Been installing and a tech for 20 years plus . Good vid well explained and will help a lot of guys . Done a lot of the swing to slider conversions and pretty much like you do .
you are a God sent my man. i watch all your videos . i cannot tell you how much i have learnt and continue to learn from your channel . THANK YOU THANK YOU THANK YOU , so very much ,
Dankie dat jy die tyd gevat het om die hele installeering op te neem, verduidelik en op youTube te sit. Ek sal defnitief hierdie gebruik om my installeering te doen. Op die internet het al geleer om nie te kritiseer nie, omdat mense die werk GEDOEN het. En baie goed wat ek al gekyk het sal ek nooit aan pak nie. Maar ek wil net graag die volgende sê:" As n Boilermaker/fabricator, wanneer ek na die sweis werk skrik ek. Ek hoop dat jy by nou al baie beter kan sweis met n Arc Welder. n Arc Welder is self nie een van my sterk punte nie. Maar n enkel fase MIG Welder (hier by ons nouem hule dit inkorrek n "CO2 welder". Weet nie hoekom nie, want CO2 gasse word nie gebruik nie. Maar in elk geval.....) sal jou kwaliteit werk net soveel beter maak" Soos ek sê, ek kritiseer nie, dit is maar net n opinie. Weereens dankie vir die video.
Been uneasy advertising the Smart to my clients, been happy with Evo as I install it in three hours all by myself. But your explicit demonstration has boosted my confidence and would like to thank you. Just another question, been using lip channel instead of angle iron for railing, which one is the strongest?
According to the manual (www.centsys.co.za/pdf/PROD/SMART/Centurion%20Systems%20D5-Smart%20installation%20manual.pdf) ... 7.2. Retro-fit Installations (existing sites) The D5 SMART has been designed to retro-fit into most existing D3, D5 or D5-Evo installations, with the following provisions; * If the unit is installed with the gate in the closed position and the unit on the left-hand side (from the inside of the property), the rack should extend at least 75mm past the centre line of the existing pinion * If the existing unit is mounted with the maximum clearance to the foundation plate, the new unit will require that the rack be re-adjusted to obtain the correct mesh between the rack and pinion, as the existing bolts will be too short If the existing foundation plate is in a good condition, it is not necessary to replace it with the D5 SMART Foundation Plate. ****** However, ****** if the existing foundation plate is corroded or needs to be replaced for whatever reason, the D5 SMART foundation plate can accommodate the existing footprint without the need to re-route cable conduits.
This by far the best DIY guide ever. You can instruct the dead yo walk again.
thank you!
Great video. Thank you very helpful 🙏🏻👍
This is well elaborated and I am happy that u don't leave anything out thank u sir
Been installing and a tech for 20 years plus .
Good vid well explained and will help a lot of guys .
Done a lot of the swing to slider conversions and pretty much like you do .
thank you
I'm comparing this with the V2- Ayros and Somfy. What do you think
Thank you Philip for all your videos it really helps a lot - really appreciate it
Great video. Well explained. Nice visuals. Great audio. Well done. Got all my tools, just scared of welding.
Welding is easier than that levelling and measurements ! For me
Thanks for the video and sharing your knowledge with us public thanks you
you are a God sent my man. i watch all your videos . i cannot tell you how much i have learnt and continue to learn from your channel . THANK YOU THANK YOU THANK YOU , so very much ,
Thank you this was so informative. All in one full training
good information
Wow! Excellent video. Thanks a million.
The Best tutorial video ever❤❤❤❤
Great input! Thank you
Thanks. Perfect guides. Thanks again!!
Hi, as usual, awesome video. You should get your self some skateboard knee pads instead of a cushion.they work wonders for comfort while kneeling.
Thanks for the tip!
true what i also noticed
The D Smart series are the 👌 best
Wow. An extremely excellent and helpful video.
excellent video, explained well, thanks
Beautiful piece of innovation...smart series
Well explained... Awesome
Excellent video
This is an swesome video!
Good I learning more to you
Hello Ing
Please from the power supply coming to the gate one needs to obviously have a DB box before connecting to the earth bar am I right?
Fantastic video
Can I open my gate remotely even if I am away from the country
Excellent
How different is the base plate of the D5 Evo from that of the D5 Smart, I would like to replace the D5 Evo but do not wish to move the plate?
Good video thx
Good job thanks you sir
Is the angle iron rail solid for any gate
Thank you
How or where can I get those spaces used for setting the gear Rack
Awesome a
Best video
thanks
Dankie dat jy die tyd gevat het om die hele installeering op te neem, verduidelik en op youTube te sit. Ek sal defnitief hierdie gebruik om my installeering te doen.
Op die internet het al geleer om nie te kritiseer nie, omdat mense die werk GEDOEN het. En baie goed wat ek al gekyk het sal ek nooit aan pak nie. Maar ek wil net graag die volgende sê:" As n Boilermaker/fabricator, wanneer ek na die sweis werk skrik ek. Ek hoop dat jy by nou al baie beter kan sweis met n Arc Welder. n Arc Welder is self nie een van my sterk punte nie. Maar n enkel fase MIG Welder (hier by ons nouem hule dit inkorrek n "CO2 welder". Weet nie hoekom nie, want CO2 gasse word nie gebruik nie. Maar in elk geval.....) sal jou kwaliteit werk net soveel beter maak"
Soos ek sê, ek kritiseer nie, dit is maar net n opinie. Weereens dankie vir die video.
thank you, my welder is very old and i would like to change the method of my welding.
@@ecologicaltime I would like to order Centurion D5 motor online. What is the link to your online store?
Hello well explain! Could you please show us how to connect a gate motor Flash light to the D5 Smart ???
Been uneasy advertising the Smart to my clients, been happy with Evo as I install it in three hours all by myself. But your explicit demonstration has boosted my confidence and would like to thank you.
Just another question, been using lip channel instead of angle iron for railing, which one is the strongest?
thanks. In terms of the lip channel, i am not sure which is stronger as now there are rollers that are shaped for both round and angle.
Have you ever installed the raz racks? They are failing me
this guy is a life saver , i was struggling with a few alarm and cctv settings . he came to my rescue .
How did you remove the pinion spider
Excellent video. How do I activate auto closing?
thank you, pls use the app to set auto close.
Hi, my d5 smart not accept define limits, on screem show LOST. Need help please. Tks.
❤
Can a D5 Smart fit onto a current D5 base plate or will the D5 plate have to be removed and the D5 Smart plate installed?
According to the manual (www.centsys.co.za/pdf/PROD/SMART/Centurion%20Systems%20D5-Smart%20installation%20manual.pdf) ...
7.2. Retro-fit Installations (existing sites)
The D5 SMART has been designed to retro-fit into most existing D3, D5 or D5-Evo installations, with the following provisions;
* If the unit is installed with the gate in the closed position and the unit on the left-hand side (from the inside of the property), the rack should extend at least 75mm past the centre line of the existing pinion
* If the existing unit is mounted with the maximum clearance to the foundation plate, the new unit will require that the rack be re-adjusted to obtain the correct mesh between the rack and pinion, as the existing bolts will be too short
If the existing foundation plate is in a good condition, it is not necessary to replace it with the D5 SMART Foundation Plate. ****** However, ****** if the existing foundation plate is corroded or needs to be replaced for whatever reason, the D5 SMART foundation plate can accommodate the existing footprint without the need to re-route cable conduits.
No need the old base plate will work for any centurion motor no need to install new d5 smart plate it will fit existing d5 base plate no problem
No need change base it will wirk for d5 to d5 smart becos both use same bsse plate
Is this arc welding
why dont u work at centurion supoort to me ur 120% best teacher
thank you
Is it possible to add a courtesy light to this gate motor?
yes definitely.
👍🏼
Do you need to take building course to lay the concrete foundation
No
@@ecologicaltime I’ve done the d5 evo training at centurion but haven’t learnt the concrete foundation for the gate rail
What depth is the concrete foundation for the gate rail
Hi
Where is your business based?
thanks! great car and good engine, strong naturally aspirated engine, the new ones are running very hot, needs twice as much maintenance!
Good video but the welding quality - Hmmmmm...
thanks, yip you caught me, my weakness
Kindly sent me the Lagos address Nigeria
The inserted words covers most of you video
? do you mean subtitles?
Self explanatory 0
Excellent