Creality Ender-3 Max Neo - Overview & Bed Leveling
Вставка
- Опубліковано 5 жов 2024
- Creality Ender 3 Max Neo 3D Printer overview and bed leveling
Buy here: geni.us/oSzU
Recommended: geni.us/JustVlads
My main channel @Just Vlad
As an Amazon Associate I earn from qualifying purchases
Buy here: geni.us/oSzU
Recommended: geni.us/JustVlads
Just got my hands on one during the day it launched. Prints effectively right out of the box. I was perplexed and surprisingly impressed
Picking this up on Black Friday as my entry into 3D Printing. I appreciate the simple and easy instructions
Holy cow. Creality basically added all mods from thingiverse back into the printer. This thing is miles away from the Ender 3 pro I bought in 2019. Nicely done.
Still a Bowden, still a single 4010 fan for model cooling, still subpair screen, still suboptimal PSU placement...
The real upgrades are silent drivers (hopefully TMC2209 and not TMC2208), proper bed springs and bed insulation.
It is an oversized Ender 3 V2. And V2 is just a worse version of Pro...
Great overview. I'm planning to get this once it becomes available in my country.
Thanks! I was getting annoyed when the print kept failing.
cool, basically a normal ender 3 with upgrades
cheers a thousand times over man that was a mission
I do have a few questions though I had to redo my entire printer bed level but had completely forgotten how to do it so I watched your video but basically my questions are when I'm levelling the four corners do I need to have any drag/friction or do I only do it just as it is starting to get friction? Also I kind of had my z offset already set while levelling the four corners will that cause me any issues as after I did the auto levelling it needed to be adjusted to the offset that I have used since I got the printer which is -2.02
edit 2.0
I ended up doing it all over again with the offset on zero just to be sure I'm just hoping that the drag isn't just for the centre.
I turned on my printer after one day . But unlikely it's only showing red light in CR TOUCH. AND SCREEN IS SHOWING ONLY THR LOGO how the fix it pls need help in this.
can't be having a glass bed personally. started with an ender 3 v2 which came with a glass bed, ended up switching to pei which has been far better, and when i picked up an ender 2 pro as a secondary, it has a magnetic bed which id also rate much higher than the glass bed.
Agreed, PEI is best.
@@Just_Print going down the youtube rabbit hole, i've just seen a review of the ender 3 v2 neo and notice it comes with a magnetic built plate. seems odd they didnt keep conistency between the 2 🤣
@@Just_Print
When you are doing manual leveling what exactly are you doing with the paper are you adjusting the printer until the nozzle doesn't touch the paper or do you want to have the nozzle touching the paper and if yes how much I mean do you want it to cause a little fraction when you slide the paper under it or do you want the paper not touching it at all and able to move under the nozzle 100% freely without touching it at all?
Thank you very much ive watched many videos on how to do this but literally no one ever says anything about this so i am asking because i feel that this is something i need to know but no one has said what to do at all.
Thank you very much.
Nice overview. Disappointed they still can't enable level assist while compiling the firmware, it's 2022 after all.
its junk, waste of good money
@@roddsmith8954 what is good then>?
Will it fit the creality tent
Great stuff, sub'd!
Overall good video, but you really need to work on the terminology and nomenclature. The "heartbreak" you kept referring to is a "heatsink". There were also a lot of other terminology issues.
Keep up the good work you have a lot of potential!
Thanks for your comment. Will work on it.
he said heatbreak, but yeah its heatsink/heatbreak
I can’t make this thing print correctly.
I just got one of these. I do not understand how to level this thing. I already have a plain ender 3 with no auto leveling. So I know I can level a bed. But when I manually level, then try to auto level, then print, it's still printing way too far away from the bed. How can I fix this?
I went through this three time, about nine times I manually leveled it total, just for it to be printing too high.
Did you get this resolved? Min arrived today (still in the box) and in this vid he levels the bed, then sets the z-axis offset - see 10:04.
Did you try that step?
bed will be wrarped,these are a very bad printer altogether.
@@roddsmith8954 not really
When you are doing manual leveling what exactly are you doing with the paper are you adjusting the printer until the nozzle doesn't touch the paper or do you want to have the nozzle touching the paper and if yes how much I mean do you want it to cause a little fraction when you slide the paper under it or do you want the paper not touching it at all and able to move under the nozzle 100% freely without touching it at all?
Thank you very much ive watched many videos on how to do this but literally no one ever says anything about this so i am asking because i feel that this is something i need to know but no one has said what to do at all.
Thank you very much.
I am still figuring this printer out, but generally from my experience with the Ender 3 pro, you want some friction on the paper when sliding between the nozzle and the bedding.
This is my first ever printer, served me well and is printing amazing after properly calibrating it
And tips on calibration? Can't seem to level correctly after switching nozzles
@@SaimesierP honestly not the best guy to ask as I’m not good at it
Best I can say is make sure the nozzle is hot when you put it is as the metal can change size and make sure the bed is level with the screws either some paper then use auto levelling
@@deeznuts23yearsago that's what I've been trying but 🤷🏾♂️ . Might be a different issue as my prints have gaps
Bro I followed all the steps and it still is not level
i took my cr touch off and binned it,cant beat manual leveling.
I have a new Creality Ender 3 Max Neo. I’ve been printing successfully for about 2 weeks. Today, I did a short 2 hr print, then switched PLAs and started on a new print. Suddenly, when the printer attempts to home, it detects the plate, but then continues to go down and digs into the plate. Auto leveling does the same thing. I have no idea what is going on. I’ve tried adjusting the a offset way high, but that made no difference. Re-tightened some screws. No change. I’m posting a short video. Any ideas? ua-cam.com/users/shortsJR5Z86Z-YpA
Again. Creality stuck in itself.