handled estwing! Jig isn't too shabby either!
😂😂best hammer for the job. 👍
how do they fare on pre finished oak veneered doors
The jigs have a 32mm thrust pad housed into the jig on the inside that spreads the pressure. Quite a few users of the jig have worked on pre finished doors and haven’t had any problems.
Добрый день как можно купит этот шаблон?
How was the whole for the lock body morticed out?
Try the Souber tools Morticer DBB
How you set up this jig for fire door?
Hi Jurek here’s a UA-cam video on the set up. ua-cam.com/video/ZtrBKVMlgYc/v-deo.html
What’s the machine called that cuts out the hole in the door ?
It’s EQ1010 festool router
TOO FAST, HOW MUCH DO YOU CHARGE FOR INSTALLATION?
It depends on the job. I’ve had as little as £3.50 years ago to £25 a lock more recently.
HOW MUCH IS THAT IN DOLLARS PLEASE.@@benweir8173
£500 per hour, not bad going👍
But having the best tools and experience makes all the difference.
@@altuspienaar7679 HI. WHAT BUSINESS ARE YOU MAKING THAT MUCH MONEY WITH?
Nice And clean work with this machine price please
Hi, the jig is £415 plus vat. You can join the Facebook group. It’s B W Jigs’s or you can purchase them at www.bw-jigs.com
Where can you get it?
Hi Dan, you can purchase the jigs at www.bw-jigs.com
@@benweir8173 👍
Hello,Where can I by this type of jig??
Hi, the jigs are out of stock until the 22nd. They cost £415 + vat. They come with 3mm spacers, Euros and Bath Privacy plates. If you would like one send me your contact details to info@bw-jigs.com and I’ll send you a PayPal invoice. Delivery normally takes up to two days. Let me know if I can help further.
Wow that's fast. I've never used one before.
Do you still drill out with flat bit or is the full depth routered as well?
Although you can use the jig for a mortise, they don’t make a cutter long enough. I use a Souber
3 min work = me having to using a hammer chisel and drill for 3 hours
Scary isn't it when you think a labourer can come along and achieve the same finish.
@@liammccormack7894 though you do need to have some skill with a router. It frees up time to do other jobs. 👍
Hi mate where did you get the jig from cheers
Hi Wayne you can contact me in info@bw-jigs.com thanks
Is this available yet?
Yes. Contact me in info@bw-jigs.com 👍
@@benweir8173 I will email you right now for info on this .
I had some questions on it as well I did just send a email on it
@@chicothesavage ive replyed via email. thank you.
What did you use to do the mortise with
I used the Souber for the mortise.
Nice work
I want one lol whats the price range
Hi Drew, they are £415 +vat. If you are on Facebook. Have a look for B W Jigs. There’s some videos on there on set up etc. Thanks.
Nice nickel plated lock forend … or was
Looks cool for runs of doors on site but for every day one off cutting in I’ll stick to sauber jig
Sure, it’s great for long runs. I don’t think I would use it for one. 👍
@@benweir8173 cuánto sale la plantilla de encastre de cerradura y como ce ac llega el güiro de $
WELDEN
VERY nice 👌 👍
interested in this mate
Hi mate, are you on Facebook? If you are, look up B W Jigs. There’s videos and and photos.
Dam I need this!!😃
Looks like a nice bit of kit, and a must if your 2nd fixing all day every day. Not the odd day here and there like me..
Hi Gavin, yes your right. If you have a good run then it is an investment. 👍
Hi bos itu jinis pahat apa?
Hi bos bagaimana sya mendapatkan barang ini
hai, biaya jig, £415 ditambah tambahan £75 untuk pengiriman di luar Inggris. jika anda tertarik beritahu saya.
Salam, Ben Weir
@@benweir8173 kalau jadi Ringgit Malaysia baerapa bos
@@muhammadagushariyanto5092 RM2 2654,54
ฉันชอบอุปกรณ์เจาะ❤❤❤😂
i love festool
Yes they are great tools and last as well.
Big on Festool. Looks like an expensive jig.
Yes they are expensive £415 + vat but it doesn’t take long to get your money back. 👍
Hihi I think you scratch this lock little bit 😉🤣🤣
شكرا
من دواعي سروري يا سيدي
Hamare address bata do hamen address Ham Le jaenge hamare se contact
Sorry, I don't understand
Базар жоқ
This jig is completely pointless since you have to do mortice with other tool anyway. If you are using this only for face plate you might as well use router with side fence and router bit sized same as width of plate. Not sure if this is sponsored or not but the price tag on this jig is an absolute joke
Hi Lukas, sorry you don't like the jig, not for everyone I suppose. but the jig doesn't only do the faceplate. it also does the spindle, through bolts and a range of different keyhole types like euro cylinders as well. Although you use something else to do the mortise there is still no quicker way. It takes a minuet to do the mortise and 3 mins to do the rest. ideal for price work.
Who cut the mortise it was not you.
Yes i cut the mortise with a Souber jig.
Алес гуд!❤
Nice jig but too expensive
Que buena macina como se puede arquerir me gusta
Yaaram earthquake machine chahie wali hamare ko bhi dilao kitne ki aati
Just slightly quicker lol
Many have said this and I’m still waiting to set a video😂😂 I have seen some fit a lock in 6-7 mins using an mdf jig for a faceplate and drills for spindles and bath privacy’s for the finish looked like a rat had been chewing at it but I haven’t seen it done by hand in that time. Also where this jig comes into its own is on Euro cylinders.
My FB "Jerzy tie", i have 5 time chiper ad with frame Lach jig,
O