This was very helpful. We're working on GX120s in our class and our teacher isn't super clear on how to change the clearance. He's a little irritable, too, so I can't ask him without getting too nervous. Otherwise, this helped me a lot, thanks! :-)
Hello, thank you for this video! Very informative and awesome! I'm pretty handy but this one has me quite puzzled. I have a Honda GX160 motor and it will not start. I have cleaned the carburetor thoroughly. The spark plug has spark. The filter is clean. It has new gas/oil and the switch is set to on. I sprayed carburetor cleaner in the air filter and it acted like it wanted to start but did not. I took the valve cover off and the right side rocker was not on the push rod. Before I re-positioned the rocker, no gas would go to the spark plug. As soon as the rocker was back in place and I pulled the cord a couple times gas made it's way to the spark plug, but the engine still will not start. The motor sat with no oil for about a year, worked just fine before it sat idle. The only mods I've done to the engine was remove the governor and disable the oil level sensor by unplugging the yellow cord. I would appreciate any of your expertise or advice you have on this issue, thank you in advance for your time.
@JOATD yeh that's good then. I'm just to adjust mine. The engine only runs with the choke on, I've cleaned the carbs, checked the fuel, float and jets, new air filter etc, so that'll be the next option.
@callanmurphy9807 yeah that would be my next step also. Seems to me that you have already taken care of everything that normally gives you that problem.
I learned this lesson today!! Glove they make us wear at work got wrapped around a thread when I was sending a bolt home. Luckily the glove ripped before my hand
Thanks for posting this so I can get an idea of how to do this. Honda service manual suggests doing this along with the timing chain at 100k and I'm at 92-93k now.
Been taking a quick break to see some family. Ever since I joined the Navy, moved to VA then got out of the Navy and became a contractor I haven't seen my family at all...about 11 years. So I'm catching up on time because a lot of them are very old and haven't met my daughter and wife yet. I haven't lost motivation, just taking care of some past due family time.
Hi dear , thanks for yours great and helpful videos, and i have some questions. I have a honda generator Model eu 3000is , I would like to know for setting up the valves adjust: How much is the clesran setting for the exhaust fuel gauge valve gap-00 .? And how much is the clearance seting for the intak fuel gage vale gap.00_? I need your instructions please, Thanks
Starting kick is very hard. Removed the spark plug and then tried to pull the cord,found all ok .Tried multiple times with plug removed ,it was ok as usuall.But when installed back the spark plug,it became hard. What is the problem?
how do you do it on on a honda hs70? g300 motor that does not have OHV? there is a side cover to the cylinder that you can check clearance but no adjustment.
Thanks for clearly demonstrating how to find top dead center.
This was very helpful. We're working on GX120s in our class and our teacher isn't super clear on how to change the clearance. He's a little irritable, too, so I can't ask him without getting too nervous. Otherwise, this helped me a lot, thanks! :-)
+The One and Only GodHydra glad I was able to help you out
He's the teacher and doesn't know? Scary
Hello, thank you for this video! Very informative and awesome! I'm pretty handy but this one has me quite puzzled. I have a Honda GX160 motor and it will not start. I have cleaned the carburetor thoroughly. The spark plug has spark. The filter is clean. It has new gas/oil and the switch is set to on. I sprayed carburetor cleaner in the air filter and it acted like it wanted to start but did not. I took the valve cover off and the right side rocker was not on the push rod. Before I re-positioned the rocker, no gas would go to the spark plug. As soon as the rocker was back in place and I pulled the cord a couple times gas made it's way to the spark plug, but the engine still will not start. The motor sat with no oil for about a year, worked just fine before it sat idle. The only mods I've done to the engine was remove the governor and disable the oil level sensor by unplugging the yellow cord. I would appreciate any of your expertise or advice you have on this issue, thank you in advance for your time.
Did you get it sorted mate
@callanmurphy9807 yes I did thank you the exhaust valve rocker arm was not on the valve
@JOATD yeh that's good then. I'm just to adjust mine. The engine only runs with the choke on, I've cleaned the carbs, checked the fuel, float and jets, new air filter etc, so that'll be the next option.
@callanmurphy9807 yeah that would be my next step also. Seems to me that you have already taken care of everything that normally gives you that problem.
@JOATD yeh I thought that much, but I'm winging it from youtube haha. Either that or the fuel mix ratio isn't done correctly and running to much fuel.
Great video. Thank you! You really need to lose the glove around rotating equipment though. Skin will rip but the glove will take your arm OFF !
I learned this lesson today!!
Glove they make us wear at work got wrapped around a thread when I was sending a bolt home.
Luckily the glove ripped before my hand
I have a Chinese engine with no small triangle under the recoil starter. How can i adjust its valves correctly?
Hey man thank you for this video! I got the instructions on paper, but I just want it to watch a professional do it.
Awesome video! Thanks for speeding up through parts we don't need to see, like removing four bolts. Nice job filming! Very clear!
Thanks a lot for the knowledgeable info. kindly explain more about it how may we know the intake valve spring tension or exhaust valve tension ?
Thank you for this. Was able to get my GX200 adjusted in no time!
thanks man this the most clear vid on valve adj , but only thing if could help with is to defin the TDC some do not have the mark
Where do the little springs hook up on the top of the motor?
Thanks for posting this so I can get an idea of how to do this. Honda service manual suggests doing this along with the timing chain at 100k and I'm at 92-93k now.
+BuddyLe3 I noticed you haven't posted any videos in a bit
Been taking a quick break to see some family. Ever since I joined the Navy, moved to VA then got out of the Navy and became a contractor I haven't seen my family at all...about 11 years. So I'm catching up on time because a lot of them are very old and haven't met my daughter and wife yet. I haven't lost motivation, just taking care of some past due family time.
thats a good point, family is much more important anyways.
Hi dear , thanks for yours great and helpful videos, and i have some questions.
I have a honda generator Model eu 3000is , I would like to know for setting up the valves adjust:
How much is the clesran setting for the exhaust fuel gauge valve gap-00 .?
And how much is the clearance seting for the intak fuel gage vale gap.00_?
I need your instructions please,
Thanks
You need to purchase a service manual to get the proper operation
Great explanation. You should teach Small Engine Repair and Maintenance at a college.
Ohd head contains lot of engine oil, what's main cause?
Hi what can it be my honda gx120 engine as low compression will not start thanks
Starting kick is very hard.
Removed the spark plug and then tried to pull the cord,found all ok .Tried multiple times with plug removed ,it was ok as usuall.But when installed back the spark plug,it became hard.
What is the problem?
Did you end up finding out what the issue was?
@@smollyboi tappet setting was out of order.Proper tappet(valves) comply with .Found SAT.
Thanks alot for sharing,absolutely helpful.
If the Piston valves lose am I supposed to just tighten it all the way
you're the man, thanks for the videos on this engine
Ep 1000 valve settings video please
Hey buddy what about if I set up everything properly but I have a too much compression? How can release it
you are not at TDC... I MADE THE SAME MISTAKE ONCE
Any info on the gx100??
how many mm will intake valve and exhaust valve
mighty fine! did the job quick! Thanks
Nice video and nice wrenches love mac tools👉🔧👍
Great video, thanks for sharing your expertise.
please tellme valve clearence of gx390 honda power washer
how do you do it on on a honda hs70? g300 motor that does not have OHV? there is a side cover to the cylinder that you can check clearance but no adjustment.
Thanks a lot
hey bro thanks for the video, was very helpful
cheers mate
Thanks a lot man.
How do I get the flywheel off?
Fart on it
Good Explanation Thanks !!!!
thanks very much so helpful
does anyone know if the Chinese Honda knockoffs are licensed copies or not?
Burt Hulbert i think something got screwed up along the line of patents or some shit like that haha
Hope you have also for GX390, thanks for the video its helpful
Same procedure and specs for the gx390
@@charleshendrick7266 same for gx200 too ?
please I want a service manual
Seems odd some engines need adjustment and some never go out of adjustment,
+Steve Rob that's true, these engines are very crude and bet they could take a lot of shit
ತುಂಬಾ ಉಪಕಾರವಾಯ್ತು
You forgot Mother-fucking beer time! :(
💐✋
Reglaje valve hondagx150
hi sir
I have to Fart
Türkısh language please
C