120w + 120w TPA3116 D2 Stereo Amplifier Board | Bluetooth Amplifier
Вставка
- Опубліковано 15 січ 2020
- 120w + 120w TPA3116 D2 Stereo Amplifier Board
Unboxing, connection and test
------------------
Using Comments -
TPA3116d2 Amplifier board
Bluetooth module
Power supply
8 inch woofer
6 inch speaker
7805 IC with Heat sink
________________
TPA3116 D2 Amplifier Board
amzn.to/2uS0Zvp
Bluetooth 4.1 MP3 WAV Decoding Board
amzn.to/35ASUIH
24v 5A power supply
amzn.to/2nG0SzP
Bluetooth Module
amzn.to/2OkgMwi
______________
Please like video and Share
Thanks for watching | Have a good day
------------------------------------
Please Subscribe to get more interesting videos:-
/ sharmajiinfinitycreative
-------------------------------------------
Facebook page
/ s.infinitycreative
------------------------------------
All Playlist videos -
Creative Ideas-
• Creative ideas
DIY Ideas and Life hacks -
• Ideas and Life hacks
Electronics Project -
• Electronics Project
Unboxing and Test
• Unboxing and Test
Solar project -
• Solar Projects
--------------------------------------------------
#TPA3116D2
#BlutoothAmplifier
#SInfinitycreative - Наука та технологія
Yo tengo el mismo y nunca me imaginé que fuera tan potente me levanto por canal 2 bajos es un par de 15" y otro de 10" y si los mueve bastante decente y también su par de medios agudos y super agudos y le tengo de fuente de sonido un ecualizador sansuy y es perfecto para este mini amplificador hace retumbar la casa con un sonido de muchísima calidad creo que el ecualizador le sube la calidad es un buen amplificador lo tengo conectado a 23,2v y 25 mil microfaradios en capacitores y jala bien
Friend ask me a question please, I'm building a sound and I intend to connect 4 5 inch speakers of 25rms each 8ohm, and I'm in doubt on which source to use, do you think a 12v and 10 amp switching source would work for pull the sound quietly?
I got this amp runing with an 18v 3.5 a laptop power supply cord and it sounds amazing. I'm using a mono mp3 module and i dont get that noise
Does it still work?
To avoid extraneous noise, it is necessary to break the "earth loop". In the bluetooth module, it is necessary to unsolder the resistor with zero resistance in the GND-AGND circuit.
Or use the voltage for the bluetooth module from another power source. Here is an example of how this can be done: ua-cam.com/video/D96ZATMz6nk/v-deo.html
What's happening is that the ground return from the audio cable has less ohms than the power supply gnd. So the module is going to ground via the audio cables and you hear these sounds in the speaker. You can hear the sounds change the display blinks(change in current consumption).
Best solution is to power the decoder card using a 5v mobile charger.
Or use B0505s no more seperate power supply no more buzzing or humming sound
bro I watched the video but the circuit pcb are different in mine. could you please guide me in detail what I am going to do to solve this issue. because I am so stuck.
كيف ممكن
Class D amplifier is the best
Yep they have good ifficiency and less heat
But class ab amp sub is the best
nope, i think class H is the best.
It's real price this board
@@tlmeena4256 pls. Do not buy this amp bro it sucks i got a damaged product. It came in a damaged package and the audio cable was cut and the amplifer doesn't even work.pls. do not buy
Its all fake, you will not get the power output what they mentioned.
hi, I have a vintage car with the original amplifier. For you will be possible to use this board just for amplifiing the output of the existing amplifier? i mean , in thethe 3 wires connection ( input of the board) can i connect the speaker output off the old amplifier in series??
Ay amplifier a ki 3w e 2 ta 10w e 2 ta 30w er 1 ta 4♎ te ase ar akta 5w 8♎ use krte parbo sate mp3 decoder with Bluetooth use krle ki kno problem hobe?
I also connected bt pannel as you did but its getting burnt after some days, some bt pannel start to change mode automatically or starts searching automatically, sometimes remotes stops working
I would like to add some range for the bluetooth.mine only works 5 ft.
Muy buen amplificador buena instrucción pregunta el módulo MP3 debe ser mudo o con audio yo triny
Hello, this 7805 transistor, can I put 24v at the input?
I have 2 4 wat speckers.
2 TPA3118 PBTL Mono DC8-24V 60W Digital Audio Amplifier Board to drive the speckers.
1 19.5 v 90w max power adapter.
1 12 v 2500ma laptop power adapter.
Will the 12 power sapply 2.5 A be good aneff to drive both Amplifier Board?
Will the 2 TPA3118 PBTL Mono DC8-24V 60W Digital Audio Amplifier Board get hot?
My son says I need 100w and 15 to 20 amps to drive the 2 speckers. is that so.
Hello, excelete your video, could you give me the diagram of how to add a potentiometer in this project?
I do miss low bass with this tda7498 chip. sounds very raw.
Hi, I bought a Tpa3116d2 bluetooth, and I connected a Grunding Audiorama 4000 to it. It splits the eardrums and has some crazy bass. Bye bye
Este amplificador aquece muito?
Nice setup I bought the board but I can not find the Bluetooth BT-max anywhere the item was not available on Amazon. Do you know where I can find it?
Olá boa tarde, estou com um problema, tenho um sistema de som da creative 5.0 e coloquei lhe uma placa bluetooth tpa3116d2 stério amplificada, fiz a conexão em paralelo da corrente da creative ambas são de 12v, a saída de som bluetooth, na entrada de som da creative, mas quando ligo à corrente faz muito barulho e já me queimou o fusível o que me aconselha.
Crystal clear sound clarity
Bro.. 2 woofer 8" (70watt) and 2 twitter 3".. Iske liye kaunsa board best rahega?
Bluetooth panelinu noise undallo
Don't stepdown the same supply to 5 volt use different 5 volt supply or use mobile charger to power usb module it will remove unwanted noise
Can you explain if is possible add amp to bt speaker
12V powered for full hod ?
Thanks bruh very helpful 😂
Can i bridge this amp to run 8 ohm mono
At high volume with relay circuit it throws pop ups
(7805 IC with Heat sink), What is it for and where can I buy it?
How fixe this board trunoff bad sound in speaker
Whether I can give 3+3 parallel speakers (8ohms per channel)?
hello I bought this amplifier, I want to mount it in a portable radio and I will power it with 14 volts with 4 3000 mha 18650 batteries (approx) in 4S, I am looking for suitable 3 inch square speakers what can you recommend?
Queria que VC ligasse uma placa tpa3116 no som de carro
Holle puedo adaptar dos módulos de anplificacion juntos para más poder y más bocinas
Otimo projeto
Can load 12inch 100w speaker
how do you do to control the volume without the knob
Nice video but quite a lot of noise that pass to the speakers...
And bro in dc power supply pls give the ground earth line to avoid high huming
😉
E a fonte de alimentação dc bro in dc fornece a linha de aterramento para evitar zumbido alto
I connect the ground cable of bluetooth module into amplifier ground channel to erase the humm noise...
Bisa untuk 12 vol
Noise when connected a bluetooth ?
Can i run it on 12v 3amp adapter?
Yo traigo el mismo equipo en mi vocho pero no supe que bocinas ponerle
how do you like the noise when idle? xD
Get a power supply filter for the bluetooth module (B0505s/B1205s/B2405s or whatever fits your setup) or PS filter for amp(class d filter). i use both tbh.
Great job tho, I enjoyed the video :-)
Do you have links for this filter?i have the same problem
Tpa3116nu മാച്ച് ആവുന്ന ബാസ് ട്രെബിൾ ബോർഡ് പറഞ്ഞു തരുമോ.
Where can I get all the part s to make one or where can I order them .I would like to know thank u
You should do somthing for ground loop noise
Why people mistakenly tells that this is 120 watt.just look at TPA ics datasheet and manufacturer says it just only 50 watt at 4 ohms and 30watt at 8 ohms.but still people blindly says 120Wats.strange..
Friend Would it be possible to use a 12V and 5A source of Aliexpress to connect this board and sound play perfectly?
24v better
บลูกับแอมเท่าไรครับ
Okatha volem cantrol Hari karanna kohomada
The card is of good quality, but it doesn't provide 120W per channel, not even close to 100W rms.
El ruido de interferencia es del amplificador o de el decodificador bluethot?
Tem que fazer um aterramento do gnd pro negativo da fonte
wah powernya kayaknya bagus nich,,,,
Por qué le entra mucho ruido , es por la fuente o es por la etapa del Bluetooth ? Es un ruido residual , por favor explícame
Bad noise between the bluetooth/fm/TF module and the amplifier. Maybe using coaxial cables per line in channel would eliminate the noise...
Does it work with 12 0 1 amp transformer?
if the amplifier card is bluetooth, why use another bluetooth card? does not conflict?
I am supplying 12v 1.5 amp DC. When I increase the vol. The power led starts blinking and the amplifier do not work properly. Please help
Better use 24volt power suply
12v dc tv setupbox charger apply it's ok or not ok
This is a great tutorial"leaving my footprint here and im waiting for your turn thanks
I'm going to buy this so first I see the sound quality
Maaf mas kok gak pake tun control ya...
Mosfet what effect...please
Só tem 50w x 2 conforme o datashet em 24v
A este amplificador le puedo instalar un torna mesa ?
Boom box banane ke liye acha hai kya kit?
Cómo puedo conseguir un amplificador de estos
Noise bro, denging
Nice video, like it, thanks for sharing :)
what is impedance of your speakers.
Sir His board me kitna amp transformer dena hai
Mạch nối kiểu này 100% bị nhiễu nặng.
Coloca um modulo isolador b1212s 1w que esse zumbido vai parar!
Что такое цифровой шум? У меня пищит не только на блютуз. Такой же шум как у вас.
Ye board direct 12 v battery se chal sakta hai kya or continue 10 hours chalane per hit hoga ya nahi
without signal, its too noisy...did I hear it right?
Hello sir this project working battery. 12v
Ples makeing battery project this sistum
My need a circuit, where find it....?
Minuto boa
12v Transform connection pannalma
cool
Hi sir use two 10 inches woofer
EXISTE COMMO RESETAR A PLAQUINHA FM MUSIC SPEAKERS
Modifed Antenna, DC12V and RCA ADAPTER INPUT AND OUTPUT
tem um ruído no fundo que incomoda muito
deben poner parlante o woofer del mismo tamaño, nunca diferentes tamaños y mucho menos de diferentes impedancias ni vatajes
the bluetooth module must be powered from a separate power supply and the interference will disappear.
How would this be possible? Options?
Good
Sir his board me bass treble kaise lagata he
Modyul jal gyea na 😂😂😂
what is the price of your speaker's
ชุดเท่าไหร่ครับ
why 5V on the bluetooth module with display? They writing USE 12-24V
Bang saya beli online, pas dicoba dirumah channel nya mati 1. itu kira2 apanya ya?
Transistor 7805 ic what tip41
faltou só eliminar o chiado 😉
link pembelian tpa nya dong gan?
What is that mosfet???
are bhai yah kit kahan milegi please bataiye