Hi i have a 4 wire fire detector i bought from the same seller of the alarm it has settings to do it normally close or normally open, do you now what settings i need to do it please? Thanks in advance
I want to check that each PIR censer is working and what number it is without setting off the siren and receiving a text and phone call each time I trigger a PIR censer? Is this possible?
Hey Pajo, I've checked the original M2B alarm manual, for specific solar siren you are talking about (iGET SECURITY P12) and translated the procedure for you. It's bit tricky, but hope you can make it. 1) Enter the settings (default 8888 #). 2) Now enter 411#, then enter [43]+[A]+[#], A indicates the number 90 ~ 92. 3) Now enter *# to exit the settings. 4) Press the 'Code' button on the siren for 2 seconds, the two LEDs on the right will flash and then the two LEDs on the left remain lit. 5) Now it's a siren ready for pairing. 6) Press the 'lock' symbol on the enclosed 'alarm keychain' and then press 'unlock' 7) The siren light will flash. 8) Now you need to end the pairing on the siren, hold down the 'Code' button for 3 seconds, the siren will flash one more time.
Hi Scott. Unfortunately I don't know a way how to disable this informative sound, I know exactly what you mean. The only way how to make this arm/disarm informative sound less louder is by disconnecting siren itself.
Dobrý deň.Ďakujem za skvelý tutoriál. Konečne jasne vysvetlené nastavenie.Mohli by ste mi prosím poradiť ako zapnúť pípanie sirény pri stlačení zamknutého zámku na diaľkovom ovládači?
Dobrý den, všechno co popisujete je běžně dostupné v uživatelském manuálu. Mě by zajímalo, jak změnit obsah sms, které alarm odesílá např. při poplachu. Nějak jednoduše to musí jít. Alarm se prodává v různých jazykových mutacích a servisní piny zezadu jsou vyvedené. Veškeré audiohlášky jsem si modifikoval, stačilo se podívat do datasheetu použitého GSM modemu. Bohužel SMS jsou uloženy v řídícím procesoru a ten je navíc posílá GSM modemu v PDU módu. Nevíte jak na to?
What will happen If I put time to automatically turn on the alarm and one day I go on vacation. System will be locked all the time? Or alarm timer will unlock my system? Also, how can I setup to automatically turn on and off alarm only for specific alarm zones (sensors)?
Hello. Now that's a good question, but unfortunately I haven't tried the Timer in this way, just setting only 'Timer for daily Arm setup' - so, you should better try it and let me know :) I would say, that if you will in 'Defense zone programming' set to a specific sensor an option [4] bypas, then it shouldn't be activated during the Timer - but also in this case, I'm just guessing
@@morneo3 I made an alarm to turn on every night at midnight and turn off at 7 am. If I go on vacation alarm will be deactivated the first morning at 7 am which is not a good option. Is it possible to make a different schedule for specific days in a week?
Hi Bill. Like you know, the alarm is correctly set to ON mode by the genuine sound it will make. If this is not what you've been asking, please describe it to me in another words.
Hello. Unfortunately I'm not aware, that is possible to change the central unit language - it's not in the manual. This alarm doesn't have any app, for commands you are using just SMS
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."
I cant seemed to get the internal siren working, i tried to input the code 751# but when i armed it and tried to open one of the window the lcd will only highlight the alarm and will show the bell on top right corner, but no sound please help. Thanks
Hello. Please take a look, if you correctly connected wires of the siren. If yes, and the siren still doesn't work, please play my video from 4:39, where I'm explaining defense zone programming - here you can set per every sensor, if you want siren to go ON, or not
@@morneo3 thank you so much, but im referring to the internal unit siren or alarm, i tried to wired the red sired but its too loud, so i thought i just use the internal siren, that has much lower volume.
@@morneo3 im sorry i misunderstood, but you mentioned about correctly connecting the wires of the siren, isnt that for actual physical siren that sounding so loud? Im referring to the alarm within the unit that doesnt require any wiring, correct me if im wrong please, thank you.
@@maddie5 Now I see what you mean. What you described in your first comment is correct behavior. If you don't have connected physical internal siren, or the external one, the alarm will just show the bell and will contact you over the sms and call you, but it wouldn't make any siren sound from the central unit
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."
Hello, do you mean 'disarm' button on the remote or on the central unit? Because if you want to disarm on central unit, you need to enter your 'operation password' and # (default: 1234#). On the other hand on the remote, you will disarm only by pressing the button.
@@morneo3 I mean the disarm button on the control unit. I also have an older black gsm alarm, with no disarm button, which you disarm with the code (nnnn#) which is as you describe and makes sense. But on this newer white unit, it seems that Mr Burglar just has to press 'disarm' on the keypad.
@@markdransfield9520 Like the truth is, you can just turn off the control unit with the switch on the back. But if you will hide this central unit, there is no chance for burglar to find it and turn it off let's say in 10 seconds interval after triggering the alarm. Because once I did all the settings, I don't really need the central unit on a visible place - I'm just arming and disarming via the remote.
@@morneo3 I agree that hiding it is the best option: having it upstairs rather than just inside the front door. This can also help get stronger GSM reception, which I think these units are not great at.
The only thing left i can't figure out is delaying how long it will wait before going into alarm mode after opening front door (say if i forgot to disarm from phone) I've tried in setting mode (60)+(93(wired zone 1))+(2)+(4)+(1)+(#). This only seems to disable the zone 1 from going into alarm at all.
Добрый день подскажите пожалуйста у меня стоит на двери датчик открывания но срабатывает он только при повторном при первом открытии дверей не срабатывает при повторном открытии срабатывает сигнализацию, как это исправить?
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."
Thanks for support.
Good job. Can I ask you how to connect wire magnetic sensor? not wireless. Thank you
Nice video! does the system tell you when the AC is off and is not getting power via the cables anymore?
Thanks. Yes, it does, but only when it's armed.
@@morneo3 good to hear, I purchased it! thank you for your video ;)
@@Crus0e Hope, it will serve well. You are welcome :)
@@morneo3 you did a better job explaining how it works than AliExpress itself
Good one
Thank you
Hi i have a 4 wire fire detector i bought from the same seller of the alarm it has settings to do it normally close or normally open, do you now what settings i need to do it please?
Thanks in advance
Does the system notify you by text or call if triggered, even if the siren is not connected or off?
Hi there. Sure, it does, even without connected siren.
It's like a silent alarm - during event, you will recieve a call and after that also a SMS
@@morneo3 thank you so much, I appreciate it.
Do you have a manual with all the setup codes ?
Yes, I have a paperback version. But you could try this one, I've found: manualzz.com/doc/55736981/iget-security-m2b-owner-manual
@@morneo3 thats wonderful! Thanks :)
My siren doesn't call what could be the problem
Hi. You should turn it on in settings. Try to go accordingly with video in 11:57
Hi, it activates itself at 01.05 and in the morning 07.50. How can I solve this problem? how can I deactivate. Thanks for your help
You could try to turn off the 'timer' function:
ua-cam.com/video/iTFNnRTnd_A/v-deo.htmlsi=0LSt32vCloCI9w-2&t=401
I want to check that each PIR censer is working and what number it is without setting off the siren and receiving a text and phone call each time I trigger a PIR censer? Is this possible?
I see. Unfortunately this kind of test isn't possible, as far as I know from the alarm manual.
ماهي وظائف مداخل الانترنت في الجهاز؟؟؟
Do you now how do I configure solar siren ?
I can't make it
Hey Pajo, I've checked the original M2B alarm manual, for specific solar siren you are talking about (iGET SECURITY P12) and translated the procedure for you. It's bit tricky, but hope you can make it.
1) Enter the settings (default 8888 #).
2) Now enter 411#, then enter [43]+[A]+[#], A indicates the number 90 ~ 92.
3) Now enter *# to exit the settings.
4) Press the 'Code' button on the siren for 2 seconds, the two LEDs on the right will flash and then the two LEDs on the left remain lit.
5) Now it's a siren ready for pairing.
6) Press the 'lock' symbol on the enclosed 'alarm keychain' and then press 'unlock'
7) The siren light will flash.
8) Now you need to end the pairing on the siren, hold down the 'Code' button for 3 seconds, the siren will flash one more time.
Hello friend I've tried several ways and I don't think the problem is the system that emits to the siren
@@Pajo80if the mentioned procedure doesn't work, I would try to change the solar siren, as it could be malfunctioned
How do I stop the siren from bleeping everytime I arm or disarm the system?
Hi Scott. Unfortunately I don't know a way how to disable this informative sound, I know exactly what you mean.
The only way how to make this arm/disarm informative sound less louder is by disconnecting siren itself.
Hi! How can I rename sensor name as you did?
Unfortunately I don't know. I have a non-English names from the factory, as this product language mutation was dedicated to Czech and Slovak market.
Dobrý deň.Ďakujem za skvelý tutoriál. Konečne jasne vysvetlené nastavenie.Mohli by ste mi prosím poradiť ako zapnúť pípanie sirény pri stlačení zamknutého zámku na diaľkovom ovládači?
Napisem rovno dany kod, ktory sa zadava v settings alarmu pre aktivaciu kratkeho pipnutia sireny pocas arm/disarm:
751#
Dobrý den, všechno co popisujete je běžně dostupné v uživatelském manuálu. Mě by zajímalo, jak změnit obsah sms, které alarm odesílá např. při poplachu. Nějak jednoduše to musí jít. Alarm se prodává v různých jazykových mutacích a servisní piny zezadu jsou vyvedené. Veškeré audiohlášky jsem si modifikoval, stačilo se podívat do datasheetu použitého GSM modemu. Bohužel SMS jsou uloženy v řídícím procesoru a ten je navíc posílá GSM modemu v PDU módu. Nevíte jak na to?
Dobry den, ano presne ako pisete, vsetko je v podstate v manuale. Ale to co popisujete je uz velmi pokrocila vec na mna, nikdy som to neriesil.
What will happen If I put time to automatically turn on the alarm and one day I go on vacation. System will be locked all the time? Or alarm timer will unlock my system?
Also, how can I setup to automatically turn on and off alarm only for specific alarm zones (sensors)?
Hello. Now that's a good question, but unfortunately I haven't tried the Timer in this way, just setting only 'Timer for daily Arm setup' - so, you should better try it and let me know :)
I would say, that if you will in 'Defense zone programming' set to a specific sensor an option [4] bypas, then it shouldn't be activated during the Timer - but also in this case, I'm just guessing
@@morneo3 I made an alarm to turn on every night at midnight and turn off at 7 am. If I go on vacation alarm will be deactivated the first morning at 7 am which is not a good option. Is it possible to make a different schedule for specific days in a week?
@@weblist9009 Unfortunately it's not possible to make a custom schedule, only one time for ARM and one time for DISARM
Is it possible to do a walk test to check that everything is working without setting of the alarm each time it is triggered?
Hi Bill. Like you know, the alarm is correctly set to ON mode by the genuine sound it will make. If this is not what you've been asking, please describe it to me in another words.
Do u know how to lower the volume on the disarm and arm sounds
Unfortunately it's not possible, as far I know from the manual handbook.
Stick a sound deading Tab
Can I add more sensors to my alarm system?
Hi Loren. Yes, you can add several sensors of same type - for example you could have 5 PIR motion detection sensors
Okay thank you very much
Can i change the language from main unit? it is in Spanish, and what app for android i must intstall? thanks!
Hello. Unfortunately I'm not aware, that is possible to change the central unit language - it's not in the manual.
This alarm doesn't have any app, for commands you are using just SMS
How can I factory reset this device?
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."
I cant seemed to get the internal siren working, i tried to input the code 751# but when i armed it and tried to open one of the window the lcd will only highlight the alarm and will show the bell on top right corner, but no sound please help. Thanks
Hello. Please take a look, if you correctly connected wires of the siren. If yes, and the siren still doesn't work, please play my video from 4:39, where I'm explaining defense zone programming - here you can set per every sensor, if you want siren to go ON, or not
@@morneo3 thank you so much, but im referring to the internal unit siren or alarm, i tried to wired the red sired but its too loud, so i thought i just use the internal siren, that has much lower volume.
@@maddie5 my previous comment applies to internal siren - I don't even have the big external one
@@morneo3 im sorry i misunderstood, but you mentioned about correctly connecting the wires of the siren, isnt that for actual physical siren that sounding so loud? Im referring to the alarm within the unit that doesnt require any wiring, correct me if im wrong please, thank you.
@@maddie5 Now I see what you mean. What you described in your first comment is correct behavior.
If you don't have connected physical internal siren, or the external one, the alarm will just show the bell and will contact you over the sms and call you, but it wouldn't make any siren sound from the central unit
How Do I RESET the ALARM
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."
Thanks so much I will definitely try this Code...I have a D1D9 Alarm I bought on Amazon and this Code was Not in my Manual
how can I change the time from 40 seconds to less time on a door contact?
You need to check this part of the video - ua-cam.com/video/iTFNnRTnd_A/v-deo.html
The 'Disarm' button seems to disarm, with one press! No code needed! This seems crazy. Is the unit set up wrong?
Hello, do you mean 'disarm' button on the remote or on the central unit? Because if you want to disarm on central unit, you need to enter your 'operation password' and # (default: 1234#). On the other hand on the remote, you will disarm only by pressing the button.
@@morneo3 I mean the disarm button on the control unit. I also have an older black gsm alarm, with no disarm button, which you disarm with the code (nnnn#) which is as you describe and makes sense.
But on this newer white unit, it seems that Mr Burglar just has to press 'disarm' on the keypad.
@@markdransfield9520 Like the truth is, you can just turn off the control unit with the switch on the back. But if you will hide this central unit, there is no chance for burglar to find it and turn it off let's say in 10 seconds interval after triggering the alarm. Because once I did all the settings, I don't really need the central unit on a visible place - I'm just arming and disarming via the remote.
@@morneo3 I agree that hiding it is the best option: having it upstairs rather than just inside the front door. This can also help get stronger GSM reception, which I think these units are not great at.
The only thing left i can't figure out is delaying how long it will wait before going into alarm mode after opening front door (say if i forgot to disarm from phone) I've tried in setting mode (60)+(93(wired zone 1))+(2)+(4)+(1)+(#). This only seems to disable the zone 1 from going into alarm at all.
Hello. Have you tried this section in the video? Let me know
'Alarm delay setup' ua-cam.com/video/iTFNnRTnd_A/v-deo.html
What size sim card?
Full size SIM
Добрый день подскажите пожалуйста у меня стоит на двери датчик открывания но срабатывает он только при повторном при первом открытии дверей не срабатывает при повторном открытии срабатывает сигнализацию, как это исправить?
Hello. Unfortunately I don't have experience with the door sensor (Привет. К сожалению, у меня нет опыта работы с датчиком двери.)
@@morneo3 🤚🍹Спасибо.
What is purpose of fixing simcard
What do you mean by fixing sim card? Please try to describe your problem in a different way, maybe I will know the answer
How to do brakup it’s???
Sorry, what do you exactly mean by that? Please try in another words
My system isn't charging. No sim or anything activated yet
So is it working on AC adapter? Or it's working on battery only?
How to reset this one
Hello. According to the manual: "Factory reset - In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep. The main unit gets all its settings cleared and restores to its factory settings successfully."