You dont need to touch the exhaust at the manifold if its single exhaust. Also, there is no reason to remove the front shaft, the rear shaft will slide out when you pry off the differential donut shock ring with the centre bearing on it. Just remove the 13mm bolts that holds it on and get ready for one to break unless you heat it very well.
There is a company called JBX that makes center support bearings that you can clamp on without taking the driveshaft off. You have to cut the old bearing off tho, but the rest it’s very easy to install.
Hey guys, my mechanic said my support bearing is right out of my 2015 Dodge Challenger SXT and I have to buy a complete drive shaft assembly...do you have just the support bearing for my car so I can just replace this part??
Hello what about the that yoke bearing the u joint? how come it wasn't replaced with everything else? also I can't seem to find one for my 2008 chrys. 300 touring. thanks
Is the 300 youre working on a RWD or AWD model? Im from canada and this part on canadian part websites 934-301 is SAYING its for a AWD model and inorder to get one for a RWD you have to buy a whole drive shaft assembly..?
Bearing separator not needed. Wd40 and tapped a pry bar to remove the center bearing. Also front half of the driveshaft doesn't have to be removed left it installed into the transmission.
My 05 magnum makes a hopping/clunking sound only on takeoff. Could this be my culprit? I have checked everything else on the drivetrain. No codes or lights.
I need some help please. It was hard for me to separate the 2 piece drive shaft. I used a block of wood and a hammer to separate then bow im having an even harder time trying to put them back together. I didn't mark them when I removed them. Please help, what should I do to get them back together???
There is a little mark on the edge of one of the shafts. One of the splines is twice as wide, on the male end and you can find the female end with a matching wide spline to slide in.
+Jim Cordy We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
+CreoleIndianEagle The part in this video fits your application, and the install should be the same or similar. The ability to do it at home depends on your skill level and tools available to you.
@@1AAuto My level is still willing learn. Brakes, Wheel Assembly Hubs, Power Stering Pump, Alternator, Cold Air Intake that's all l've done. Maybe this would have been somewhat ambitious
I got 2004 Ford 150 4 by 4.....it only vibrates or shakes from when u press the gas to accelerate when take off.....does it mean it's going and go back soon ?
Hi, I was wondering if this might be the cause of a ticking noise coming from midway through my car? It’s an 06 rt Charger, but the charger and 300 are both on the lx body so I figured it’d be the same. The ticking starts once I go over 30 mph I had a mechanic listen to it and he says it the center bearing, but I just thought I’d get a second opinion before I buy a new one. The car doesn’t shake or vibrate, just makes the noise. Thanks.
+Ronicca Hall Thanks for watching! That could be the issue, but there could also be something else wrong with the vehicle. We recommend you have a reputable shop inspect the vehicle to get a proper diagnosis if you are unable to do so. 1aauto.com
Put your hand near under the center console where the floor board is. If its making a noise like rubber breaking or something is loose and you feel it right there where your hand is, then its that, might as well check the flex joints if they are still good since its gonna be off
+Jose Roche This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
I have a 2006 300 Srt8. I have a vibration from 45-75 mph. It vibrates under throttle and on highway. It vibrates the entire car. Feels like right under center console. I have 129000 miles on her. What do you guys think? Could this be the issue with the center bearing
exactly what my car is doing, 170xxx kms(105xxxmiles) vibrates around 80kph and free way speeds get bad, hear and feel it when on the throttle but nothing when i get off the gass. hoping its this centre bearing gonna change it out this weekend
Looked for a video for my car but there aren’t any out there . Here’s some info to hopefully help someone from making the same mistake I did. 2015 charger se awd rear drive shaft cannot be disassembled. You will have to replace the entire shaft. Between $ 1000-1400.
+Amire Wren You might want to start with checking the fluid level to see if it's up to the recommended level. If any of our viewers needs to make this repair we carry the support bearing shown in this video on our website. Here's a link to them www.1aauto.com/driveshaft-center-support-bearing-with-bracket/i/1adsh00038?UA-cam&CTA%20Comment&ATony
+kendra price It may be referred to as a bearing puller/separator. Your local auto parts store may have one you can rent or purchase. Hope this helps you out. 1aauto.com
No, it doesn't really matter because the drive shaft isn't balanced on the car, it's balanced separately off the vehicle, so realistically, it doesn't matter if you mark it or not or get it in the same spot, it's still balanced. If this was an old school drive shaft and you were replacing the front u joint so you were taking the front yolk off the driveshaft, then it is important to mark the yolk and the shaft and get them back together in the same orientation because when the driveshaft is balanced, they are balanced together as one unit, but like I said, in this case, it's really not important at all.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
This dudes voice rings in my ears whenever I do sweaty work on my car
You dont need to touch the exhaust at the manifold if its single exhaust. Also, there is no reason to remove the front shaft, the rear shaft will slide out when you pry off the differential donut shock ring with the centre bearing on it. Just remove the 13mm bolts that holds it on and get ready for one to break unless you heat it very well.
Well said, thank you, Jim.
You have the best how-to videos on UA-cam! Thank you so much for the clear instructions!
There is a company called JBX that makes center support bearings that you can clamp on without taking the driveshaft off. You have to cut the old bearing off tho, but the rest it’s very easy to install.
Great upload!
I just did this job and didn't have to remove the exhaust. It was all stock.
How long did it take you? I'm thinking of starting at 4:00 pm. Hope it doesn't get too dark.
Can this part cause a CLUNK noise when shifting from Park to Reverse if it’s worn out? Thank you!
Yes it can although it could also be the transmission
Sounds like a u joint noise? Just get under there and inspect all the components.
Hey guys, my mechanic said my support bearing is right out of my 2015 Dodge Challenger SXT and I have to buy a complete drive shaft assembly...do you have just the support bearing for my car so I can just replace this part??
Does the chrysler 200 driveshaft come apart like this one also?
Hello what about the that yoke bearing the u joint? how come it wasn't replaced with everything else? also I can't seem to find one for my 2008 chrys. 300 touring. thanks
Can the 16 chrysler 200s bearings be replaced? Does the driveshaft come apart
Is the 300 youre working on a RWD or AWD model? Im from canada and this part on canadian part websites 934-301 is SAYING its for a AWD model and inorder to get one for a RWD you have to buy a whole drive shaft assembly..?
How do you know if the transmission end is balanced if you're changing the transmission ?
Just did this today and it took one hr with a bit help
Is this part replaceable on 2016 300S??
Bearing separator not needed. Wd40 and tapped a pry bar to remove the center bearing. Also front half of the driveshaft doesn't have to be removed left it installed into the transmission.
+Chris Atkinson Thanks for the feedback!
Yup. But all 3 are worn out on mine so might as well
You are installing the car dual exhaust system back. left side heat shield is missing between muffler and fuel tank. Is it safe installation ?
My 05 magnum makes a hopping/clunking sound only on takeoff. Could this be my culprit? I have checked everything else on the drivetrain. No codes or lights.
+SkyGunner58203 Thanks for checking us out! 1AAuto.com
I need some help please. It was hard for me to separate the 2 piece drive shaft. I used a block of wood and a hammer to separate then bow im having an even harder time trying to put them back together. I didn't mark them when I removed them. Please help, what should I do to get them back together???
There is a little mark on the edge of one of the shafts. One of the splines is twice as wide, on the male end and you can find the female end with a matching wide spline to slide in.
@@steveperez6511 i cant find the matching spline on the female end,?
how do I know what size center bearing to get without having to rip my car apart?
Any link to the tool to separate it
You don’t have to undo the front part of the drive shaft from the transmission. As you can see it slides off the splines.
Grasias por el video. Nesesito un balero igual para mi craysler 300 2015
I found it quicker to replace the whole driveshaft with new bearing instead of doing it this way , but to each its own
Will this work on a 2016 dodge charger rtd rwd?
+Jim Cordy We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
I’m wondering the same thing, can this be done on a 2016 300S AWD?
Dodge this setup mimic a 2010 Charger R/T?... Can this be done at home?
+CreoleIndianEagle The part in this video fits your application, and the install should be the same or similar. The ability to do it at home depends on your skill level and tools available to you.
@@1AAuto My level is still willing learn. Brakes, Wheel Assembly Hubs, Power Stering Pump, Alternator, Cold Air Intake that's all l've done. Maybe this would have been somewhat ambitious
Great information I going to change mind myself
I got 2004 Ford 150 4 by 4.....it only vibrates or shakes from when u press the gas to accelerate when take off.....does it mean it's going and go back soon ?
U joints or carrier bearing
Hi, I was wondering if this might be the cause of a ticking noise coming from midway through my car? It’s an 06 rt Charger, but the charger and 300 are both on the lx body so I figured it’d be the same. The ticking starts once I go over 30 mph I had a mechanic listen to it and he says it the center bearing, but I just thought I’d get a second opinion before I buy a new one. The car doesn’t shake or vibrate, just makes the noise. Thanks.
My center bearing was destroyed by the time I took care of it. So was the rear coupler. Ticking turned into a jack hammer.
zombieno1 did you have to get the rear as well as the bearing when you replaced? I have a jack hammer now too...
when slowing down to a complete stop my chrysler 300 2012 will jerk as if putting it in park could this be the problem
+Ronicca Hall Thanks for watching! That could be the issue, but there could also be something else wrong with the vehicle. We recommend you have a reputable shop inspect the vehicle to get a proper diagnosis if you are unable to do so. 1aauto.com
So if the part is failing will vibration occur while driving?
Yes
Put your hand near under the center console where the floor board is. If its making a noise like rubber breaking or something is loose and you feel it right there where your hand is, then its that, might as well check the flex joints if they are still good since its gonna be off
Can these same steps be used on a 2007 pacifica??
+Jose Roche This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
I have a 2006 300 Srt8. I have a vibration from 45-75 mph. It vibrates under throttle and on highway. It vibrates the entire car. Feels like right under center console. I have 129000 miles on her. What do you guys think? Could this be the issue with the center bearing
My car has the same problem from 30-50 mph, its awd just like the one on the video, I did the same thing the video says, problem was solved.
Yo ?
exactly what my car is doing, 170xxx kms(105xxxmiles) vibrates around 80kph and free way speeds get bad, hear and feel it when on the throttle but nothing when i get off the gass. hoping its this centre bearing gonna change it out this weekend
Excellent video. Thanks!
+Ryan Hull Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Looked for a video for my car but there aren’t any out there . Here’s some info to hopefully help someone from making the same mistake I did. 2015 charger se awd rear drive shaft cannot be disassembled. You will have to replace the entire shaft. Between $ 1000-1400.
hey 1aauto I have a 04 Monte Carlo can u guys show how to fix the jerking of the transmission
+Amire Wren You might want to start with checking the fluid level to see if it's up to the recommended level. If any of our viewers needs to make this repair we carry the support bearing shown in this video on our website. Here's a link to them www.1aauto.com/driveshaft-center-support-bearing-with-bracket/i/1adsh00038?UA-cam&CTA%20Comment&ATony
So what happens if you can't get them together
Any idea where to get OEM bolts for the coupler? Looking for the part number.
+zombieno1 You may be able to purchase them from the dealer. Thanks for watching. 1aauto.com
What size t60?
Were do i get the tool kit to pop center bearing or what is the tool called?
+kendra price It may be referred to as a bearing puller/separator. Your local auto parts store may have one you can rent or purchase. Hope this helps you out. 1aauto.com
Hey can anyone tell me what the cable is on carrier bearing for a 08 ford exscape
In case you didn't find out already, it's a ground.
What size is that pipe?
its not a pipe, its a bong
What happens if you don't mark were the couplers mount? Will it affect the balance? And if so how do you correct it.
Francisco Saez you'll get vibration
Wondering how you would correct it as well
Francisco Saez Hi have u got any feedback ?
No, it doesn't really matter because the drive shaft isn't balanced on the car, it's balanced separately off the vehicle, so realistically, it doesn't matter if you mark it or not or get it in the same spot, it's still balanced. If this was an old school drive shaft and you were replacing the front u joint so you were taking the front yolk off the driveshaft, then it is important to mark the yolk and the shaft and get them back together in the same orientation because when the driveshaft is balanced, they are balanced together as one unit, but like I said, in this case, it's really not important at all.
No safety glasses on while looking up at all the rust coming down into your eyes?
usually, all your videos are great. Thank you. Jim
driveshaft bearing on 2016 300