Nice another Forza video. Because of this channel I do all my CVT maintenance now. Just wish I could remember where the difference sized screws go for the cover.
That bolt goes in the back under the center... If I could explain how to find it... You can check this by first closing the cover, inserting the bolt, and looking at the length that does not go in. If the bolt fits there, it will protrude about 1cm. If a long bolt goes in there, it will stick out by less than 1cm. With this, you can check where the long bolt goes.
As a mechanic i say this, you should use grease on the drive puly before you putt it together, also Grease on the pins off the shoes from the clutch. Also it didnt need new shoes it did need cleaning and grease. And please spare your body and work on a work bench. Other than that great job !
Great video, Thank you for sharing with us. I'm a proud owner of a Honda Forza myself they're amazing scooters. I have Subscribed also, keep up the great work 🤘
In the case of 350cc, the drivetrain is opened and inspected every 30,000km driven, and the belt is usually replaced at this time. At the same time, we check the condition of surrounding accessories and replace or repair them. So, you can think of it as taking the belt replacement cycle as a standard and looking at everything.
Al minuto 14.34 i rulli vanno messi al contrario, cioè con la parte coperta di plastica verso sinistra, quindi la parte scoperta va come gira il variatore. Se poi sono rulli diversi allora ok.
Bom vídeo como sempre.Fico admirado como o usuário deixa chegar a polia secundária a esse estado de degradação. Revela falta de manutenção que só se resolve com a substituição das peças. Relativamente às sapatas da embreagem, a Honda fabrica essas peças com pouca espessura o que leva a que tenham de ser substituídos com poucos quilómetros. Veja as da malossi que tem o dobro da espessura e material mais durável. Obrigado por ter partilhado o vídeo, que, como sempre brilhante. Abraço 😁😁
I would like to buy the frame slider that is on the front wheel of the front disk, can you send me the link for it please? Keep up the good work, thanks!
I am in Korea. If you live in Korea and do not speak Korean, it will be difficult to purchase even if I tell you. Also, because Korean distributors do not sell overseas, If you live outside of Korea, purchasing may be difficult. Also, I don't know of any overseas sellers. Sorry for not being able to help you
Это может быть временный шум, вызванный трением между «грузом колодки сцепления» и «внешней частью сцепления» внутри ведомой поверхности трансмиссии. В этом случае звук может естественным образом исчезнуть по мере дальнейшей езды. или нет.. Это может быть проблема с «весом колодки сцепления». Однако я думаю, что это не так, потому что пройденный километраж небольшой. Кроме того, шум может быть вызван вытеканием смазки из сцепления. Альтернативно, шум может быть вызван попаданием масла на «ведомую поверхность», контактирующую с ремнем. Поскольку я не открываю и не проверяю ваш мотоцикл самостоятельно, Трудно сказать, какой именно из них является проблематичным. Просто для справки It may be a temporary noise caused by friction between the “clutch shoe weight” and “clutch outer” inside the drivetrain driven face. In this case, the sound may naturally disappear as you drive more. or not.. It may be a “clutch shoe weight” issue. However, I think this is not the case because the km traveled is small. Alternatively, the noise may be caused by grease inside the clutch flowing out. Alternatively, the noise may be caused by oil being exposed to the "driven face" that contacts the belt. Since I am not opening and checking your motorcycle myself, It is difficult to say exactly which one is problematic. Just for reference
Дорогой друг, спасибо за быстрый ответ. Когда я приезжаю в ХОНДА дилер и говорю им об этой проблеме, то они мне отвечают что всё хорошо. Мотоциклу действует хонда гарантия и хонда не хочет признать проблему. @@MotorcycleRepair
@@tafetdriver281 Мотоцикл еще на гарантии. Как насчет того, чтобы еще немного поездить на нем, проверить состояние и снова обратиться в сервисный центр Honda? (Странно, что Хонда говорит, что проблем нет...) The motorcycle is still under warranty. How about driving it some more, checking the condition, and contacting the Honda Service Center again? (It's strange that Honda says there is no problem...)
Дорогой друг, объясню в чём причина. В моей стране холодный климат для мотоциклов. Поэтому мотоциклов продаётся очень немного и механики практически не имеют совсем опыта по ремонту мотоциклов и не знают как это делать. Например в моей стране всего один дилер Хонда и он продаёт очень много автомобилей и всего 15-20 штук мотоциклов разных моделей в год. Когда я взял новый мотоцикл от дилера, то через 20 км потерял переднее стекло, потому что механики не закрепили его как надо. @@MotorcycleRepair
@@tafetdriver281 Эх, на то была причина.. Я думаю, что это действительно прискорбно. Ah, there was a reason for that.. I think this is truly unfortunate.
기본적으로 8 ~ 32 사이즈의 복스알 세트, 이것을 이용할 라체트, 힌지 그리고 일반적인 일자 십자 드라이버, 정도 있으시면 됩니다. 다만 편리를 위해서 전동 임팩 드라이버가 있으면 좋겠으나... 가격이 20만원이 넘는 것이 아니라면 ..그렇게 오래 사용하지도 못하고 고장날 것이라... 이것의 구매는 심각하게 고민후에 결정하시면 됩니다. 사실...이외에도 정비를 하다보면, 편의를 위해서, 안전을 위해서 필요하게 되는것이 많이 발생합니다. 이 부분은 하시다 보면 본인 욕심에 의해서 또 구매를 하게 될수도 있습니다.
이 부품은 일정 회전수가 (RPM)이 증가하면, 원심력에 의해 외부로 밀려나면서 뒷바퀴를 회전 시키는 기능을 가졌습니다. 이는 브레이크 패드처럼 어느정도 사용을 하면, 닳아서 기능을 못하게됩니다. (이때는 알피엠이 올라가도 속도가 나지 않고, 힘이 전달되지 않아 소리만 크고, 제 힘을 낼 수없게 됩니다.) 이정도 되면, 교체를 해주어야 하는 소모품 입니다. 알피엠은 올라가는데...속도가 안난다던지... 언덕을 올라가는데 소리만 크고, 잘 올라가지 않는 현상이 일어나면.. 교체시기가 온것이라고 할 수 있습니다. 또한 이것이 문제가 될때.. 구동계 쪽에서 들리지 않던 소음도 발생하는 경우도 있습니다.
![HONDA FORZA 350 구동계 정비, 에어클리너, 토크렌치조임 Check & Cleaning Scooter CVT (Belt,Variators,Clutch)[기초팁 45탄]](/img/n.gif)
Air pressure cleaning of the air filter box, without covering the engine intake, was gold...
Thank you for watching.
Nice another Forza video. Because of this channel I do all my CVT maintenance now. Just wish I could remember where the difference sized screws go for the cover.
That bolt goes in the back under the center...
If I could explain how to find it...
You can check this by first closing the cover, inserting the bolt, and looking at the length that does not go in.
If the bolt fits there, it will protrude about 1cm.
If a long bolt goes in there, it will stick out by less than 1cm.
With this, you can check where the long bolt goes.
감사합니다.
김명인님 후원 감사합니다. 🤩😍
Thanks for the subtitles.
Thank you so much for watching the video. 😄
You did an effective job, giving the scooter owner many more kilometers of trouble free riding.
Thank you for your kind words and comments. 😊
As a mechanic i say this, you should use grease on the drive puly before you putt it together, also Grease on the pins off the shoes from the clutch.
Also it didnt need new shoes it did need cleaning and grease.
And please spare your body and work on a work bench.
Other than that great job !
Thank you for your kind words.
Отличная работа!
Спасибо за оставленный приятный комментарий. 😍
Great video, Thank you for sharing with us. I'm a proud owner of a Honda Forza myself they're amazing scooters. I have Subscribed also, keep up the great work 🤘
Thank you for your kind words. I will continue to work hard in the future. 😄
Thank you very much fir that guide! Greetings from Austria :)
I'm glad you watched and found it helpful. thank you
잘봤습니다..ㅎㅎ
형님 이왕이면 클러치작업하실때는 방진마스크 끼시던지 아님 파츠크리너로 딱고하세요 크러치 먼지가 몸에 헤로답니다 ㅠㅠ 페암위험해요
좋은 말씀 정말 감사합니다. 😍
센터 사장님에게 꼭 전달하도록 하겠습니다.
I was wondering how you know it is Time or decision point to replace the parts.
In the case of 350cc, the drivetrain is opened and inspected every 30,000km driven, and the belt is usually replaced at this time.
At the same time, we check the condition of surrounding accessories and replace or repair them.
So, you can think of it as taking the belt replacement cycle as a standard and looking at everything.
I do this manually on my forza,no power tools ramp or bench and it sucks,kills my back,thanks for your vids i like your channel very nice
After all the hard work, there will be reward. I hope you find strength.😊
Al minuto 14.34 i rulli vanno messi al contrario, cioè con la parte coperta di plastica verso sinistra, quindi la parte scoperta va come gira il variatore. Se poi sono rulli diversi allora ok.
Thank you for your interest and for leaving a comment.
22:59 сколько должен быть момент затяжки этой гайки? Я нигде не нашёл этой информации. Спасибо.🔧
I looking for this torque value too.
수고 하셧습니다
감사합니다.
즐거운 명절 연휴 보내시길 바랍니다. 😄
Bom vídeo como sempre.Fico admirado como o usuário deixa chegar a polia secundária a esse estado de degradação. Revela falta de manutenção que só se resolve com a substituição das peças.
Relativamente às sapatas da embreagem, a Honda fabrica essas peças com pouca espessura o que leva a que tenham de ser substituídos com poucos quilómetros. Veja as da malossi que tem o dobro da espessura e material mais durável. Obrigado por ter partilhado o vídeo, que, como sempre brilhante. Abraço 😁😁
Obrigado por assistir ao vídeo e fornecer boas informações. Vou tomar nota.
Anyone knows what the stock weight for roller for forza 350?
Each original roller for Forza 350 weighs 20g.
@@MotorcycleRepair tq.
After how much kilometers have you changed the parts? Nice video,like it. Greetings from Germany
Usually, the drivetrain is opened, inspected, and replaced every 30,000km of driving. 😄
what is the exact size of the big Nut on the TorqueDrive ? 38 39 ?
39
I would like to buy the frame slider that is on the front wheel of the front disk, can you send me the link for it please? Keep up the good work, thanks!
I am in Korea. If you live in Korea and do not speak Korean, it will be difficult to purchase even if I tell you.
Also, because Korean distributors do not sell overseas,
If you live outside of Korea, purchasing may be difficult.
Also, I don't know of any overseas sellers.
Sorry for not being able to help you
Hello I have a question
I have a honda sh 150i 2022 someone now the clearance of the valves??
That model is not available in Korea. So I don't know.
@@theboy6945 0.4 intake. O.5 exhaust
Может знаете почему при разгоне от 5 до 10 км/ч в вариаторе иногда слышен сильный резкий шум . Хонда форза 350 пробег 2000км. Спасибо.
Это может быть временный шум, вызванный трением между «грузом колодки сцепления» и «внешней частью сцепления» внутри ведомой поверхности трансмиссии.
В этом случае звук может естественным образом исчезнуть по мере дальнейшей езды.
или нет..
Это может быть проблема с «весом колодки сцепления». Однако я думаю, что это не так, потому что пройденный километраж небольшой.
Кроме того, шум может быть вызван вытеканием смазки из сцепления.
Альтернативно, шум может быть вызван попаданием масла на «ведомую поверхность», контактирующую с ремнем.
Поскольку я не открываю и не проверяю ваш мотоцикл самостоятельно,
Трудно сказать, какой именно из них является проблематичным.
Просто для справки
It may be a temporary noise caused by friction between the “clutch shoe weight” and “clutch outer” inside the drivetrain driven face.
In this case, the sound may naturally disappear as you drive more.
or not..
It may be a “clutch shoe weight” issue. However, I think this is not the case because the km traveled is small.
Alternatively, the noise may be caused by grease inside the clutch flowing out.
Alternatively, the noise may be caused by oil being exposed to the "driven face" that contacts the belt.
Since I am not opening and checking your motorcycle myself,
It is difficult to say exactly which one is problematic.
Just for reference
Дорогой друг, спасибо за быстрый ответ. Когда я приезжаю в ХОНДА дилер и говорю им об этой проблеме, то они мне отвечают что всё хорошо. Мотоциклу действует хонда гарантия и хонда не хочет признать проблему. @@MotorcycleRepair
@@tafetdriver281 Мотоцикл еще на гарантии.
Как насчет того, чтобы еще немного поездить на нем, проверить состояние и снова обратиться в сервисный центр Honda?
(Странно, что Хонда говорит, что проблем нет...)
The motorcycle is still under warranty.
How about driving it some more, checking the condition, and contacting the Honda Service Center again?
(It's strange that Honda says there is no problem...)
Дорогой друг, объясню в чём причина. В моей стране холодный климат для мотоциклов. Поэтому мотоциклов продаётся очень немного и механики практически не имеют совсем опыта по ремонту мотоциклов и не знают как это делать. Например в моей стране всего один дилер Хонда и он продаёт очень много автомобилей и всего 15-20 штук мотоциклов разных моделей в год. Когда я взял новый мотоцикл от дилера, то через 20 км потерял переднее стекло, потому что механики не закрепили его как надо. @@MotorcycleRepair
@@tafetdriver281 Эх, на то была причина..
Я думаю, что это действительно прискорбно.
Ah, there was a reason for that..
I think this is truly unfortunate.
통으로 교체하는 게 아니고 슈만 교환이 되는군요?
네 각 파츠별로 상태에 따라 교체를 할수 있습니다.
안녕하세요. 자가정비 해보고싶은데 구동계정비시 필요한 공구좀 알려주시면 감사하겠습니다
기본적으로 8 ~ 32 사이즈의 복스알 세트, 이것을 이용할 라체트, 힌지
그리고 일반적인 일자 십자 드라이버, 정도 있으시면 됩니다.
다만 편리를 위해서 전동 임팩 드라이버가 있으면 좋겠으나...
가격이 20만원이 넘는 것이 아니라면 ..그렇게 오래 사용하지도 못하고 고장날 것이라...
이것의 구매는 심각하게 고민후에 결정하시면 됩니다.
사실...이외에도 정비를 하다보면, 편의를 위해서, 안전을 위해서 필요하게 되는것이 많이 발생합니다.
이 부분은 하시다 보면 본인 욕심에 의해서 또 구매를 하게 될수도 있습니다.
Please what is the starting Music
The background sound is "Arpy - Dan Henig".
슈 교환 하는 이유가 뭔가요?
이 부품은 일정 회전수가 (RPM)이 증가하면,
원심력에 의해 외부로 밀려나면서 뒷바퀴를 회전 시키는 기능을 가졌습니다.
이는 브레이크 패드처럼 어느정도 사용을 하면, 닳아서 기능을 못하게됩니다.
(이때는 알피엠이 올라가도 속도가 나지 않고, 힘이 전달되지 않아 소리만 크고, 제 힘을 낼 수없게 됩니다.)
이정도 되면, 교체를 해주어야 하는 소모품 입니다.
알피엠은 올라가는데...속도가 안난다던지...
언덕을 올라가는데 소리만 크고, 잘 올라가지 않는 현상이 일어나면..
교체시기가 온것이라고 할 수 있습니다.
또한 이것이 문제가 될때.. 구동계 쪽에서 들리지 않던 소음도 발생하는 경우도 있습니다.
為什麼空濾後面的小袋子會有油？
當引擎機油溢出時就會出現這種症狀。偶爾檢查一下是個好主意。
@@MotorcycleRepair 檢查什麼位置？
The trasmition is the same of Honda sh300 2007
Thank you for your comment.
This is de 48000 km service???
no. It was replaced at the request of the motorcycle owner.
You re not torque the nut cvt OMG
Thanks for your comment.
@@AdeArifinIlham-kz8bo do you what is the torque value for tightening the pulley?
오토바이 수리하러 한국에 가고 싶어요
어디에 거주 하고 계신지는 모르겠으나...
그곳에서도 수리 정비는 문제가 없을것이라 보는데 ..
그것이 아닌가요?
that's a big fuker of a belt compared to my Piaggio
Oh, is that so? Thank you for your comment.
SONKI SES NE ACABA
😄
Qué fácil se ve todo!!
Gracias por una buena mirada.
老師傳靠著經驗抓扭力值、鎖死就對了🤣
感謝您的評論。
CHEVERE
thank you 😄