@@WSVAD Okay smart guy. Change it in the middle of nowhere in the middle of the night because it broke down. I always recommend the best quality parts to my customers and that's why I'm still in business.
@@WSVAD Firstly I'm not showing off. I'm stating a fact about the quality of the parts I prefer to use. As far as your work going for hundreds of thousands of what exactly? You're the one trying to show off by saying what you make..... Or claim to make. I'd expect nothing less from the only people on earth who're considered to be more ignorant than Americans. By all means keep using your imagination in the comment section. It lets everyone know exactly what type of person you are.
Сальники самые параша. Если заметили он плотно сидит на клапане а не на посадочном. И получается он поднимится вместе с клапаном там и зависнет или разорвет, потом будете удивялтся что масло то поджирает и не хило. У меня на камазе так же сколько сальников променял пока не нашел какие то немецкие с ободом из алюминия а внутри прорезиненны. Так если ставляешь подобронная втулкой и ударом маленького молоточка. И о боже Камаз 11.9 обьема от замены до замены 800 грамм расхода. Вместо сальников на видео можно и пакетом закрыть не будет разницы.
@@Budni_Rechnika эти колпачки так и задуманные - в двигателей "V", с распредвала в блоке. Примерно Форд Таунус 20М такое... У старых с V4 отсутствовали колпачки с были резинки двигающиеся с стержня клапана...
Nice job, a little grease on the collets or valve make the them just stick in place, making it easier and quicker. Also a drop of oil on the valve stem for the seal is a good idea. Great work. 🙂👍
Also saw a vid the other day of someone taking a single-ended spammer wrench that had a head/profile just smaller than the diameter of the valve collet. Anyways he takes a clear cutting of plastic, under the wrench profile and above the collet, and he just pushes down and the plastic tears a small whole from the tip of the valve stem and the plastic just pushes the valve locks (keepers) pushed right down into the collet and locked into place. Hope that ever helps 😊🤙
Assembly lube!!!!! If I have to tell another one of you fools that I'm going to come over there and teach you all how to repair vehicles. It seems like you can use some decent mechanics. Maybe when you can design a reliable vehicle I'll take you all seriously.
@@gravyd316 it works. There's any trouble in all the reparings I've made. When you don't have the correct grease you can use chasis grease in not lubricated areas
@@angelicgoon5252 Agreed, but he never fully let off the pressure, you can see he's only letting up enough to hold it there. I've had to use a trick like this on a Honda GL1800 when a customer didn't want to pay for taking the head off the unit to replace leaking valve guide seals. The thing was to have everything ready and once you start you can't let the pressure off without removing the keeper. Helps that most powersports only have one retainer slot, let off to much pressure and it just shoots pops right out.
just make sure you use the ones with a metal base and not these horrible full silicon ones. VSS are cheap already so trying to save on these is only going to lead to issues later on(if not instantly)
A mecanica e uma arte quando vemos os detalhes .....trabalhei com o Senhor chico mecanico diesel olha ajudei muito a montar motor no mato sem recurso era de uma sabedoria colocar os motores Caterpilar, Scania ,Cummins sem nenhum gabarito e no final tudo perfeito no relogio .Um grande artista das antiga hoje ele curte a aposentadoria contando historia da mecanica do Brasil......
Is that ohv engine? I have worked on these engines on car mechanic simulator especially old cars. I am assuming these springs are called rockers or rocker arms
Как то во время капиталки, выстрелил у меня сухарик и улетел в неизвестном направлении, у меня чуть истерика не случилась, все полы подмел, все что можно передвинул. Когда нашёл счастью не было предела.
Ich kenne nur die Version mit Blechhülse die eingeschlagen werden müssen,tausende Mal gemacht (Motoreninstandsetzung,Zylinderkopfbearbeitung) Diese Version kenne ich nicht,aber die Technik verändert sich immer weiter.😮
HE SHOULD HAVE OILED THOSE VALVE STEM OILSEALS TO STOP THEM BEING DAMAGED WHEN. INSTALLING ,EVEN SOMEONE WHO IS SUPPOSED TO KNOW WHAT THEY ARE DOING,GET IT WRONG
The cheapest valve seals ... good for you
А нам похер, не понравился, поменяем.
Sometimes cheap is the best if not the only option frfr but I'd agree they look pretty janky😂
@@WSVAD Okay smart guy. Change it in the middle of nowhere in the middle of the night because it broke down. I always recommend the best quality parts to my customers and that's why I'm still in business.
@@gravyd316 продолжай выпендриваться, а моя работа сотни тысяч ходит, нет претензий от клиентов. Сколько людей-столько мнений.
@@WSVAD Firstly I'm not showing off. I'm stating a fact about the quality of the parts I prefer to use. As far as your work going for hundreds of thousands of what exactly? You're the one trying to show off by saying what you make..... Or claim to make. I'd expect nothing less from the only people on earth who're considered to be more ignorant than Americans. By all means keep using your imagination in the comment section. It lets everyone know exactly what type of person you are.
That bolt looks like it’s gonna rip the threads out any second
И прилетит в лоб)
@@user-hf8tj7vm4pexperience?😂
Угол под упор изменить...
В лоб и палец сломает
Looks like the whole head is flexing.
Помню, в детстве помогала отцу засухаривать эти клапаны
Сальники самые параша. Если заметили он плотно сидит на клапане а не на посадочном. И получается он поднимится вместе с клапаном там и зависнет или разорвет, потом будете удивялтся что масло то поджирает и не хило. У меня на камазе так же сколько сальников променял пока не нашел какие то немецкие с ободом из алюминия а внутри прорезиненны. Так если ставляешь подобронная втулкой и ударом маленького молоточка. И о боже Камаз 11.9 обьема от замены до замены 800 грамм расхода. Вместо сальников на видео можно и пакетом закрыть не будет разницы.
Согласен,колпачки шляпа,они должны запрессовываться на направляющую так,что зубами не выдерешь)Здравствуй масложор_название видео)
𝐏
😊
@@Budni_Rechnika эти колпачки так и задуманные - в двигателей "V", с распредвала в блоке. Примерно Форд Таунус 20М такое... У старых с V4 отсутствовали колпачки с были резинки двигающиеся с стержня клапана...
Hes a keeper!🧑🔧😁
Mechanical Engineering ❤
Use a small dab of grease on the valve keeper's to hold them in-place while compressing the valve spring.
Meu primo sem essa ferramenta adequada, passou 4 horas pra colocar essas 8 válvulas 😂😂😂😂😂
Я их головкой обычно забиваю, а тут руками одели😂😂😂
Примерно так же 🫵ты появился на свет😂 тебя тоже головкой забивали🤣🤣
Пробовал резинкой,лучше когда в центре отверствие))
This is one of the most beautiful parts of mechanics😊😊
It is amazing
@@DeaDEye.21z6ss
Nice job, a little grease on the collets or valve make the them just stick in place, making it easier and quicker. Also a drop of oil on the valve stem for the seal is a good idea. Great work. 🙂👍
Also saw a vid the other day of someone taking a single-ended spammer wrench that had a head/profile just smaller than the diameter of the valve collet. Anyways he takes a clear cutting of plastic, under the wrench profile and above the collet, and he just pushes down and the plastic tears a small whole from the tip of the valve stem and the plastic just pushes the valve locks (keepers) pushed right down into the collet and locked into place. Hope that ever helps 😊🤙
Assembly lube!!!!! If I have to tell another one of you fools that I'm going to come over there and teach you all how to repair vehicles. It seems like you can use some decent mechanics. Maybe when you can design a reliable vehicle I'll take you all seriously.
Чё-то слишком легко колпачки надеваются🤔
this version of the song is beautiful, the tips too
I love this song version
Remove the lyrics and treat this as a different entirely new song then sure...
I did the tappet replacement on my Evo 5. Was sooo difficult without the bent tool that you're using!
Главное поднять поршень вверх и убедиться что он действительно вверху.
Precision work. Just a guy installing valve stem seals and then the keepers after skipping the part of placing the spring and retainer. 👍👍
That song is more relevant today than it ever was.
Судя по тому как колпачек сел на направляйку. Он от другого двигателя
The skin condition says a lot! Keep spannering brother! ❤❤
My thoughts
@@darrenplotts5685 🥹❤️👑
Spanners 🔧 are better than wrenches 🔧
Это его работа
перчатки нужно одевать
Finally someone using a proper tool for the job yay great job...😂❤
Add some grease inside the valve seals, it works as a glue and avoids to the seal to waste too soon by the friction
Actually there's assembly lube for that. Grease isn't intended to be used as glue or a sealant. Where do you guys come up with these silly ideas?
@@gravyd316 it works. There's any trouble in all the reparings I've made. When you don't have the correct grease you can use chasis grease in not lubricated areas
The only electric item here is the batteries for the flashlight
True craftsmanship and mechanics there baby beautiful work love it
Never seen external valve seals before
странные маслосъемные колпачки, они даже не фиксируются.
HE WILL BE DOING THE SAME JOB ON THE SAME ENGINE IN A COUPLE OF MONTHS.
Great video, well done!
God I don’t miss putting heads back together after porting and polishing them!
Forget the video I need this song.
More silence please. That means no shitty music please.
My 350 TBI needs this job done
Вы все не туда смотрите, посмотрите какой разбитый клапан когда он одевает масляные колпачки.......
I still remember the first time I saw a pneumatic valvespring compressor... thinking "what sorcery is THIS?!"
Можно просто пинцетом взять сухарики и слегка протереть в солидол, лучше липнут и нервы на месте..
Precision work ?
🤣
Remember a collet getting launched skywards and we never found it had to buy a pack of them
oil on it so it doesn't burn up before the lubrication gets there
I always use both the oring and the umbrella
Those keepers are a balls on my ford focus
remember nobody ever has anything good to say keep it up
Lmfao the tempo on that song I'm dead.
Now You just gotta reehone the piston walls and install new piston rings and then all the exhaust smoke will be gone.
Bending the whole head 😭
Так сальники ставить нельзя. Только через специальную гладкую втулку
Multiple groove valves don't promote rotation.
Those grooves have nothing to do with rotation lol
@@Thumper2Kewl Ya , Right lol 😂
@user-hq2nl2mx7t well it doesn't the 3 rings are designed to allow the valve to rotate freely they don't cause the valve to rotate more or less
@@Thumper2Kewl wrong again, more surface area less rotation.
Dab of grease on each lock ring and you’ll never have to second guess holding it with oily fingers again
how does the seals stay on?? i always glue mine and they are tight fit
EGR? These are valve spring retainers...
People messing around with trade secrets
what a tragic thing to do ,,, Disturbed did not need a cheesy remix.
Bro I’ve been jamming to this for weeks lol it’s good but maybe not your taste, not like that song wasn’t a cover they did anyway
@@killroy3607 fair point
It's one of those catchy grows on you type of songs trust I hated it now I'm listening to it
Love it! ❤❤
I LIҜΣ IT
Und dann gibt's Leute die sagen " Warum arbeitest du nicht mit Handschuhen"
Repetir o vídeo só pela música que lembro a minha adolescência .
Quanto mais o tempo passa mais eu gosto de você... ingrata kkk
Это школа автослесарей ,просто учебное пособие
Acabou com a vedação ao passa-la pelas ranhuras da válvula 😅
Типичный чел который думает,что ему пришла умная мысль
That job is such a booger.👍
I modified claw hammer for spring compression lol .
Там на пружине волос здоровый, после сборки работать клапан не будет😂
Thats a great way to destroy a valve keeper
How exactly would that destroy a valve keeper?
@Block-Shock-and-Fabrication lmao you never install half of a keeper at a time it's a great way the shear the maiting surface off
@@angelicgoon5252 or bend the valve
@@angelicgoon5252 Agreed, but he never fully let off the pressure, you can see he's only letting up enough to hold it there. I've had to use a trick like this on a Honda GL1800 when a customer didn't want to pay for taking the head off the unit to replace leaking valve guide seals. The thing was to have everything ready and once you start you can't let the pressure off without removing the keeper. Helps that most powersports only have one retainer slot, let off to much pressure and it just shoots pops right out.
I gotta do this to my car soon. You make this look easy
just make sure you use the ones with a metal base and not these horrible full silicon ones. VSS are cheap already so trying to save on these is only going to lead to issues later on(if not instantly)
A mecanica e uma arte quando vemos os detalhes .....trabalhei com o Senhor chico mecanico diesel olha ajudei muito a montar motor no mato sem recurso era de uma sabedoria colocar os motores Caterpilar, Scania ,Cummins sem nenhum gabarito e no final tudo perfeito no relogio .Um grande artista das antiga hoje ele curte a aposentadoria contando historia da mecanica do Brasil......
Is that ohv engine? I have worked on these engines on car mechanic simulator especially old cars. I am assuming these springs are called rockers or rocker arms
Как то во время капиталки, выстрелил у меня сухарик и улетел в неизвестном направлении, у меня чуть истерика не случилась, все полы подмел, все что можно передвинул. Когда нашёл счастью не было предела.
Обычно само тело клапана смазывают немного моторным маслом
кто на сухую маслоки одевает
Purpose of the red rubber cups??
Ich kenne nur die Version mit Blechhülse die eingeschlagen werden müssen,tausende Mal gemacht (Motoreninstandsetzung,Zylinderkopfbearbeitung) Diese Version kenne ich nicht,aber die Technik verändert sich immer weiter.😮
I was waiting on the precision....
Why would someone fuk up that Disturbed cover of “Sound of Silence“
Meri bheen 99% orata siraf bachay nu janam he dindiya. Baki sari jimawariya piyo he karda.
You got a hair in there my guy 😂
This song remix goes hardddddd
Song name?
😐The machinist who made those parts watching you say ✨precision✨
Пару раз так сделай, и твоя резьба отрыгнет
Какие тут сальники? Это маслосъемные колпачки.
Those seals were home made or something?I can do this repair with closed eyes.
Get yourself a proper valve spring compressor. You can buy a used Sykes Pickavant one for US $20!
Very good 👍👍👍❤
Кто не знал, это сухарики 😂 ДВЕ корочки 😂
HE SHOULD HAVE OILED THOSE VALVE STEM OILSEALS TO STOP THEM BEING DAMAGED WHEN. INSTALLING ,EVEN SOMEONE WHO IS SUPPOSED TO KNOW WHAT THEY ARE DOING,GET IT WRONG
Are all the long fibers precision?
I guess I have a different definition for precision.
..."Pat...I like to buy a valve"
To be completely honest I don’t like this version of the song
ini cara mechanik yang dibayar. Beda cara mechanik yang diutang
Что за холодец? Самый дешёвый двигатель 😂😂😂
Где вы такие ГБЦ берёте?))) возьми g6ba или AJ3.0 и я посмотрю как так же легко получится 😁
Yeah…like the song suits this video…🤣🤣🤣
Valve spring holder
If mechanics were doing precision work....
They'd be in charge of building the cars.
What about the car builders who aren’t precise?
They are many mechanics that could teach engineers a lot of things
Это вам не ваговские 20клапанные засухаривать 😮
تغيرجلد بلوف بدون فك الراس هذا ممتاز جدا
Зачем изобретать такой "велосипед", когда уже все давно придумано 😅 для старых машин еще подойдет, а для современных бесполезный инструмент
I broke my nail doing this before . Awesome learning experience with a home tool my uncle made
Good n right teknik ....good job ......🎉🎉🎉🎉🎉🎉🎉🎉
Thanks
I love the metal shavings everywhere
Клапана запиздошены с верху кто то уже рассухаривал молотком.
New valve stem seals put on dry 😡
Руки мастера 🎉
ஓம் நமசிவாய அமெரிக்கா🇺🇸🌎