Thank you for your help. All the installation was completed perfectly. I did it by myself whenever I had time, and it took about 5 days. It took at least 3 to 5 hours a day. It took a long time because I did it alone, but I am proud.
Hello my friend. I have peugeot 5008 (2010) model, the cameras that are mounted on the mirrors, should they be on the edge of the mirror? i'm asking you because my mirrors already have a hole in the middle where there is a light, can i put the cameras in there or will there be a problem? thank you very much i am waiting for your reply
I'm doing a 360 degree both side views and front and back soon , no installation video but after it's done , I'll post the finished video when it's all done.
My Android is k2001n T3 will it be compatible with 360.. because when I access the factory settings I see 360 view and 360 thirdparty. But after I save it . And check the app I don't see and 360 app showing on my apps . Is it ok , will the app show only when I connect the cameras to the 12 pin.? Please I need help
Quick view 00:08:Remove the left door trim panel and mirror 01:08:Remove the right door trim panel and mirror 01:24:Remove the rearview camera 02:02:Remove the front camera 02:40:Disassemble the car mirror 04:24:Drilling hole at mirror 05:50:The wire how to through small hole 06:37:Install the mirror back 08:23:How to find trigger wire(The turning light should turn on) 10:16:How to through rear camera wire to front site 10:51:Install front camera 11:20:How to through front camera wire to front site 12:53:Connect the host and interface 13:36:Install the door trim panel back 14:06:Install the side mirror glass 15:56:About calibration tips
First of all, thank you very much for sharing your video. I just have one question; How should I adjust the orientation when connecting right and left cameras? Is there a sensitive setting I should pay attention to?
Hello sir ,the right and left camera view image have 1/3 or 1/4 show car body ,You can watch the video on 360 panoramic calibration on our channel, which contains photos of the viewing angle
So on the radio end of the camera wires, where did you wire the red wires to?? You never showed that. I know the camera end red wires go to turn singles hot wires and the rear goes to back up light hot wire but what about the other red wires? thanks.
Just curious - for what do you need the left/right signal triggers? My Mirror do not have signals and i don't know if it is neccesary to get the signal somewhere else...
Good afternoon . Please tell me I lost the remote from the device a long time ago. yesterday my system stopped being controlled through the screen. how do i do a factory reset? without the remote and pressing the screen. Thank you
@@umuterturk1838 hello ,the signal cable from side mirror turning light is connect with 360 system trigger wire ,not need connect with radio ,only monitor trigger from 360 camera system need connect with radio reverse cable
Hi. I bought this set from you but I don't know how to connect the UART 1 cable. There are two pins. Do you need to provide TX and RX signal from canbus there?
And what signal must be sent to the module to read the speed of the car? Will the module disconnect the transmission of the image from the cameras after turning off the reverse gear or will the image remain for a while when driving forward?
@@robertzakrzewski1642 the trajectory host coming with kind of canbus device ,it can read the car data,like speed ,radar ,door open ,the trajectory line of car ,when finish reverse,the video of 360 system can be set keeping display or screen saver model ,the 360 system always working after car starts
I'm trying to connect the 360 Bird View product to a monitor that only supports HDMI without navigation. Is there anything else I need besides the monitor?
you can using HDMI cable to connect with your monitor ,but first you need a AV monitor to do 360 bird view video output setting to HDMI output ,since default output is CVBS and AHD .
May I ask where did you route the camera wire when you inserted it through the hole of the speaker then through the side door then the door jamb and don’t know where next? How did it get through inside of the car?
Hello, there is a hose between the car door and the body that is used to pass cables. Please refer to the black corrugated pipe in the bottom right corner at the 12th minute and 10th second of the video, which is where it passes through
@@carsanbohi I’m back I removed the rubber on the side of the body but there is a plug and socket connecting all the wires from the door to inside the car. How did you managed to insert the camera wire?
hello. I am planning to purchase and install a 360 Bird View product and connect ACC to power with a fuse. Should I connect to a 10 amp, 15 amp, 20 amp or 30 amp fuse?
hello,you can order this unit at here www.aliexpress.com/item/1005004410841053.html?spm=a2g0o.store_pc_groupList.8148356.11.16557935pk0xQY&pdp_npi=4%40dis%21USD%21US%20%24389.43%21US%20%24260.92%21%21%21389.43%21260.92%21%40212c01e917028930489887113e99ce%2112000029086528971%21sh%21KR%21235089132%21
@@NZphillugnutin6864 www.aliexpress.com/item/3256804220911013.html?pdp_npi=4%40dis%21USD%21US%20%24407.28%21US%20%24249.59%21%21%21407.28%21249.59%21%402136637717223951328122656e0c08%2112000029069694899%21sh%21US%210%21X&spm=a2g0o.store_pc_allItems_or_groupList.new_all_items_2007523739825.1005004407225765 this is 360 system .we dont selling the interface .it need to buy alone
Hello, due to different styles of side mirrors with different internal structures, drilling holes needs to be based on the actual situation of the outer shell. Usually, the position is in the middle of the mirror, and the side cameras have angle pads for angle adjustment, so you don't have to worry too much about installation
hello sir ,you can order here .www.aliexpress.com/item/1005007501137148.html?spm=a2g0o.productlist.main.9.5c24QDD7QDD7lG&algo_pvid=33260d07-47d8-4491-8e67-3a5f83ab882b&algo_exp_id=33260d07-47d8-4491-8e67-3a5f83ab882b-4&pdp_npi=4%40dis%21USD%21188.70%21172.97%21%21%21188.70%21172.97%21%40212a6e3217313155130881138eeda6%2112000041564084561%21sea%21KR%212655962132%21ABX&curPageLogUid=dieixDl6SvYd&utparam-url=scene%3Asearch%7Cquery_from%3A
Thank you for your help. All the installation was completed perfectly. I did it by myself whenever I had time, and it took about 5 days. It took at least 3 to 5 hours a day. It took a long time because I did it alone, but I am proud.
Congratulations，so glad we can help
Hello my friend. I have peugeot 5008 (2010) model, the cameras that are mounted on the mirrors, should they be on the edge of the mirror? i'm asking you because my mirrors already have a hole in the middle where there is a light, can i put the cameras in there or will there be a problem? thank you very much i am waiting for your reply
@@ΕΛΛΑΣγιαΠΑΝΤΑ Hello sir .that's okay .the camera coming with angle rubber normally
I'm doing a 360 degree both side views and front and back soon , no installation video but after it's done , I'll post the finished video when it's all done.
You are very kind 😊,let help more people know 360 system installation
How'd the install go?
@@HAj0698he never did it
My Android is k2001n T3 will it be compatible with 360.. because when I access the factory settings I see 360 view and 360 thirdparty. But after I save it . And check the app I don't see and 360 app showing on my apps . Is it ok , will the app show only when I connect the cameras to the 12 pin.? Please I need help
You're a damn liar Mike
Mastery at its best he did not need to keep on testing to see if it's working in between the process 👌
we advice test the device before installation so we can sure one-stop install
Quick view
00:08:Remove the left door trim panel and mirror
01:08:Remove the right door trim panel and mirror
01:24:Remove the rearview camera
02:02:Remove the front camera
02:40:Disassemble the car mirror
04:24:Drilling hole at mirror
05:50:The wire how to through small hole
06:37:Install the mirror back
08:23:How to find trigger wire(The turning light should turn on)
10:16:How to through rear camera wire to front site
10:51:Install front camera
11:20:How to through front camera wire to front site
12:53:Connect the host and interface
13:36:Install the door trim panel back
14:06:Install the side mirror glass
15:56:About calibration tips
Very professional and clean job. No scratches and very neat wiring work. Congratulations, I just hope you're in the Philippines 🇵🇭
Thanks ❤
First of all, thank you very much for sharing your video. I just have one question; How should I adjust the orientation when connecting right and left cameras? Is there a sensitive setting I should pay attention to?
Hello sir ,the right and left camera view image have 1/3 or 1/4 show car body ,You can watch the video on 360 panoramic calibration on our channel, which contains photos of the viewing angle
Great workmanship.
thanks ,hope this video can help
Need to ask one question about the side mirror that If we hole in side mirror, it void warranty?
We not quite sure about this ,but many new car installed 360 system after sell
So on the radio end of the camera wires, where did you wire the red wires to?? You never showed that. I know the camera end red wires go to turn singles hot wires and the rear goes to back up light hot wire but what about the other red wires? thanks.
Hello ,the other red wire need to connect with radio reverse trigger
For side cam, the red wire to turn signal then how about the other, where should i connect
@@feisal6120 hey ,for rear camera ,it connected with reverse lamp + ,I mean the rear camera trigger wire
One small question where do you connect rear camera trigger wire you are showing the connection but not saying any description of it
Hello rear view camera trigger wire need to connect with reverse lamp +
Does 360 cameras also record for traffic accidents?
yes,it with DVR recorder
Just curious - for what do you need the left/right signal triggers?
My Mirror do not have signals and i don't know if it is neccesary to get the signal somewhere else...
hello sir ,the left and right signal is from car right or left turning light 12V+.not from your mirror screen
@@carsanbo
Yes i know but do i need the signal, when i need the Camera only for parking mode?
I think this signal is only needed during driving?
@@TheOtherArea if you need only for car reverse purpose ,i am advise you just take a reverse system with back up camera only
Where can i connect the white wire on camera? Is it on negative or positive therminal?
If it is the signal trigger line of the camera, it should be connected to the positive pole
@@carsanbo how about the reverse camera?
@@hardyboys1708 it’s same
@@carsanbo thanks a lot men
@@hardyboys1708 you are welcome .hope we can help
But can this process also work on a Mercedes Benz w204 2013 ???
yes
@@saucyiwnl do I have to chnage the screen to an after market one or the follow come screen can work perfectly, just need to buy the cameras ???
@@yahayasojaabubakar7999 you need a headunit that has the 360 system support because it is a chip they need to install into the screen
@@yahayasojaabubakar7999 aliexpress has the cheapest ones I would look for a nice looking 360 display that doesnt leave a corner of ur car not seen
Good afternoon . Please tell me I lost the remote from the device a long time ago. yesterday my system stopped being controlled through the screen. how do i do a factory reset? without the remote and pressing the screen. Thank you
Hello pls order one more remote ,without remote can not doing any setting
Hello, have you connected the signal cable coming from the mirrors to a cable on the radio?
@@umuterturk1838 hello ,the signal cable from side mirror turning light is connect with 360 system trigger wire ,not need connect with radio ,only monitor trigger from 360 camera system need connect with radio reverse cable
Hi. I bought this set from you but I don't know how to connect the UART 1 cable. There are two pins. Do you need to provide TX and RX signal from canbus there?
Hello UART1 is for trajectory host,you need to buy this host alone
And what signal must be sent to the module to read the speed of the car? Will the module disconnect the transmission of the image from the cameras after turning off the reverse gear or will the image remain for a while when driving forward?
@@robertzakrzewski1642 the trajectory host coming with kind of canbus device ,it can read the car data,like speed ,radar ,door open ,the trajectory line of car ,when finish reverse,the video of 360 system can be set keeping display or screen saver model ,the 360 system always working after car starts
I'm trying to connect the 360 Bird View product to a monitor that only supports HDMI without navigation. Is there anything else I need besides the monitor?
you can using HDMI cable to connect with your monitor ,but first you need a AV monitor to do 360 bird view video output setting to HDMI output ,since default output is CVBS and AHD .
Will it work if I just connect the power without connecting the detection wire? Can I use it without connecting the rear left and right blinker wires?
hello ,of course .you can operate by a remote control
I’d love to install this in our 2016 Sienna minivan but I’d want to use the existing screen. Is such a thing possible?
hello .it can be .just need to get a interface
May I ask where did you route the camera wire when you inserted it through the hole of the speaker then through the side door then the door jamb and don’t know where next? How did it get through inside of the car?
Hello, there is a hose between the car door and the body that is used to pass cables. Please refer to the black corrugated pipe in the bottom right corner at the 12th minute and 10th second of the video, which is where it passes through
@@carsanbohi I’m back I removed the rubber on the side of the body but there is a plug and socket connecting all the wires from the door to inside the car. How did you managed to insert the camera wire?
@@dodits1665 hello sir ,please send us the photo to mail box info@carsanbo.com
@@carsanbo ok thanks 🙏
Hi, Can I add 360 camera with OEM lexus es350 2015 radio and keep same back up camera ?
hello sir it can not .OEM radio need to add interface
can you also show how to connect from the camera box to the original screen?
It need a interface device
@@carsanbo do you have interface device for ford ranger?
hello. I am planning to purchase and install a 360 Bird View product and connect ACC to power with a fuse. Should I connect to a 10 amp, 15 amp, 20 amp or 30 amp fuse?
hello sir ,10amp is enought
Thanks for the video. Where should I wire the 2 side cameras if my side mirrors don’t have signal lights? Thanks
hello ,you can get this signal at car fuse box
Will this camera record when parked or driving? Kind of like a dash cam?
yes ,sure .when play at PC .it's split screen with 4 camera video
can you connect 360 camera module (box) to apple carplay module (box)?
hello sir ,if your carplay box have AV IN which support AHD or CVBS input .then okay
@@carsanbo thank you so much
@@dodits1665 ur welcome .if have HDMI input ,also okay
6：03 what did he spray for? lubricant?
yes ,you are right .
Can this be connected to multple screens at once to display panoramic
Our system only support one video output .you can add video amplifier
What is the name of the unit and where can i buy it.. i hope you can help😊
hello,you can order this unit at here www.aliexpress.com/item/1005004410841053.html?spm=a2g0o.store_pc_groupList.8148356.11.16557935pk0xQY&pdp_npi=4%40dis%21USD%21US%20%24389.43%21US%20%24260.92%21%21%21389.43%21260.92%21%40212c01e917028930489887113e99ce%2112000029086528971%21sh%21KR%21235089132%21
How to connect the infrared receiver to the box?
Hello by VGA cable
@@carsanbo thank you. You are the best. Just plug and play right,
@@RashdanBb-eq6nj you need to go to video output setting choose VGA output
Will this work on dodge charger ?
how i can add 360 view in my sienna 2021 original oem radio
Pls check if OEM radio support cvbs input or not ,if yes ,then okay ,and the second option is add the interface
oem radio has 3 28 pin harness i don't knw which is for video middle, side by speaker wire or the last one please reply me thank u@@carsanbo
What do I do if my vehicle doesn’t come with a stereo system to view or monitor the cameras?
Hello sir ,you need to buy a monitor alone ,better with ahd pixel ,our store have stand alone type or mirror type if you don’t like the radio android
Is possible to install 360 system in my tacoma trd sport 2023?
@@CarlosTorres-je3bt hello ,pls check your radio support av in which have cvbs or AHD ,or hdmi input or not ,if yes ,then can be install
@@carsanbo ty my friend ill check
@@CarlosTorres-je3bt okay
Can you please give me the link? I also want to install 360 Birdview on my Lexus RX
hello sir .thanks for your trust .did you have the interface already ?since original car screen need a interface switch LVDS signal to AHD signal
@@carsanbo give me the product link of the one you are installing please.
@@NZphillugnutin6864 www.aliexpress.com/item/3256804220911013.html?pdp_npi=4%40dis%21USD%21US%20%24407.28%21US%20%24249.59%21%21%21407.28%21249.59%21%402136637717223951328122656e0c08%2112000029069694899%21sh%21US%210%21X&spm=a2g0o.store_pc_allItems_or_groupList.new_all_items_2007523739825.1005004407225765
this is 360 system .we dont selling the interface .it need to buy alone
@@carsanbo what interface? Why should I need interface?
@@NZphillugnutin6864 are you using the 360 camera system with the factory radio ?
Hi, How many hours you took to install the 360° car camera system?
hello sir .we take about 3hours to install
Very informative video! Thank you!
you are welcome .so glad we can help
Can you show how side view mirror camera are postioned?
Hello, due to different styles of side mirrors with different internal structures, drilling holes needs to be based on the actual situation of the outer shell. Usually, the position is in the middle of the mirror, and the side cameras have angle pads for angle adjustment, so you don't have to worry too much about installation
@@carsanbo where are the camera lenses facing towards rear or sides ?
@@sj6257 The camera is looking at the side ground at an angle of 180 degrees, allowing the entire side view to be seen
@@carsanbo thank you
Holiao, can you make one for Peugeot 508 2.2 HDi GT station wagon?
Hello sir .our 360 camera system is universal one .just your monitor support CVBS or AHD or HDMI signal input then okay
@@carsanbo what's the highest spec you have?
@@ahafeezs you can conside to take the AI version .its new in this year
I like how the camera in the mirrors that hide not that seen like other brands love it
hello sir .there are have some mirror mould ,but not too much car model have
What is possible problem, when i open driver door but on 360 view show i am opening passenger door?
hello is the CAN BOX software issue ,you need to update the software
你好，美版2017 ES350需要刷机吧？原车屏跟你视频一样小
你好，需要加解码器才能跟360全景连接
Name of the red wire? Tap near speaker
hello sir ,can you tell me the time of video so i can check
大哥 左右的电线接了门那里 然后进去车里面的红色左右电线还需要接哪里
是接转向灯的正极，这个是转向视角触发线
Will it work in XUV700?
Hello sir ,as long as your monitor support then okay
how to get the video footage out of the system ?
There are have a usb memory card for recording video
muchas gracias por el video, tenia la duda si la señal de giro funcionaba al parpadear pero con este video demuestra que si la reconoce.
De nada, el parpadeo del semáforo no afectará la función de activación.
Magknao po labor pa install ng qcy android head with 360 camera?
which apps used ?
Hello sir ,our system not using app ,it can not connect with phone
How can I purchase this system?
hello sir ,you can order here .www.aliexpress.com/item/1005007501137148.html?spm=a2g0o.productlist.main.9.5c24QDD7QDD7lG&algo_pvid=33260d07-47d8-4491-8e67-3a5f83ab882b&algo_exp_id=33260d07-47d8-4491-8e67-3a5f83ab882b-4&pdp_npi=4%40dis%21USD%21188.70%21172.97%21%21%21188.70%21172.97%21%40212a6e3217313155130881138eeda6%2112000041564084561%21sea%21KR%212655962132%21ABX&curPageLogUid=dieixDl6SvYd&utparam-url=scene%3Asearch%7Cquery_from%3A
暑そうｗ でもよく見ると意外と丁寧な仕事で感心。カーサンボのアラウンドビュー製品買うよ！
Yes,its hot when making installation,not a easy job,just contact us if any question,thanks 😊
@@carsanbo
My car is a right-hand drive car with a total length of only 3.4 meters. Will your product work?
@@obamabaraku yes ,it works
Does it fit tucson 2023
Hello sir ,our item is universal,only your radio need support ahd or cvbs signal input
@@carsanbo
Καλησπέρα φίλε μου.
Το Pioneer AVH-Z7200dab μπορεί να υποστηρίξει αυτά τα συστήματα καμερών.;;
Ευχαριστώ εκ των προτέρων.
Tôi đã mua camera của các bạn nhưng không có interface kết nối. Giúp tôi với
which connector you dont have ?it coming with AHD and CVBS RCA output
Why do you need this on a small car
there are have some blind spot there
Great clean job
哈哈哈熟悉的小曲😂
Very nice
thanks
很好👍🏻
Cameras are fitted by cutting the wires, so warranty is void.
You can use a cable free clip for installation, if you are concerned about warranty issues
terrible wiring job, none of it was soldered or securely connected together
Yes ,I am agree with you,if he wraps the connection with a heat shrink tubing ,it will be great
This is so time consuming and required at least 2 skilled professional workers to get the job done properly.
if the first time install .it take times to doing this
I was thinking of adding cameras to my car but never mind it’s a lot of work and probably expensive to hire someone
Yes,it need some shop who have experience doing this ,normally need to take 2-3 hours
Judah Locks
Location nyo sir? ano contact number nyo po
hello sir .we are in Baiyun Guangzhou .please send your inquiry to info@carsanbo.com