Kendimde 39 senedir Almanyada tornacıyım. Bu genç Arkadaşı tebrik ediyorum. Bu kadar büyük parçayı işliyor, helal olsun sana. Sadece tavsiyem koruyucu gözlük takması, çünkü gözün tamiri yok. Allah korusun göze birşey olduğu zaman işi de kayıp edersin, gerisini sen düşün artık. İnşallah bundan sonra takarsın. Allaha emanet ol, ülkemin güzel insanı.
عمل رائع جدا من عامل محترف فى الخراطه على درجه دكتور جراح ومهندس،تحيه من زميل فى صناعة الخراطه من مصر،،،،❤❤❤❤❤ امنيه مشدده ان يكون لدى مخراطه مذهله مثل هذه المخراطه،شكرا لك على هذا الموضوع المفيد الجميل ،نريد لك المزيد من النوع الفيديوهات
أشكرك جزيل الشكر على تعليقك الجميل زميلي، وأتمنى أن تتحقق أمنيتك. طبعا سأستمر في تصوير الفيديوهات بكل سرور، هناك فيديوهات مماثلة على قناتي، يمكنكم مشاهدتها الآن، شكرا لكم.
I'm also an old burnt out Ex Toolmaker. The reason I agree with an earlier post about not wearing T-Shirts ..they don't give The protection required as you just have to look at the Floor as everyone knows The Chips are supposed to go in The Chip trays on The Machines . Looking at The work area where the guy is working there's Chips/Swarf everywhere & the guy doesn't even sweep them up. Also when large cuts are made Chips can become very hot & can cause burns so The Operator hasn't done anything to keep his work area clean as a simple Guard to stop The Chips from flying around.
You are right in a way, but the sawdust is always taken by the apprentices. We usually clean it after the work is finished. Unfortunately, I do not like to attach anything to the sawdust to prevent the sawdust from scattering.
I am a retired fitter and turner and you are correct about the swarf going into the tray but with a large job like he is machining the tray would need to be very wide and then making it hard to operate the lathe. Chips are always a problem with big machines. Cheers Ian
I never had the opportunity to operate a lathe at this size during my time as a toolmaker but wearing a t-shirt operating machine like this is a no no in the UK
@@user-ty8gl7im3l it's the law about health and safety in engineering workshop, ie: safety glasses, toecap boot and long sleeves overall. These are the main three things
I'm 81years old I have been a machinist in England and Jamaica working for the largest machine shop in the Caribbean Kingston Industrial Works tee-shirt were worn,helmets were not worn. I've operated lathes as large as this, borers millers and planers
Legal ver uma usinagem de um tubo desse, também sou torneiro de máquina pesada, a 7 anos, mas o mínimo de segurança e usar óculos e protetor auricular, pois os cavacos ,quando a gente menos espera vao em direção dos olhos.mas belo trabalho
Really bro. Goggles is a small cheap thing which protects you from a huge expensive trouble. Even 0.1 mm chip in a eye is a big big trouble. On my previous work I had a collection of damaged goggles. Each of them is an avoided scar/broken eye. Like one guy said here - one time is more than enough for 20 years. I even used fullface because chips hitting the face are annoying. Be safe.
Yes, you are right. I do not wear protective glasses because they bother me. I stay behind sawdust as much as possible, but you are right, we need to wear them for occupational health.
Без очков,в перчатках и кроссовках и футболке...Собрал все нарушения техники безопасности.На нашем предприятии остался бы без премии.А так работа отличная.
I couldn't understand exactly what you meant. We did the precise processing of this workpiece before welding, after the flange was welded. I don't think there was anything missing in threading, and I didn't need a bed.
@@Paul761000 это может ты не токарь. Я на цилиндрах 5 лет на чпу стоял. У нас протачивали под люнет , а потомрасточка и проточка- до 3 соток биение. Прежде чем пиздеть на людей спросил бы что да как , чучело.
@@hydraulicfactory Я вижу, что рабочий берёт пульт без проводов, и кранбалка движется... Я удивлён. I see that the worker takes the remote control without wires, and the crane beam moves... I am surprised.
We use standard metric diamonds. Since we cannot measure the bottom of the teeth of large diameters, we draw them according to the size of the top of the teeth. Since they are large diameters, we do not try them. We send direct installation and there is no problem.
I don't usually use a cooler because water spreads everywhere. I use it when necessary. The sawdust grows when pulling teeth, so it's normal, give it as much water as you want, it will grow when pulling teeth. The inner diameter of the workpiece is important for us. The inner diameter will be HONED, so I reset the sleeve according to the inner diameter.
Kendimde 39 senedir Almanyada tornacıyım. Bu genç Arkadaşı tebrik ediyorum. Bu kadar büyük parçayı işliyor, helal olsun sana. Sadece tavsiyem koruyucu gözlük takması, çünkü gözün tamiri yok. Allah korusun göze birşey olduğu zaman işi de kayıp edersin, gerisini sen düşün artık. İnşallah bundan sonra takarsın. Allaha emanet ol, ülkemin güzel insanı.
Eyvallah sağolasın çok haklısın iyi niyetin güzel yorumunuz için teşekkürler selamlar
cevabinda güzel, kardes@@hydraulicfactory
@@cevdetatnc9066 doğrudur ustam geçmiş de olduğu gibi gelecekte de olacaktır.👍
Всё надо обстучать деталью - и станок, и то, что рядом. Наш человек, лайк!
I don't understand what you mean, can you explain a little more?
У русских два слова нужно пояснять как книга
@@hydraulicfactory
J'admire ces gars qui ont une telle maîtrise de leurs travail.
Thank you, we try to do our job with love, which results in beautiful workmanship and mastery.
Очень крутая работа. Привет токарю Турции от начинающего токаря с Башкортостана
Thank you brother, greetings from Türkiye
👍👍👍👍👍👍
👍👍👍
عمل رائع جدا من عامل محترف فى الخراطه على درجه دكتور جراح ومهندس،تحيه من زميل فى صناعة الخراطه من مصر،،،،❤❤❤❤❤ امنيه مشدده ان يكون لدى مخراطه مذهله مثل هذه المخراطه،شكرا لك على هذا الموضوع المفيد الجميل ،نريد لك المزيد من النوع الفيديوهات
أشكرك جزيل الشكر على تعليقك الجميل زميلي، وأتمنى أن تتحقق أمنيتك. طبعا سأستمر في تصوير الفيديوهات بكل سرور، هناك فيديوهات مماثلة على قناتي، يمكنكم مشاهدتها الآن، شكرا لكم.
Beautiful jobs 👍👍
Thanks bro 😎
Trabalhei de torneiro por 36 anos,bom trabalho amigo 🇧🇷🇧🇷🇧🇷👍
thank you colleague👍💯
I'm also an old burnt out Ex Toolmaker.
The reason I agree with an earlier post about not wearing T-Shirts ..they don't give The protection required as you just have to look at the Floor as everyone knows The Chips are supposed to go in The Chip trays on The Machines .
Looking at The work area where the guy is working there's Chips/Swarf everywhere & the guy doesn't even sweep them up.
Also when large cuts are made Chips can become very hot & can cause burns so The Operator hasn't done anything to keep his work area clean as a simple Guard to stop The Chips from flying around.
You are right in a way, but the sawdust is always taken by the apprentices. We usually clean it after the work is finished. Unfortunately, I do not like to attach anything to the sawdust to prevent the sawdust from scattering.
I am a retired fitter and turner and you are correct about the swarf going into the tray but with a large job like he is machining the tray would need to be very wide and then making it hard to operate the lathe. Chips are always a problem with big machines. Cheers Ian
@@ianlangley987 You are right, my colleague, thank you.
I never had the opportunity to operate a lathe at this size during my time as a toolmaker but wearing a t-shirt operating machine like this is a no no in the UK
Maybe you will get such an opportunity in the future. Working on large machines requires some experience.
What kind of shirt should he be wearing? I too run similar size lathes and wear the same shirts no problem
@@user-ty8gl7im3l Good luck my colleague.
@@user-ty8gl7im3l it's the law about health and safety in engineering workshop, ie: safety glasses, toecap boot and long sleeves overall. These are the main three things
I'm 81years old I have been a machinist in England and Jamaica working for the largest machine shop in the Caribbean Kingston Industrial Works tee-shirt were worn,helmets were not worn. I've operated lathes as large as this, borers millers and planers
In my days we would have an apprentice learning with a skilled workman
Nowadays, it has become really difficult to find an apprentice. We do our best to make people love the profession. I also have an apprentice.
very big machining job my friend...
yes mate
A worthy idea for your workshop wow
Thanks
Legal ver uma usinagem de um tubo desse, também sou torneiro de máquina pesada, a 7 anos, mas o mínimo de segurança e usar óculos e protetor auricular, pois os cavacos ,quando a gente menos espera vao em direção dos olhos.mas belo trabalho
Thank you yes you are right but I am standing behind the sawdust as the pass goes.
Çok güzel bir çalışma
Teşekkürler
Kaliteli işçilik.
Teşekkürler
Really bro. Goggles is a small cheap thing which protects you from a huge expensive trouble. Even 0.1 mm chip in a eye is a big big trouble. On my previous work I had a collection of damaged goggles. Each of them is an avoided scar/broken eye. Like one guy said here - one time is more than enough for 20 years. I even used fullface because chips hitting the face are annoying. Be safe.
Yes brother, you are right, I am aware of this too. Thank you for your warning.
Oh how I love working BIG !
yes i love it too
koruyucu gözlük lazim usta,
is güvenligi önemli.
Evet haklısın kardeşim 👍
pro fessonal ...best......대단합니다. 저도 같은 엔지니어 에요...
Thanks 👍
Thank You
Thanks
Bravo maestre! (pune ochelari, cu ochii nu poti sa gresesti decit de doua ori)
thanks. you are right
Головне не увімкнути оберти, коли до шнурка привязана болванка, а то крану буде кінець.
👍👍👍
No eye protection. Chips flying everywhere.
Yes, you are right. I do not wear protective glasses because they bother me. I stay behind sawdust as much as possible, but you are right, we need to wear them for occupational health.
Thanks safety inspector
👍👍
один раз прилетит чипса -потом будет знать. Достаточно одного раза на предположим 20 лет работы.
@@hydraulicfactory Hangi şirket bu?
Nice work
Thanks 👍
Great job
Thanks
süperrrr
👍👍
Excatly my first job in 1978.i was 21…
I am 35 years old and I started my first job when I was 14.
👏👏
👍👍
👍👍
👍👍
That gigantic OD Micrometer looks like it would be extremy easy to ruin. Probably got to check its calibration frequently?
I use it very carefully, but why should it be ruined? It goes for calibration once a year.
Bende seviniyorum memleketimizde böyle celik ile islemeler, kaliplar, aletlerin üretilmesine . Gurur verici Türkiye, yola devam.
Teşekürler üretmeye devam
Почему не соблюдаются правильна Техники Безопасности !!!! Токарь работает без спец . одежды и обуви !!!!?????
We strictly comply with the safety measures. I use a hard hat and glasses when necessary. I definitely work with protective shoes.
No usa implementos de seguridad especialmente gafas de proteccion a los ojos , no es apto mecanizar con polera con mangas cortas las virutas quema
The weather is very hot so these are summer clothes.
👍👍👍👍👍
👍👍👍
A gdzie kask podczas jazdy suwnica?
Yes you are right
😮
👍👍
💯👏👏👏👏👏👏👏👏
👍👍👍
👏👏👏👏👏👏
👍👍
👏
👍
I love big jobs🤝👍🇧🇷🇺🇸
I love big jobs too.🇹🇷🇹🇷
Это будет ось для мотоцикла?😊
no hydraulic cylinder sleeve
ar fi mai corecta redarea la viteza normala...
I'm speeding up the video because it's taking too long
Hello, what is the factory name? We have some liners inquiry
HÜRSAN PRES
Вот кого надо поддержать предоставить льготы и преференции а не айтишникам
Thanks bro
Такое уже было. При Советской власти. Рабочий получал больше инженера.
@@user-xf2nr2qe8b но почему сейчас это не так
Вот в Китае рабочие в приоритете потому и достигли такого результата
There is no such thing in Turkey, quite the opposite.
@@hydraulicfactory И это - правильно!
Government will close this shop if you don’t wear safety classes, proper clothes for doing this work in the United States
Occupational safety courses and training are also given in Turkey. The same rules apply in Türkiye too👍
Gone at 5.00 slower speed more feed
There may have been a problem with video merging, we are amateurs when it comes to video.
Без очков,в перчатках и кроссовках и футболке...Собрал все нарушения техники безопасности.На нашем предприятии остался бы без премии.А так работа отличная.
Вы проделали большую работу, приняв меры предосторожности. Спасибо
Where is your safety googles boy?
All security measures have been taken
des tubes pour les plate forme petrolieres j en ai eu fait il y a trente ans
We took over the flag from you, my colleague. 🙂
очень странное решение- на черновой обработке , без подрезки торцов и проточки под люнет нарезать резьбу.
I couldn't understand exactly what you meant. We did the precise processing of this workpiece before welding, after the flange was welded. I don't think there was anything missing in threading, and I didn't need a bed.
Какой люнет? Зачем он? Вы токарь? Видимо нет
@@Paul761000 это может ты не токарь. Я на цилиндрах 5 лет на чпу стоял. У нас протачивали под люнет , а потомрасточка и проточка- до 3 соток биение. Прежде чем пиздеть на людей спросил бы что да как , чучело.
где очки
in the closet bro 😃
No safety glasses?
Of course we have it, we wear it when necessary.
Все ок. Нормально проточил и нарезал. Но сука ОЧКИ НАДЕВАЙ!. А желательно ещё и каску и куртку)
I don't understand what your purpose is
@@hydraulicfactoryhe said "all good but PUT YOUR F$&KIN' GOGGLES ON" :)
thanks👍
Curtis at CEE would cringe watching this…..
no one needs to be ashamed
Токарь управляет кранбалкой с помощью переносного пульта без проводов? Опасно.... А если помеха?
I don't understand exactly what you mean, what could be the point of a wireless remote control?
@@hydraulicfactory Я вижу, что рабочий берёт пульт без проводов, и кранбалка движется... Я удивлён.
I see that the worker takes the remote control without wires, and the crane beam moves... I am surprised.
The crane is only remote controlled. Best regards from Turkey, brother.
@@hydraulicfactory Ок
Cadê o óculos de proteção torneiro??
in the closet😀
че оборотов то так много...
Since we sped up the video, it looks fast.
Резьба не под калибр? У нас ОТК замучает.
I don't understand exactly what you mean. I think there is a problem in translation. What do you mean by iblik?
@@hydraulicfactory A gauge for checking the thread
@@hydraulicfactory Our threaded connections for hydraulics and pipelines for Gazprom are being tested according to a reference threaded sample.
We use standard metric diamonds. Since we cannot measure the bottom of the teeth of large diameters, we draw them according to the size of the top of the teeth. Since they are large diameters, we do not try them. We send direct installation and there is no problem.
@@hydraulicfactory As an option yes .Everyone has the same +--. Tolerance/deviation/ He's in Africa too.
تماااااااااااااااااااااااااااااااام
🥴
if the workpiece falls on me I may be injured
Yes, even a fatal accident may occur. We take the necessary precautions when lifting and lowering the workpiece very heavy to avoid such an incident.
Isso mesmo obicervei
Equipamento de segurança nem um.
Baita irresponsabilidade
Sou torneiro.
Mas nwm um oculos.
Fazendo rosca .
Ta louco
We use safety equipment such as glasses as much as we can. Thank you for your comment, I will be more careful.
Dogrultsaydin biraz çap yamuk dönüyor
İç çapa göre düzeltildi çünkü içinde paso az 😉
Zasto je sve ubrzano?
Does it shorten the video so it lasts less?
Bhai mujhe bhi kam milega
What do you get less bro?
где взяли такого клоуна ? где охлаждение ?тогда стружку будет ломать.это от нагрева резца вьётся. . почему относительно внутр диаметра не выставил ?
I don't usually use a cooler because water spreads everywhere. I use it when necessary. The sawdust grows when pulling teeth, so it's normal, give it as much water as you want, it will grow when pulling teeth. The inner diameter of the workpiece is important for us. The inner diameter will be HONED, so I reset the sleeve according to the inner diameter.
Кому этот видос практекант насмотрется на следующий день без глаз останется, если снимаешь то хоть и про технику безопасности не забудь показать 😢
What deficiencies did you see?
الثمن
what price
Запоров
What
"failed"
Sem óculos de proteção nunca
yes, the weather is very hot so I don't wear it. But I'm trying to be careful. Thanks for the warning.
Are you from? Hugs from Brazil
@@robertoleitedasilva6240 I live in Türkiye, in the city of Konya.
Maszyna źle wyposażona
Niema wentylacji.Przy
żeliwie konieczne. 20 lat
doświadczenia. W tym
przypadku obrabia stalową tuleję.
Wir geben unser Bestes mit der Maschine, die wir haben. Ich finde meine Theke wunderschön🙂
Unsafe work.. Operator Not wearing safety glass and safety helmet…
We have equipment to install it when necessary.
@@hydraulicfactoryit is always necessary.....
👍👍
No safety glasses (eye protection)?! Just plain stupid.
Of course we have it, we wear it when we need it.
If you hire blind people you won't have to pay compensation when they get a chip in the eye.
Thanks for your information.
O cara não tem um pingo de responsabilidade com á sua segurança sem uso de oculos e se coloca em risco a cada segundo
Thanks for your warning
nul le caméraman
handle it buddy, amateur cameraman🙂
It is somewhat silly after a first pass to measure the diameter, also it does not use any type of protection. TOO BAD, TOO BAD.
What does it matter? Is there such a rule? I don't know why, it had to be measured, I measured it.
Measure ten times, cut once. The master is right.
@@mustafagirgin2658 thanks bro👍
@@hydraulicfactory YOU DO NOT KNOW !
what we don't know