Thanks for an easy to follow video with proper light and camera angles. My cable came off this afternoon and door fell of the track on one side. With your video as a refresher lesson I made quick work of it. You sir just gave me my memorial day off back to spend it how It should be, honoring the fallen, not fixing garage doors. 🇺🇸
Thanks for the video. This helped as my cable jumped off the spool today. Saw a couple of other videos, but yours was the easiest explanation. Fixed it without breaking a sweat.
Great vid and explanation on repairing this issue. How the heck does this even happen in the first place? I have a motor driven opener. All it does is lift and lower. We don't mess with the door in any other way, so I'm curious of causes in order to hopefully avoid this in the future. Thanks!
In my case, if the door tips to one side or the other even a little bit, it causes the cable to be loose for just long enough to pop off. I agree, I have no idea why it would do that being pulled from the center by an opener, but it obviously does 🤔 It may have to do with the length of the door. Ours is 18' wide (12' tall).
Hi Mojo, well you made that look easy good job we had 10c- yesterday today it's not that much better as we are at 6c- Sunday its shooting back up to 11c yippee. 🥵♨️🔥
Sorry for the late reply Larry! We had a family emergency the past week, and I was taking care of that. Unfortunately the weather forecast here is pretty bad for at least the next ten days. We have three -7℉ (-22℃) days in a row this week, and two of them have 23 mph winds! That comes to -33℉ (- 36℃) with the wind chill! We try not to even go anywhere in that kind of weather as you can get frostbite in just a few minutes on exposed skin. We also have about 6" of snow coming at the same time - just a miserable week as far as weather goes. It's going to be slow going around here probably thru the end of the year! 😑🥶🥶
Towards the end of the video you showed the spring stops you were going to install. I tried looking for the video but couldn’t find it. Do you have a link or title to the video? Also a link to purchase the spring track stops. I think these are exactly what my door needs.
It would have been easier to loosen the set screws on the drum. Then turn the drum to wind the cable on it making sure to stay in grooves. Then retighten the set screws on the drum to snug plus 1/2 turn then add 1/4 turn to each set screw.
Help! I used the pliers to hold the door at the highest point, loosened the set screws, and wound it up and reattached to the door (both sides), but when I finished the 2nd side, it completely unwound itself when I let go even though everything was back to normal. What am I missing?
Im trying to replace my cable on one side but I can’t seem to access the cable on one side to take it out I nearly ripped off my finger when the tension bar went off
You need to only work on the cable when door is in the up position without tension on the cable. There should be little to no tension on the cable when door is open.
It is a bit late, but for other viewers... As isaw on another video and my wire that gone off. As one wire still has tension on it, it keep the door, spring and drum where it should be.
Adjust spools on each side to place just enough tension to keep cable lightly taught at the closest point to pulling bracket end. Remember, door should be in up position before working on cables.
I'm sorry, but if you fed the cable end BEHIND the torsion bar, you would not have to go through the trouble of pulling/dropping/pulling/dropping the cable onto the drum.
You can find the pusher springs here: Garage Door Pusher Springs - Pair - amzn.to/4dHg2Zf
Thanks for an easy to follow video with proper light and camera angles. My cable came off this afternoon and door fell of the track on one side. With your video as a refresher lesson I made quick work of it. You sir just gave me my memorial day off back to spend it how It should be, honoring the fallen, not fixing garage doors. 🇺🇸
You're quite welcome Brandon! 😊
Thanks for the video. This helped as my cable jumped off the spool today. Saw a couple of other videos, but yours was the easiest explanation. Fixed it without breaking a sweat.
Glad I could be of help Ed! 😊
My cable came off my garage door at midnight…I came in and watched a couple of videos, and was able to fix it within 5 mins. Thanks you SO much!!
You're quite welcome Suzanne All bad things happen at midnight 🥴 Glad you got it fixed!
Thanks for doing this video. Probably seems simple to some but I had no idea how to fix the cable that came loose. Thanks again!
You're welcome!
Thanks for the help.The cable came off and I was able to fix it within 10 minutes 👍
You're quite welcome Carson 😊
Looks like your on Alaska! Nice!!
Thank you Gabriela 😊
just fixed mine right now. life saver video, thank you
You are quite welcome Michael! 😊
When you mentioned clamping rail and not missing tracks... now you talking my language 🤣 excellent job today my friend. 😊👍❤️
Thanks Dave! I'm the same way with woodworking lingo. When I hear a word, my ears perk right up! 😊
Thanks your video helped us tremendously 😊😊
You are quite welcome Tee! 😊
I like your outdoor buggy!!
Thanks again Gabriela 😊
Nice fix Mojo!
Exactly what I needed. Thanks!
You are quite welcome! 😊
Never done that, but it's nice to know how!
Great vid and explanation on repairing this issue. How the heck does this even happen in the first place? I have a motor driven opener. All it does is lift and lower. We don't mess with the door in any other way, so I'm curious of causes in order to hopefully avoid this in the future. Thanks!
In my case, if the door tips to one side or the other even a little bit, it causes the cable to be loose for just long enough to pop off. I agree, I have no idea why it would do that being pulled from the center by an opener, but it obviously does 🤔 It may have to do with the length of the door. Ours is 18' wide (12' tall).
Hi Mojo, well you made that look easy good job we had 10c- yesterday today it's not that much better as we are at 6c- Sunday its shooting back up to 11c yippee. 🥵♨️🔥
Sorry for the late reply Larry! We had a family emergency the past week, and I was taking care of that. Unfortunately the weather forecast here is pretty bad for at least the next ten days. We have three -7℉ (-22℃) days in a row this week, and two of them have 23 mph winds! That comes to -33℉ (- 36℃) with the wind chill! We try not to even go anywhere in that kind of weather as you can get frostbite in just a few minutes on exposed skin. We also have about 6" of snow coming at the same time - just a miserable week as far as weather goes. It's going to be slow going around here probably thru the end of the year! 😑🥶🥶
@@PlanetMojo it's fine just stay warm that is the main priority
Thanks mojo
You're welcome!
Thank you, short informative and to the point. I appreciate you.
You are quite welcome Abyss33!
Towards the end of the video you showed the spring stops you were going to install. I tried looking for the video but couldn’t find it.
Do you have a link or title to the video?
Also a link to purchase the spring track stops. I think these are exactly what my door needs.
Sorry Jack, my bad! Garage Door Pusher Springs - Pair - amzn.to/4dHg2Zf
Thank you Sir. Much appreciated. 🙂👍
Thank you! that's exactly what I needed to know.
Thank you Senior Trekker! 😊
If you’ve never worked on cables or springs before be very careful. You could very easily hurt yourself if you’re not sure what you’re doing.
Great information watching from jamaica
Thanks Marlon!
U r welcome
Interesting method
Thank you so much!
You're welcome! 😊
thank you lots!
You're welcome!
THANK YOU!!!!!
You are quite welcome!
Helpful😀
Thank you Tj Masters! 😊
It would have been easier to loosen the set screws on the drum. Then turn the drum to wind the cable on it making sure to stay in grooves. Then retighten the set screws on the drum to snug plus 1/2 turn then add 1/4 turn to each set screw.
You have to mark the drum location with the rod, have more tools, and spend more time…sounds harder to me.
Yea, that sounds easy.
Help! I used the pliers to hold the door at the highest point, loosened the set screws, and wound it up and reattached to the door (both sides), but when I finished the 2nd side, it completely unwound itself when I let go even though everything was back to normal. What am I missing?
Both of my cables comes off, what way is better to set back them with the door open or shut,?
From most videos I've seen, manually open the door. Disengage the red handle from the chain.
It's probably too late but you should have gone to videos on setting the springs on spring assembly like adding new or broken spring.
Door closed.
Okay great
@@frankorosz901…you are dangerous
Im trying to replace my cable on one side but I can’t seem to access the cable on one side to take it out I nearly ripped off my finger when the tension bar went off
You need to have someone come out and look at it then.
You need to only work on the cable when door is in the up position without tension on the cable. There should be little to no tension on the cable when door is open.
Use come alongs on booth sides
The springs need to have tension while you are doing that ? !
It is a bit late, but for other viewers...
As isaw on another video and my wire that gone off.
As one wire still has tension on it, it keep the door, spring and drum where it should be.
Mine keep coming off track as soon as I move the door. There is no tension
You likely need the spring tightened.
Adjust spools on each side to place just enough tension to keep cable lightly taught at the closest point to pulling bracket end. Remember, door should be in up position before working on cables.
Only the first track makes the difference. The rest will "spool" upon lowering and raising the door.
Did you hear yourself? Doing it your way would allow less final length in the cable causing the unequal movement…again.
I'm sorry, but if you fed the cable end BEHIND the torsion bar, you would not have to go through the trouble of pulling/dropping/pulling/dropping the cable onto the drum.
If and when this happens to you…you’ll find out your method will never work
Nomás tienes la voz gruesa pero no entendí nada.