Cordless Electric Drill Repair | Replaced 5S 21V 20A 18650 BMS Charging Protection Board Part-1
Вставка
- Опубліковано 20 лют 2021
- In this video (Part-1) I’m going to show you how I have fixed the cordless electric drill issue. Issue= isn’t run for long and short-circuit noise from the BMS. The problem is with the Push Button Trigger Switch DC 7.2-24V, which causes later on the issue with the 5S 21V BMS charger board of this drill battery pack. Throughout this video, I have done several troubleshootings to identify the exact causes of failure.
Wiring Diagram @6.24 or @10.20 or @11.12 (All diagrams are correct)
Part 2 video - • How to Repair Cordless...
Cordless Electric Drill OEM Parts.
1. 5S 18/21V 20A Li-Ion Lithium Battery Pack Battery Charging Protection Board - bit.ly/3qEHezf
2. 21V 1.3A Charger Adapter - bit.ly/2NrGOOj
3. Electric Drill Dustproof Speed Control Push Button Trigger Switch DC 7.2-24V Cordless Drill Switch - bit.ly/3sbe8ba
4. RS550 21V Motor 12theeth 8.8mm - bit.ly/3bpbOqb
5. 21v Cordless Electric Screwdriver BMS with Cases - bit.ly/2NONlCt
Subscribe LahisTech: bit.ly/2JHtlyc
Subscribe for more future creative project videos.
Thank you. - Навчання та стиль
Nice video. The Part I really wanted to see was the bit you missed out. Taking out the contacts from the board and dc port and how you used them in the battery connector. I bought the bms to give good contacts for battery adapters I need
C’est excellent merci beaucoup pour l’exercice
Really good ideas and good work
You now man you are so talented
Man that’s amazing
It's a useful video. I think it'll be a great help to make a video.
Muito bom teu serviço que Deus continue te abençoando.
JM arte na garagem
Sooooo helpful thanks bro
Nice project
Sanaol magaling sa electronics repair.
Thanks for this video.
Alat nya komplit semangat
Super! 👍
It reminded me I have a similar battery that I want to fix
is there any step by step BMS connection procedure which wire to connect first and to the end?
Pls do PART 2 video
thank you friend! Good luck and health to you!👍🤝
Where's that mat with articulated clamp from at 8:00 and what are the three tips near the arm for?
Why replace BMS part if it is still working? Does it have a timer or hour memory?
i have a similar battery for my electric saw and i was trying to charge the battery with my rc charger via jack but charger cannot find battery , should i solder cables on bms with xt60 ? if yes where do i have to connect the xt60
Such a great idea.
Are those purple cells not of good quality? I saw a guy using them in a ebike battery pack.
@Pinki Chowdhury , They are called adhesive insulation rings. If you write specific number of the lithium cell you will get the exact one. for example - "18650 adhesive insulation ring".
After done soldering, you must charge to active the bms. Learn from sorin
Can I connect direct without the board protection? It brings problems to charge?
Good hit🇮🇳👍👍👍 Kuki
👍👍
Sir where did you Bought you bms and what brand?
bisa gak kalau pakai di inverter?
Hello sir
One of my battery pack Ibell chord less drill of 1500Ah 20vCenter cell failed, can I replace with other Ah, other standby Battary is charging and working
Pl suggest
Thanks
Jacob
The old one is worx type battery, the new one is makita type battery
Please share a link to buy this piece of battery
Can i use bms to power my tool without battery?... I mean just using my 18 volts ac adapter...my battery pack is so expensive i cudnt afford to buy new one...thank you
I have successfully used 12v car battery with 12v dewalt drill . You can try other led acid small battery?
kalo pakai Bms bisa g Bosque
I use the tester on the 20 A range and measure every single element for a few seconds
the test leads are schunt resistor
good batteries exceed 30A
B1 start from battery - not from +
Suldir nya yang berapa wat nya mas
those panasonic batteries have low discharge rate.. your drill will have lower torque
True
The power switch have 1 ic and 1 fet , you can prepair the switch !
Where can i buy it?🙏
can i use 18v battery in 14.4v brushless drill????
Yes!
Bhai ye circut kahan sy milty hen?
May be MOSFET is shorted,
Check MOSFET first in inbuilt bms
I’ve thought it, but this inbuilt BMS is a waste. I wonder how still it’s work with just one high power low internal MOS at least it should have 2or more to balance; poorly built. No Temperature NTC either, hence decided to move on to a replacement. Thanks
@@LahisTechLT some Bosch 18v batteries doesn't use bms,but they also works fine for long time
There life mainly depends on cells used
@@LahisTechLT There is very much a temperature NTC present which can clearly be seen @ 3.19, the small black plastic dot surrounded by white plastic protection.
The test leads were too thin. Any more current or time and they would have melted.
New Green battery then Pink battery what are you doing newbie?
5s 18v 21v Battery Bms
It took only 2 hour to show you the real capacity? Mine is liitokala but it take at least 7-15h to test the capacity
If it's only 900 mAh it shouldn't take much longer than that.
5S, 2P???
O no
All good if you are doing this as a for profit business. For the average person the cost of special spot welder, battery testers, misc tools and parts is too much. You could replace your old battery packs for new ones several times over and simply plug them in to the tool. So thanks but No thanks.
2.5h18vlt
ভাই সার্কিট টা কোথায় পাবো
Fist view
Thanks
Invers baterís wwuuuooooo
Firts
Thanks
👍👍