Thanks for this. Very clear what to do. Seems frustratingly over-complicated to me beause of all the different parts involved. But that is the manifacturers fault, not yours. My old cars - 70's mini and mk 2 escort - the door panel was one part which you unclipped. Thank you for uploading.
WARNING! Do not remove the first two screws as shown in this video. Just loosen them, because they hold the window runners in place. These are the two at the bottom of the door card. Removing the speaker gets you access to the runner if needed
Man, you are my hero! Any tips for the back door panels? I must lubricare the parts that are locking the doors since they are working in the summer but not in the winter.
Thanks for uploading this video, it was really helpful on removing the door panel. Now the pain is fitting it back. The stupid design releases the 2 window guides when the 2 bottom screws are removed. The one guide you can fit it back by removing the speaker. The other guide? Took me 2 hours and a lot of attempts to fit it back... what was the designer thinking?
Great now my window guiders are lose. How do I fix that? The two first screws are holding them in place, but I can’t place them when my panel is closed. And when my panel is open I can’t put in the scews
cyb3r78 btw I opened my window a little bit that gives you maybe 2 or 3 cm room for the guiders. But be carefull, your guiders are lose and your window can go a little awry.
I know the comment is 3 years old, but anyone else who struggles, the trick is to remove the speaker. Through the speaker hole, put your arm and reach the rear window guider. Yes, you have plenty of space to do that. Put the long screw and with your hand align the guider. The front is obviously a bit easier as it's pretty visible without the speaker in place as well.
This video is completely the wrong way and will make refit nearly impossible. To do this correctly; - remove fabric covered panel - roll window down untill the bottom of the glass and glass clamps can be seen. - loosen glass clams using a torx driver ( do not undo all the way) - tape or wedge the glass in this position - roll the window mechanism down to half way (the window and mechanism are now Seperated) - Remove all the screws as shown in video, plus one additional screw in the top of the window runner / mechanism ( top of the runner further from hinge side) - lift panel upwards and slightly towards hinge side. - THE DOOR PANEL IS DESIGNED TO BE REMOVED WITH THE WINDOW MECHANISMS ATTACHED - not as shown in video.
Thank you for posting this. I was completely stuck. One thing I've learned for this is to read all the comments on a how-to video before starting the job.
I wouldn't say "most* of the time. The panel is often removed to fix a common lock issue. Or to remove broken glass if the window has been smashed. Or to strip the door for repair. Motor failure would be the only isolated scenario where the SEAT approved method wouldn't be applicable. Dan
After you remove the seven fixing bolts you have to lift the whole card upwards and pull outwards to release it from the hooked plastic lugs or you risk breakage. Also be careful of the nylon lever located in the lock mechanism, it needs to be slid out by moving the card to the left.
You are the BEST. Thanks from Spain your only 💪👌
Thanks for this. Very clear what to do.
Seems frustratingly over-complicated to me beause of all the different parts involved. But that is the manifacturers fault, not yours.
My old cars - 70's mini and mk 2 escort - the door panel was one part which you unclipped.
Thank you for uploading.
WARNING! Do not remove the first two screws as shown in this video. Just loosen them, because they hold the window runners in place. These are the two at the bottom of the door card. Removing the speaker gets you access to the runner if needed
If you just loosen them you won't be able to remove the panel?!
Too late for me. I have been struggling for 4 hours trying to assembly this fucking panel.
@@tonyneillaw No, but it may get the access you need
@@cds401 I know your pain
@@cds401 yup same these fucking things wont come to place
Man, you are my hero! Any tips for the back door panels? I must lubricare the parts that are locking the doors since they are working in the summer but not in the winter.
Would this be same method for rear doors?
Is this for 1p facelift model from 2010?
Thanks for uploading this video, it was really helpful on removing the door panel. Now the pain is fitting it back. The stupid design releases the 2 window guides when the 2 bottom screws are removed. The one guide you can fit it back by removing the speaker. The other guide? Took me 2 hours and a lot of attempts to fit it back... what was the designer thinking?
Great now my window guiders are lose. How do I fix that? The two first screws are holding them in place, but I can’t place them when my panel is closed. And when my panel is open I can’t put in the scews
therealnashcarp exactly the same problem here:(
I fixed it, just by a lot of trying and patience. I am gonna bring it to the garage and pay €200,- for a new lock. Thats way less problems 😂
cyb3r78 btw I opened my window a little bit that gives you maybe 2 or 3 cm room for the guiders. But be carefull, your guiders are lose and your window can go a little awry.
I messed it all up. Thankfully service fixed it for me free of charge :)
I know the comment is 3 years old, but anyone else who struggles, the trick is to remove the speaker. Through the speaker hole, put your arm and reach the rear window guider. Yes, you have plenty of space to do that. Put the long screw and with your hand align the guider. The front is obviously a bit easier as it's pretty visible without the speaker in place as well.
Que tipo de destornillador es el primero que usas? What type screwdriver do you use on first etage?
torx 27
Is it enough only remove the door panel to change the complete door mirror?
This video is completely the wrong way and will make refit nearly impossible. To do this correctly;
- remove fabric covered panel
- roll window down untill the bottom of the glass and glass clamps can be seen.
- loosen glass clams using a torx driver ( do not undo all the way)
- tape or wedge the glass in this position
- roll the window mechanism down to half way (the window and mechanism are now Seperated)
- Remove all the screws as shown in video, plus one additional screw in the top of the window runner / mechanism ( top of the runner further from hinge side)
- lift panel upwards and slightly towards hinge side.
- THE DOOR PANEL IS DESIGNED TO BE REMOVED WITH THE WINDOW MECHANISMS ATTACHED - not as shown in video.
Thank you for posting this. I was completely stuck. One thing I've learned for this is to read all the comments on a how-to video before starting the job.
Wish I read this 1st. Only issue I got is the window dont work hence the reason for removing the panel
This only applies if the window is operational. Most of the times you go through this procedure because it does not work.
I wouldn't say "most* of the time. The panel is often removed to fix a common lock issue. Or to remove broken glass if the window has been smashed. Or to strip the door for repair. Motor failure would be the only isolated scenario where the SEAT approved method wouldn't be applicable.
Dan
is the rear door the same way to remove ?? i have a tweeter that isn't functioning like it should
No, unfortunately the window mechanism is connected to the door card and is a complete PITA to remove.
Buenas noches los altavoces para cambiarlos son los tornillos plateados k medida se puede poner, la misma medidas, sin quede el cristal al bajarlo
After you remove the seven fixing bolts you have to lift the whole card upwards and pull outwards to release it from the hooked plastic lugs or you risk breakage. Also be careful of the nylon lever located in the lock mechanism, it needs to be slid out by moving the card to the left.
A
Thanks for this comment, i was stuck there :p i just hope i won't have to remove the glass to get acces to side rearview
lol just did this now i cant but the door card back on
to replace the tweeters how should I do?
Did u find a way to replace the tweeters without taking of the door card?
How to take the door card off incorrectly.
and thats why i love seat .. its acctualy screwed together not just clips
matic šorn dumbass
I lost my remote inside car seat lion how can open the car
Thanks!
is it a leon 1p?
Yes
Thank you bro
Bestia !
Pordonde yeba. Elseguro depuerta
Nie lubie, bo jak ucina to urywa jeden zaczep na 100% nie polecam!!!