Thx for this professional video! Because I only speak english and german, I didnt understand the most of the spoken tips and explanations, but even to see what You did and which way You did it helped me to get along with the Hardware/TX Settings. The only thing I'm still unable to find clear informations about is, how strong the tension of the tail bent should be and how i can easily set this tension without taking completly in parts the whole tail holder. This part seems to be constructed a little bit service unfriendly in my opinion. Maybe you can make a perfect video about setting the tail tension too? :=) Greetings from germany!
Hi, I hope it helps. in fact, its been sometimes I made this video, and now I don't have the heli anymore. for adjusting the tension, if I am not wrong, I think you can't adjust the tension as it is built to fit into gap in both side, it made the tension pre-adjusted by factory. But of course you can try to loosen either side may it be the boom holder side or the fin side to check if you can twist and pull to loosen or tighten. If you could set the tension, by measuring the perfect weight, hold the tail blade holder at the same time try to rotate main blade holder, with strength like massaging your arm, over then that it snaps, then it should be ok.
@Jekko Desson .... i need to know .... during your pitch setup ....you disconnected the motor wire ..... but i also see you have a throttle hold switch on too... any reason.... ? also did you turn off the gyro switch from receiver .....??
Sheraz Asad .. you can swith on idleup too during setup as long as motor wire is disconected. Reason is that if I remain at normal mode, my low pitch will be at -15% (i need low pitch to go -100% so that I can set my desired degree at low pitch), at throttle hold, I have L -100 M 0 H 100 (same with idleup). I did not switch off gyro.
thanks for reply Jekko...i got your point here.... one more thing i need to know how you setup your tail mechanically ?? ... because mine heli tail is not head lock... can you guide me that.... thanks in advance...
Should be ok. try adjust tail shaft slider inside more. if you look from behind the heli, adjust the slider to left more ( maybe try 3 turns at tail control ball link), you can feel it after that whether to add or reduce. that should solve the problem.
My WALKERA "V450D03" is new, and i can´t use it because there is a great PROBLEM: - i turn on the radio (DEVO7), the battery on the Heli, I try all the commands with the throttle at low speed, then i throttle all down and trigg the "HLD Button" (Throttle OFF). THEN IF I MOVE IN ANY COMAND (RUDDER / ELEVATOR / AILERON) THE ENGINE TURNS ON AT LOW ROTATION AND ONLY I CAN STOP IT BY TURNING OFF THE BATTERY ( including the "Throttle HLLD" does not act). I ALREADY SAW ALL THE CONFIGURATIOS OF THE RADIO. AND I CANNOT DETECT THE CAUSE OF THIS PROBLEM. CAN SOMEONE HELP ME? THANK YOU
@@PLANETHELITVThank you very much for your kind support. WALKERA "technical support"???? I'm sick of sending them Emails that they don't even bother to answer !!!!! By the way, what is the "official site" of "WALKERA" for HELICOPTERS ???? In "www.walkera.com" they only deal with Drones !!!!
Okay, there is another possibility. Maybe the factory screw up the redio setting.. Can you video of take a photo of every detail inside you tx setting, i will see if anything wrong with it. You can send them to jekkodesson@gmail.com
I recentl bought a "WALKERA W450D03" and and still haven't even used it "2" PITCH SERVOS ALREADY BURNED OUT WHEN I ONLY WAS CONFIGURING THEM. Can someone tell me why? Thanks
bonjours et merci pour ta vidéo , je remet en route un hélico 450 v2 et j' ai une radio devo 7 comme la tienne et j' aimerais savoir si tu pouvais me dire ou brancher mes servos sur mon récepteur car je ne me rappelle plus comment les brancher pour que le plateau cyclique puisse monter droit et tu n' utilise pas de gyro sur ton hélico ? juste ton récepteur walkera merci d avance pour tes réponses et j' espère que tu va bien m'aider comme ça je pourrai refaire voler mon hélico grâce à toi merci .
WHERE IS "WALKERA Helicopters" ???? Either it is a GREAT SWINDLE or it DOES NOT EXIST !!!!!!!!!!!!!!!! Everyone is SELLING "HELICOPTERS AND ALL THEIR ACCESSORIES" from the "WALKERA" brand ...... BUT WHAT A GREAT VIGARICE After all what is "WALKERA" ????? A "FALSE FACADE" ?????
ninice video but yo go to fast. I cant seem to get to gyro settings i accidentally reset my tx fm1 tail wag fm 1 and 2 no tail wag but when i go to inverted flight the heli peroets like crazy and dropps out of the sky
Hi joseph, sorry i skipped gyro in this video, as i said in indonesian you should set gyro accordingly. So set your gyro to automatic instead of manual. And you can set 70-80 for normal mode and f1 to maybe 75, fmode to to 72, depending on th you use during fmode 1 and 2.
WHERE IS "WALKERA Helicopters" ???? Either it is a GREAT SWINDLE or it DOES NOT EXIST !!!!!!!!!!!!!!!! Everyone is SELLING "HELICOPTERS AND ALL THEIR ACCESSORIES" from the "WALKERA" brand ...... BUT WHAT A GREAT VIGARICE After all what is "WALKERA" ????? A "FALSE FACADE" ?????
Thx for this professional video! Because I only speak english and german, I didnt understand the most of the spoken tips and explanations, but even to see what You did and which way You did it helped me to get along with the Hardware/TX Settings. The only thing I'm still unable to find clear informations about is, how strong the tension of the tail bent should be and how i can easily set this tension without taking completly in parts the whole tail holder. This part seems to be constructed a little bit service unfriendly in my opinion. Maybe you can make a perfect video about setting the tail tension too? :=) Greetings from germany!
Hi, I hope it helps. in fact, its been sometimes I made this video, and now I don't have the heli anymore. for adjusting the tension, if I am not wrong, I think you can't adjust the tension as it is built to fit into gap in both side, it made the tension pre-adjusted by factory. But of course you can try to loosen either side may it be the boom holder side or the fin side to check if you can twist and pull to loosen or tighten. If you could set the tension, by measuring the perfect weight, hold the tail blade holder at the same time try to rotate main blade holder, with strength like massaging your arm, over then that it snaps, then it should be ok.
@Jekko Desson .... i need to know .... during your pitch setup ....you disconnected the motor wire ..... but i also see you have a throttle hold switch on too... any reason.... ? also did you turn off the gyro switch from receiver .....??
Sheraz Asad .. you can swith on idleup too during setup as long as motor wire is disconected. Reason is that if I remain at normal mode, my low pitch will be at -15% (i need low pitch to go -100% so that I can set my desired degree at low pitch), at throttle hold, I have L -100 M 0 H 100 (same with idleup). I did not switch off gyro.
thanks for reply Jekko...i got your point here.... one more thing i need to know how you setup your tail mechanically ?? ... because mine heli tail is not head lock... can you guide me that.... thanks in advance...
@Sheraz ..Whats your gyro setting in transmitter?
Mode - Manual
Switch - Mix SW
Pos 0 = 75.0%
Pos 1 = 70.0%
Pos 2 = 50.0%
these are my settings
Should be ok. try adjust tail shaft slider inside more. if you look from behind the heli, adjust the slider to left more ( maybe try 3 turns at tail control ball link), you can feel it after that whether to add or reduce. that should solve the problem.
My WALKERA "V450D03" is new, and i can´t use it because there is a great PROBLEM: - i turn on the radio (DEVO7), the battery on the Heli, I try all the commands with the throttle at low speed, then i throttle all down and trigg the "HLD Button" (Throttle OFF). THEN IF I MOVE IN ANY COMAND (RUDDER / ELEVATOR / AILERON) THE ENGINE TURNS ON AT LOW ROTATION AND ONLY I CAN STOP IT BY TURNING OFF THE BATTERY (
including the "Throttle HLLD" does not act). I ALREADY SAW ALL THE CONFIGURATIOS OF THE RADIO. AND I CANNOT DETECT THE CAUSE OF THIS PROBLEM.
CAN SOMEONE HELP ME? THANK YOU
I think that is maybe a factory defect. You can video the issue and send it to walkera for technical support.
@@PLANETHELITVThank you very much for your kind support.
WALKERA "technical support"????
I'm sick of sending them Emails that they don't even bother to answer !!!!!
By the way, what is the "official site" of "WALKERA" for HELICOPTERS ???? In "www.walkera.com" they only deal with Drones !!!!
Okay, there is another possibility. Maybe the factory screw up the redio setting.. Can you video of take a photo of every detail inside you tx setting, i will see if anything wrong with it. You can send them to jekkodesson@gmail.com
@@PLANETHELITV Ok Jekko, i'll do it.
AGAIN, MANY THANKS. (my Email: marpir_1946@hotmail.com)
I recentl bought a "WALKERA W450D03" and and still haven't even used it "2" PITCH SERVOS ALREADY BURNED OUT WHEN I ONLY WAS CONFIGURING THEM. Can someone tell me why? Thanks
Hi Roberto,
Thanks for the like.
have a good day
where the shop place?
we are at batam indonesia
bonjours et merci pour ta vidéo , je remet en route un hélico 450 v2 et j' ai une radio devo 7 comme la tienne et j' aimerais savoir si tu pouvais me dire ou brancher mes servos sur mon récepteur car je ne me rappelle plus comment les brancher pour que le plateau cyclique puisse monter droit et tu n' utilise pas de gyro sur ton hélico ? juste ton récepteur walkera merci d avance pour tes réponses et j' espère que tu va bien m'aider comme ça je pourrai refaire voler mon hélico grâce à toi merci .
Om kalo helinya tiba2 muter2 cara settingnya bagaimana ?
WHERE IS "WALKERA Helicopters" ????
Either it is a GREAT SWINDLE or it DOES NOT EXIST !!!!!!!!!!!!!!!!
Everyone is SELLING "HELICOPTERS AND ALL THEIR ACCESSORIES" from the "WALKERA" brand ...... BUT WHAT A GREAT VIGARICE
After all what is "WALKERA" ????? A "FALSE FACADE" ?????
ninice video but yo go to fast. I cant seem to get to gyro settings i accidentally reset my tx fm1 tail wag fm 1 and 2 no tail wag but when i go to inverted flight the heli peroets like crazy and dropps out of the sky
Hi joseph, sorry i skipped gyro in this video, as i said in indonesian you should set gyro accordingly.
So set your gyro to automatic instead of manual. And you can set 70-80 for normal mode and f1 to maybe 75, fmode to to 72, depending on th you use during fmode 1 and 2.
not fo43ngis
WHERE IS "WALKERA Helicopters" ????
Either it is a GREAT SWINDLE or it DOES NOT EXIST !!!!!!!!!!!!!!!!
Everyone is SELLING "HELICOPTERS AND ALL THEIR ACCESSORIES" from the "WALKERA" brand ...... BUT WHAT A GREAT VIGARICE
After all what is "WALKERA" ????? A "FALSE FACADE" ?????