I started brainstorming a brass catcher net going into a wet tumbler bucket. Were it not for the sparks and powder around I could stand there all day :-)
I am now on my fourth play-through of this video and I have to say I’m so grateful for the time and effort you have clearly put into this content for us. I have been able to troubleshoot the primer tray, spent-primer collection tube, and stage-two powder-spillage by taking my time through your video and paying close attention to how and why you work in the order you do. Your content is by far the clearest and most comprehensive presentation of the subject matter I’ve found online. You’re easy to understand and easy to follow along with. You helped me pick the right loader, inventory the contents, assemble it, and troubleshoot the issues I’ve encountered with mine. Thank you again.
Wow. I started with a Lee Loader for a 41Mag Blackhawk at my hunting camp on a snowy, dark November night. 40yrs later I still remember the snow over the half frozen pond, woodstove cranking and the smile on my face when I pulled the trigger without blowing up me and the gun like it was yesterday
I have had my Pro 1000 for quite a while and had been very cautous about using it after watching and reading other articles. After seeing your video, I am exited to try again
I have used a Pro 1000 for about 15 years and have found it to be most rewarding and also most frustrating. This video would have made my experience more of the first type and less of the second during the early days. One step I would add, especially when using new brass or range pick-ups is to plunk test the output before going full bore high volume. All brass is not created equal. Some will stick during depriming/resizing and some will seem to be perfect once finished but will not fit into the chamber, causing failures to feed in auto loaders. I now separate brass by head stamp and reset the press when changing brands. Good video. Thanks.
I loved the Pro 1000.. Hadda sell it after my stroke 20 years ago.. Actually had TWO...ONE IN 45 ACP and the other in 9mm...production was insanely fast...the case feed/collator is indispensable!!!
The Lee instructions state the chain go through the "outer-most" hole instead of the inner-most as you have done (@10:45), probably to avoid the chain contacting with the die plate.
Nice video Gavin! I've been using my LEE 1000 since the mid 80's. I've loaded a LOT of 45ACP, 40S&W, 9mm, 357 mag, and 44 mag through that little press. :-) I do use a close-up camera that is about the size of a cigarette mounted on a small bracket to the head, which looks down on the charged brass as it sits in position #3. I can hook up the camera to either my laptop or phone to confirm there is powder in the casing. I also added a primer detector gizmo I made up, with an LED on the body of the press that lights when there is proper seating of the primer. That's saved my butt a few times when I've run out of primers and didn't notice! I've also used the bullet feeder, although at times I just place each bullet by hand since it seems to take more time to stop and load the bullet feeder, than simply grab a bullet and place it by hand on each case. lol
This was a great video. The super nice 4k quality really helps see the fine details. I am getting into reloading and I am basically researching and building up wish lists, so your videos have been a great help!
Lee Pro 1000 was my second press, 1st was the Lee Anniversary kit. In the past 5 years I’ve loaded over 100k on the pro 1000, split between 45ACP for my STI Spartan and 9mm for my CZ SP01. I still use my Anniversary Kit for 223 and 357 mag. In my opinion, Lee is the price performer. Nice to see the improvements on the locking rings and spent primers.
Thank you so much for this video. I'm considering purchase Lee Pro 1000 as my first reloader and this is the most detail and well instructed beginninger guild I ever seem.
What an awesome video. Been wanting my own loader and it looked intimidating when I was researching. A buddy mentioned the Lee press and it looks like a great way to start.
I love my Pro 1k! I added an led halo, which makes visibility great, and I use both the case and bullet feeder. I use this press for, .380, 9mm, .357mag, .45acp, and 7.62x39. I change out the whole shell plate assembly, and turret, for each caliber.
Mike Bolton how much time is involved when switching calibers? I’ve been looking at this reloader, which LEE states it’s “very involved” when switching calibers. Judging from video, if that’s “very involved” then I wonder what easy is.
Love it. I’m getting in to reloading for the first time and I found this press for 200 bucks. I’m doin 9mm lead cast power coated bullets. Can’t wait to start. The goal is .10 cents a round by time I’m done but also descent quality.
Got into reloading after My deployment to Iraq back in 2011. Got the Pro1000 with the classic wooden ball handle. Loved it so much I got 3 more. Glad to see Lee still has the Pro1000 in their line up. Great video, very detailed. Watching you used it makes me want to set mine up again (been in storage the last couple years)
I have to thank you with HUGE thanks for this video. I think it either would have taken me forever to get this setup or maybe not even at all without your directions. My story starts with the machine getting all setup behind me on my workbench and for 5 months it was itching to be used, I waited patiently to finally find primers. Then immediately started setting it up watching your video, which I had found and watched when I first got the machine. Your video is FANTASTIC, the only thing that I wish was more clear was how to choose the die size. I couldnt find anything related to how many grains to use, except for the bullet being 115 grain, but thats not the same measure as the 6 grain number you had on your box. I ended up going to Hornadys website for the bullets and they have a calculator. I weighed it as you showed and realized my scale wasnt accurate enough so I had to buy a new one. Another day later I think I got it and made 10 test rounds. I just hope its correct. I'll test fire them soon. Anyway my story unfortunately doesn't end there. Once I got it all working as you show in the video I decided to add the bullet feeder (btw the casing feeder connection is crap, I think Lee could have easily done better). So I added the bullet feeder. Tested a cycle and the return chain snapped. Gah! I ordered a new one. In the mean time I used a toilet flusher chain, which didnt really work so well. So after adding the bullet feeder I had to recalibrate stage 3 again. I was never able to get the bullet to feed and stapped the toilet chain too. More testing and playing around and making a mess I gave up on the feeders and said, let me just get used to it manually first. So I removed the feeder, recalibrated all 3 stages, put the casing in, lifted it to remove the primer, lowered it and the primer return metal tube came down but the tray did not. I had to pry it off. Little more playing around and figured out that problem, reseated the metal bar or tube whatever you want to call it, tightened the alen screw, recalibrated the die, and was back to testing. New casing, primer wouldnt come out. Lowered the die a little still no dice. After a half an hour of frustration and watching your video over and over, I finally realized the top of the die looked like it was sticking out a little to far, I hammered (carefully) it back down some and I think I'm back in business. Now I just need to wait 2 more days for my return chain :( Moral of the story, get used to a new machine before you try to add to it, and without watching your video 100 times over I think I would have thrown the machine out the window! Well wish me luck, I'll make a few more test rounds once I get it fully working again and give it a shot ;)
I own two Pro 1000s, one for 9 mm and another for 38/357 so I never have to change setup. They work great. Together they were cheaper than a single Dillon 550 or Square Deal for one caliber. Lee made it affordable for me to get into progressive reloading.
@@albatro2676 No, don't use the factory crimp die. That would be preferable but no room in the three die press. Adjusting the bullet seating and crimping die so it crimps enough to hold the bullet firmly but leaves enough case edge exposed to chamber correctly seems to work just fine for both my Glock 19 and CZ SP01.
I just got my press in the mail yesterday. I bought it from Brownell'a for $205 with the .45 ACP dies. It was on backorder andvit's taken 8 months to get it. I'm glad I waited. They're now going for $335 at least. This video is excellent for someone like me who knows next to nothing about reloading. I also have the die set for 300 AAC Blackout (I have 2 rifles and a pistol chambered in 7.62 x 35, so this is gonna be great. My survival plan has always been to have plenty of guns and ammo. With that, I can get anything else I need. I'm pretty sure after watching this video, I'll be pretty good at this. At least I know I won't accidently blow up a car full of kids and water bottles lol!
@@Ultimatereloader did you ever complete the progressive press shootout? I saw the single stage roundup, but I must've missed the progressive shootout.
@@gabe321 If you're going to run rifle through this, it's advised to remove the indexing rod and manually index the shellplate. I run 223 through it and what happens with long-ish rifle (say....anything 2" or longer) is the shellplate will start to index before the bullet is fully out of the seating die. By pulling the rod, you'll be able to fully lower the carrier without the shellplate moving. You can then index by hand.
Great job. I had the Lee 1000 and also loaded .45 ACP. It works great at a good price. I don't load much any more so when I do I use a Lyman Spar-T I've also had many years.
Best video around for setup. I had multiple issues with the damn feeder to the point where I installed a 3v vibrating motor which now feeds about 95% of the time. Tricky to say the least 👍
Recently purchased one of these as an introduction to progressive, using it specifically for 9mm at this stage. Looks like I have the original design, hopefully cycles as well as the updated version. I picked it up for a reasonable price to get me away from single stage loading but couldn't chew the price of a Dillon XL750 just yet. Great video Gavin, your channel and website is a dream compilation of reloading resources!
Roy, I just got one of the old, red base models. Is there some trick to getting the powder system to work. I cannot, for the life of me, get the darn thing to rise with the casing. It just sits there. No movement, no powder. Any advice?
@@bennybarrett01 Hey mate, are you using Lee dies? The case mouth expander (The bit inside the die body) activates the powder measure when the shell plate (With a case in it) reaches full stroke, if you are not seeing any case mouth expansion, you may have to adjust your die downward until you get the desired amount to place a projectile into the mouth without it tipping over, this 'should' solve all your issues. My set-up came with the Auto-disc powder measure, but I have heard of others coming with the drum style powder measure, you may be missing a component? I simply screwed out the top ring of my expander die and replaced it with the powder measure, leaving the insert inside. The top ring that comes installed with the dies out of the box is only if you are using a single stage press. Hope this helps somewhat mate.
I am speechless, loading mag from the press to shooting from inside the shop with a suppressor on a 1911 in .45ACP. How much better can it get. After watching this video, if you are not excited about reloading and shooting, you must me numb. That was a GREAT end to the video!
I’ve used two pro 1000 presses for years , for 32 smith long all the way too 45 colt ,an everything in between. A fine cost effective set up.. takes a little finesse to keep it running trouble free, mostly priming system, keep A can of compressed air handy to keep priming area free of leaking powder, an you’ll be trouble free.. I’ve loaded Thousands of rounds for a small investment
Love your videos. I have the first model from years ago, like the first year they came out because I was too poor for a Dillon and still love it. When I taught my wife to operate it I had to explain that it takes a bit of "feel" when running it. It's set up for 9mm. May have to purchase a new one set for 300blk.
Great video, I’m currently using the Lee Classic Turret, I’ve got a Loadmaster and haven’t set it up yet…I think I’ll pick up the Lee Pro 1000 and gradually get into progressive reloading. Seems like a reasonable step towards the Loadmaster. Thanks again for your very clear videos.
Definitely looking at picking myself up a Lee reloader here soon. Ordered myself their 12g load all. Gonna start saving all my spent ammo into separated containers and take my time looking for deals on things like primers, bullets and powder since everything is going thru the roof here recently
I've been reloading for 45 years. And have never seen a run on ammo and reloading supplies like the last 3 weeks! Lucky I picked up my supplies in early February for 9mm, 10mm and 45 both acp and long Colt. It really depends on how much you shoot as to how long it will take to pay for itself. But it will! My cost for 9mm is 9 cents per round.
I finally got a Lee Loadmaster. It's awesome with the case and bullet feeder. I used to reload with the Lee hand press and it took hours. Now I can reload a range day's worth of ammo an hour before I go to the range. :) It was Gavin who inspired me to think beyond the hand press. His videos made all the difference for me.
I started off with a Lee Pro 1000. Used it for about 6 months and got so frustrated with it I didn't reload for another 7 years. Fast-forward to today and I'm reloading with 3 different Dillon 550B's and an RCBS Rock Chucker. Had I known how much better and easier using the Dillon presses was, I would have spent the extra cash back then and been done with it. It's the old saying, "buy once, cry once". I'm not shitting on Lee presses. If your budget won't ever allow you to get a better press, then, fine. Go ahead and get one. They will do the job. They're just cumbersome and finnicky to use. Especially turret presses. Even though I have to manually index the 550B's, they're MUCH easier to clear a jam or fix a problem when it happens. There's no way to go backwards on the Lee turret presses. Also, getting brass out of the turret when a serious jam happens is next to impossible! Again, buy once, cry once. You really won't regret it!
Very good. Thank you. I shoot a Colt Gold Cup Trophy .45ACP. It will not cycle the rounds unless they have the factory crimp so I have a second die holder for that die then run the whole batch through it. If I knew about the necessity of a factory crimp I would have bought a 4 station loader. I had to move and am having problems getting it set up again. Primer feed and related springs, powder disc too. Do you have troubleshooting videos?
Well that’s a great little press. I’ll never understand why people give it bad reviews because it’s “Lee” I think they make great products for the money. I love mine... some good shooting!
Hi there great Vid, I have had the pro 1000 for about 3 years now , I have 2 presses one in 45 and one in 9mm, the 45 can be very temperamental, but many thousands of rounds later and getting pissed off more than once, I now have it running like a sewing machine and not one duff round , i have pulled so many 45s its not funny before i finally got it running perfect , my 9mm on the other hand has been a lot more smoother, had the odd issue now and then , but have found they need stripping now and then and fully cleaning and oiling and they run fine , just about to start doing 38's and 357, just bought the dies, turret and shell plate so will interesting swapping over , also found the chain system for the powder hopper not that flash , has broken a few times a spring would be better but will modify that in due course .
I think Lee recommends that you run a whole hopper of powder through before trying to meter. This is to coat the inside with graphite from the powder I think. I have an older Pro1000, and have had to fiddle with it a lot to get it working (I inherited it). It is missing the feed tubes so I have to manually feed cases. I have had to disassemble, slightly modify, and tweak the primer feed tube. There has to be a whole stack of primers in there for them to shake down properly; as the supply runs down at the end of a session I have to manually push them as the case presses against the detector. Other than that, it's a pretty solid machine!
I run the loadmaster. It was a challenge getting it dialed in. Lots of primer inconsistencies. Had to get a new primer section from lee. Once you learn its challenges it works but you have to be willing to tinker. I've wondered if other brands are the same
Notice you bumping your head on the case feeder when verifying the powder charge. I find the press light makes it so much easier to see the charge. No more searching the dark hole...
Nice! I started out with the Breech Lock Classic and just recently bought the Load-Master progressive to speed up my pistol and revolver reloading. I still use the BLC for reloading my rifle rounds. I enjoy both very much. I can't wait for the progressive reloading press shootout. I enjoy your videos on reloading and rifle builds very much. This year I think I want to build a 300 PRC, but... the 6XC caught my attention too after watching a David Tubb video.
Just bought a Dillon RL550C to go with my rock chucker but may pick up this lee for a dedicated .45 ACP. By the time I buy more conversions, dies, and a tool head I can pretty much just buy this...
I started with this press too. Im looking into getting something a little better now though. I’m just waiting for your massive progressive press shootout video haha. I’m pretty much gonna get what you like haha.
I was intimidated by the progressive press when I got into reloading a few years ago so I bought a classic turret instead so that I could be more in control and take my time. I wish I would have bought the progressive press now. Lol
Thanks for this video! ALL my reloading equipment is Lee. I started with the single stage about 7 years ago reloading only .223. Quickly added 9mm, .45acp and 7.62x54R. After thousands of rounds, I moved on to Lee’s turret press and currently use that. I also cast my own bullets with Lee molds for all calibers except the .223 (couldn’t get my AR to cycle at the reduced power loads). I never wanted the progressive press because I was concerned about losing some quality control...too many things happening at the same time for me. My main point here is this...I will put my Lee handloads up against any press or system costing 3 or 4 times as much. I’m sick of people looking down on “cheap” Lee equipment when there is nothing wrong at all with it. I see no reason after 10k rounds to “upgrade” to more expensive systems that will get me no better return for my money. I probably still won’t get a progressive press, though. Too easy to get .380 mixed with 9mm, for example. Thanks again!
Great video. Just bought one last week. Waiting for its arrival. Switching gears, I would like to know how to determine the true interior diameter of my Italian made 92A1 barrel. Can't seem to find any info on the web.
I see that you use # 42 on the auto disk for CFE 6.1 grains of powder for 45 cal. Did you check with you powder scale ? I loaded 9mm with CFE , I had to adjust the auto dish up 2 size to 4.6 in grains ? Ty Don
My main gripe with the pro1000 is the 3 stage capability. I feel the 4 stage Breech Lock pro is a better press if you plan on using other die brands. You need an extra powder die to make up for the lack of a powder thru expanding die.
Deprime & size first, then tumble/polish the brass. Now return to the press: Load the clean brass into the case dispenser & (1) clear the flash hole w/o resizing, i.e., by adjusting the Resizing Die or w/ a Universal Decapping Die (2) Then, as normal, expand the case mouth & add powder (3) seat the bullet & finish the round as normal. Yes, specialized Taper Crimp or Roll Crimp may require another step...
Looks like the priming system has been fixed/updated. I had one about 10 years ago and the on press priming was a POS. It caused me to go BLUE. Currently have some dedicated Pro 4000 and now they are coming out with a Pro 6000.
I understand inline probably pays you a bunch of money, but that system would make me crazy! I would go out of my mind with all that flex!! It's probably just me!!
Another upgrade is the fixed indexing pin for the shell plate. In the older model, the shell plate could get very slightly out of adjustment which would cause primers to misfeed.
Ill say this. At least your press in first part was a solid mounted press. In most of the loading videos out there their presses flop around like they couldn't read the instructions that came with their press (no matter what brand). Good show.
Thanks Gavin. I just bought a handgun this year; my first. The wife bought me this Lee Precision Pro 1000. Thanks for the great video. Can't wait to get it unpacked and trying it out. Where can I find a list of all the supplies I need to get started? Thanks
Very nice press. I’m puzzle to see that Lee includes the case feeder plus the fact that it’s a simple and affordable case feeder. Overall, Lee is an excellent brand and good quality for a great price. Too bad Hornady, case feeder is so damn expensive. I refuse to pay Hornady prices for that case feeder. Have someone been able to modified a Lee case feeder to work on the Hornady AP PRESS?? Great video sir.
Please make a few videos on beginner loading or how to start as a beginner. I want to load my own ammo but where I live. Its a learn on your own thing.
I have never used this press. The three die press always confused me until I became a revolver aficionado. The Factory Crimp Die is typically not used for lead boolits in revolvers. The legend goes that only Bigfoot knows how to read the directions on a combination bullet seat & crimp die. Evidently you are hiring him as a consultant for your videos !!! No other way that you could do it. The Lee disk system is based on Richard Lee's belief that Volume is important and weight only needs to be close. There are videos explaining how to accurately calculate the volume of powder that your container / lot is required for a given weight. The VMD in Lee Data is what they were given by the powder companies. It seems wrong to not pe worried about weight so much. Shooting 25 yards with a handgun is not exactly rifle shooting a mile. I do like the use of the handgun as a case gage, primer checker, and powder checker during a session. Of course popping of a magazine every 100 primers does slow down output. Making it fun is why we call this a hobby !!!
"The Factory Crimp Die is typically not used for lead boolits in revolvers" Not sure where you are getting this information. I load lead bullets for .38/.357 and .44 magnum and I use the factory crimp die for every cartridge I load for. The only instance I had a problem was an out of spec carbide ring FCD for .45acp. Sent it to LEE and got it fixed. Works wonderfully now.
I have been having a Lee Pro 100 for over 10 years now. Mostly for loading 9mm for competition shooting. I also have the components to reload .40 .45 & 10mm. I have no idea how many rounds I have loaded on it, and I don’t remember any big issues I have had with the press.
Very fancy, but I can sit on the couch and use my Lee hand press. It's as slow as they come, but I only load 100-200 rounds of .45 ACP at a time. The most affordable way to be a 1911 fanatic. Pretty good upper body workout too.
Great video. Your really stepped through it so it’s easy even for a NOOB like me to understand. I’d like to get into reloading and found this and the 4000 as good options for a starter. They seem to be a better option than the 4 Turret Classic Kit (correct me if I’m wrong). Which would you suggest for a new reloaded given the same price? 1000 or 4000?
Known people to have trouble with powder getting into auto primer feeder. Otherwise have heard good press for $$. Also look for old typewriter stands. Good for presses, and miter (chop) saws plus. Picked several of these out of dumpsters for free and paid $ 50 to $2.00 at garage sales and thrift shops since no one know what they are. Right size for many uses and most have retractavle wheels so they can be moved around.
In Italy we are allowed to have only a max of 200 pistol calibre cartridges unless we specifically request the clearance to have more... basically a single session on this press.
I really tried hard to like the Pro 1000. I'm a big Lee fan boy. I live in Wisconsin so that might help. I had a used one and tried to set it up for 9 mm. The thing kicked my butt! Couldn't seem to get it right. Primer feed issues were the main problem. Tried all the UA-cam hacks to make it run and gave up. Yep I'm a quitter!. Quit smoking, drinking, chasing wild women and now I gave up on the Pro 1000 and got a new lee turret press that I like a lot. I feel more in control and can usually see when something didn't go right. So did Lee fix some of the issues the older 1000's had or is it just me? Been reloading for 40 years and always was satisfied with a single stage press. And then I got into 9 mm semi autos and the ammo gets used up a lot faster than my deer rifle ammo and shotgun shells!! Is the Loadmaster a "big" improvement over the 1000? I'd like to set up for 9 mm and 45 ACP and probably 38 because that's what my kids and I shoot primarily. Sorry for the long %ss reply but you made it look so easy, I felt insecure and had to vent. LOL. Anyone else have problems with these?
Can this Kit be ordered with all the proper die set for the ammo you want to reload or do you have to order them sep? I am also looking to reload .45 acp
Man I would love to shoot from the reloading bench. "Oh, the velocity is a little low. Let me just take the fired case and give it a little bit more powder and shoot it again."
There is one mayor flaw with the Pro 1000, and that is that the powder station is directly above the primer station. I have had issues in the past where for some reason it would not prime the case and then when you charge the case on the down stroke it spills powder all over the primer feeder, not fun! Primers full of powder... For that reason I gave up on the Pro 1000 and would wholeheartedly rather suggest the LoadMaster.
If you are comfortable with what Gavin just showed us, and you are confident you can operate the press, go for this one. My buddy has two of these and they are awesome when they work. Sometimes you need to make little adjustments to keep the press smooth. But IF you go single stage first, you'll eventually end up with a progressive eventually. That's just my opinion. But if you enjoy reloading, there are no bad choices. 👍 Happy reloading.🇺🇸
Yes I use a Lee press for most pistol cartridges and I load .45 acp for both 1911 pistol and Glock 21 pistol for most rifle cartridges I use another system however
First I waould like to Thank you for taking the time to create these vids for us, especially for people like me. I’m really new to the idea of reloading and needless to say, I’m a little intimidated but very interested. Would you create a vid which explains in detail the process of changing this 45 press to 9mm. Again, Thanx for passing along ur knowledge and expertise.
They are so cheap so buy more of them , i have 3 so i can do 38/357 9mm 44spc/44mag it`s the old red one but they work like a charm when set up properly , all complaints of lee machines are from folk`s that can`t adjust them right
Straight from the press into the mag, thru a can and out the door! Living the high life my friend! 🇺🇸
I need to make a T-Shirt with that slogan on it!!!!
gavintoobe I own a screen printing and embroidery shop, if you ever need anything please let me know!! Love your videos!
I started brainstorming a brass catcher net going into a wet tumbler bucket. Were it not for the sparks and powder around I could stand there all day :-)
I am now on my fourth play-through of this video and I have to say I’m so grateful for the time and effort you have clearly put into this content for us. I have been able to troubleshoot the primer tray, spent-primer collection tube, and stage-two powder-spillage by taking my time through your video and paying close attention to how and why you work in the order you do. Your content is by far the clearest and most comprehensive presentation of the subject matter I’ve found online. You’re easy to understand and easy to follow along with. You helped me pick the right loader, inventory the contents, assemble it, and troubleshoot the issues I’ve encountered with mine. Thank you again.
Wow. I started with a Lee Loader for a 41Mag Blackhawk at my hunting camp on a snowy, dark November night. 40yrs later I still remember the snow over the half frozen pond, woodstove cranking and the smile on my face when I pulled the trigger without blowing up me and the gun like it was yesterday
I have had my Pro 1000 for quite a while and had been very cautous about using it after watching and reading other articles. After seeing your video, I am exited to try again
I have used a Pro 1000 for about 15 years and have found it to be most rewarding and also most frustrating. This video would have made my experience more of the first type and less of the second during the early days. One step I would add, especially when using new brass or range pick-ups is to plunk test the output before going full bore high volume. All brass is not created equal. Some will stick during depriming/resizing and some will seem to be perfect once finished but will not fit into the chamber, causing failures to feed in auto loaders. I now separate brass by head stamp and reset the press when changing brands. Good video. Thanks.
Love the workshop with the rail mount for press storage, knee mill, lathe, and integrated firing range from the reloading table. Slick AF
Sweet! A real man cave if I’ve ever seen one.
I loved the Pro 1000..
Hadda sell it after my stroke 20 years ago..
Actually had TWO...ONE IN
45 ACP and the other in 9mm...production was insanely fast...the case feed/collator is indispensable!!!
I'm hooked on reloading on. I want to buy and start reloading for my hobby, now can't find now supplies due to pandemic. The hell with you Covid-19!!
I bought my first 1000 30 years ago,I like how they rotated the base on these!
I have watched this video about 50 times to help me set my press up. Thank you for all the help.
Always great, I’m grateful that you made these great tutorials. I’m going to start reloading after years of not doing it. Thank you
Glad to help
The Lee instructions state the chain go through the "outer-most" hole instead of the inner-most as you have done (@10:45), probably to avoid the chain contacting with the die plate.
Nice video Gavin! I've been using my LEE 1000 since the mid 80's. I've loaded a LOT of 45ACP, 40S&W, 9mm, 357 mag, and 44 mag through that little press. :-) I do use a close-up camera that is about the size of a cigarette mounted on a small bracket to the head, which looks down on the charged brass as it sits in position #3. I can hook up the camera to either my laptop or phone to confirm there is powder in the casing. I also added a primer detector gizmo I made up, with an LED on the body of the press that lights when there is proper seating of the primer. That's saved my butt a few times when I've run out of primers and didn't notice! I've also used the bullet feeder, although at times I just place each bullet by hand since it seems to take more time to stop and load the bullet feeder, than simply grab a bullet and place it by hand on each case. lol
Would like more info on your primer detection.
This was a great video. The super nice 4k quality really helps see the fine details. I am getting into reloading and I am basically researching and building up wish lists, so your videos have been a great help!
Glad it was helpful!
Lee Pro 1000 was my second press, 1st was the Lee Anniversary kit. In the past 5 years I’ve loaded over 100k on the pro 1000, split between 45ACP for my STI Spartan and 9mm for my CZ SP01. I still use my Anniversary Kit for 223 and 357 mag. In my opinion, Lee is the price performer. Nice to see the improvements on the locking rings and spent primers.
Have the SP 01 also.... Loves 124g. Over 4.1 of N320. Probably 20k thru the classic turret press
Thank you so much for this video. I'm considering purchase Lee Pro 1000 as my first reloader and this is the most detail and well instructed beginninger guild I ever seem.
Great therapy for the times being what they are. Always enjoy your videos, a must see for any reloader
Regardless of which brand he unboxes, I find myself wanting every single press he demonstrates for us...
I want like every press I see😂 but I don’t even reload that much only when I pay kids to pick up brass😂
That’s two of us😂
What an awesome video. Been wanting my own loader and it looked intimidating when I was researching. A buddy mentioned the Lee press and it looks like a great way to start.
I love my Pro 1k! I added an led halo, which makes visibility great, and I use both the case and bullet feeder. I use this press for, .380, 9mm, .357mag,
.45acp, and 7.62x39. I change out the whole shell plate assembly, and turret, for each caliber.
Mike Bolton how much time is involved when switching calibers? I’ve been looking at this reloader, which LEE states it’s “very involved” when switching calibers. Judging from video, if that’s “very involved” then I wonder what easy is.
Love it. I’m getting in to reloading for the first time and I found this press for 200 bucks. I’m doin 9mm lead cast power coated bullets. Can’t wait to start. The goal is .10 cents a round by time I’m done but also descent quality.
Got into reloading after My deployment to Iraq back in 2011. Got the Pro1000 with the classic wooden ball handle. Loved it so much I got 3 more. Glad to see Lee still has the Pro1000 in their line up. Great video, very detailed. Watching you used it makes me want to set mine up again (been in storage the last couple years)
I have to thank you with HUGE thanks for this video. I think it either would have taken me forever to get this setup or maybe not even at all without your directions. My story starts with the machine getting all setup behind me on my workbench and for 5 months it was itching to be used, I waited patiently to finally find primers. Then immediately started setting it up watching your video, which I had found and watched when I first got the machine. Your video is FANTASTIC, the only thing that I wish was more clear was how to choose the die size. I couldnt find anything related to how many grains to use, except for the bullet being 115 grain, but thats not the same measure as the 6 grain number you had on your box. I ended up going to Hornadys website for the bullets and they have a calculator. I weighed it as you showed and realized my scale wasnt accurate enough so I had to buy a new one. Another day later I think I got it and made 10 test rounds. I just hope its correct. I'll test fire them soon. Anyway my story unfortunately doesn't end there. Once I got it all working as you show in the video I decided to add the bullet feeder (btw the casing feeder connection is crap, I think Lee could have easily done better). So I added the bullet feeder. Tested a cycle and the return chain snapped. Gah! I ordered a new one. In the mean time I used a toilet flusher chain, which didnt really work so well. So after adding the bullet feeder I had to recalibrate stage 3 again. I was never able to get the bullet to feed and stapped the toilet chain too. More testing and playing around and making a mess I gave up on the feeders and said, let me just get used to it manually first. So I removed the feeder, recalibrated all 3 stages, put the casing in, lifted it to remove the primer, lowered it and the primer return metal tube came down but the tray did not. I had to pry it off. Little more playing around and figured out that problem, reseated the metal bar or tube whatever you want to call it, tightened the alen screw, recalibrated the die, and was back to testing. New casing, primer wouldnt come out. Lowered the die a little still no dice. After a half an hour of frustration and watching your video over and over, I finally realized the top of the die looked like it was sticking out a little to far, I hammered (carefully) it back down some and I think I'm back in business. Now I just need to wait 2 more days for my return chain :( Moral of the story, get used to a new machine before you try to add to it, and without watching your video 100 times over I think I would have thrown the machine out the window! Well wish me luck, I'll make a few more test rounds once I get it fully working again and give it a shot ;)
I love the press, .45 acp, the 1911, and Springfield xd45
I own two Pro 1000s, one for 9 mm and another for 38/357 so I never have to change setup. They work great. Together they were cheaper than a single Dillon 550 or Square Deal for one caliber. Lee made it affordable for me to get into progressive reloading.
Do you need to use de FCD for 9 mm ? Or it's not necessary ?
@@albatro2676 No, don't use the factory crimp die. That would be preferable but no room in the three die press. Adjusting the bullet seating and crimping die so it crimps enough to hold the bullet firmly but leaves enough case edge exposed to chamber correctly seems to work just fine for both my Glock 19 and CZ SP01.
@@chiltonweems1357 What are your thoughts about the Lee BLP ?
I just got my press in the mail yesterday. I bought it from Brownell'a for $205 with the .45 ACP dies. It was on backorder andvit's taken 8 months to get it. I'm glad I waited. They're now going for $335 at least. This video is excellent for someone like me who knows next to nothing about reloading. I also have the die set for 300 AAC Blackout (I have 2 rifles and a pistol chambered in 7.62 x 35, so this is gonna be great. My survival plan has always been to have plenty of guns and ammo. With that, I can get anything else I need. I'm pretty sure after watching this video, I'll be pretty good at this. At least I know I won't accidently blow up a car full of kids and water bottles lol!
Can't wait for the progressive press shootout/comparison!
It'll be cool, and a LOT of work for me... :) :) but I love me work, so no complaining here
Me either! I'm looking for a good progressive to get into reloading with and will DEFINITELY be watching that video when it comes our.
@@Ultimatereloader did you ever complete the progressive press shootout? I saw the single stage roundup, but I must've missed the progressive shootout.
Lee makes some great products. Thanks for sharing
I just bought the Lee hand press to start off I think I’m going to get this for my 45 ACP and my 308 with 5.56.
@@gabe321
If you're going to run rifle through this, it's advised to remove the indexing rod and manually index the shellplate.
I run 223 through it and what happens with long-ish rifle (say....anything 2" or longer) is the shellplate will start to index before the bullet is fully out of the seating die. By pulling the rod, you'll be able to fully lower the carrier without the shellplate moving. You can then index by hand.
the BEST video on UA-cam! (The ammo test made it!!)
21:21
Ian is weeping softly in the distance at the thought of a spinner target.
Great job. I had the Lee 1000 and also loaded .45 ACP. It works great at a good price. I don't load much any more so when I do I use a Lyman Spar-T I've also had many years.
Best video around for setup. I had multiple issues with the damn feeder to the point where I installed a 3v vibrating motor which now feeds about 95% of the time. Tricky to say the least 👍
Recently purchased one of these as an introduction to progressive, using it specifically for 9mm at this stage. Looks like I have the original design, hopefully cycles as well as the updated version. I picked it up for a reasonable price to get me away from single stage loading but couldn't chew the price of a Dillon XL750 just yet. Great video Gavin, your channel and website is a dream compilation of reloading resources!
Roy, I just got one of the old, red base models. Is there some trick to getting the powder system to work. I cannot, for the life of me, get the darn thing to rise with the casing. It just sits there. No movement, no powder. Any advice?
@@bennybarrett01 Hey mate, are you using Lee dies? The case mouth expander (The bit inside the die body) activates the powder measure when the shell plate (With a case in it) reaches full stroke, if you are not seeing any case mouth expansion, you may have to adjust your die downward until you get the desired amount to place a projectile into the mouth without it tipping over, this 'should' solve all your issues. My set-up came with the Auto-disc powder measure, but I have heard of others coming with the drum style powder measure, you may be missing a component? I simply screwed out the top ring of my expander die and replaced it with the powder measure, leaving the insert inside. The top ring that comes installed with the dies out of the box is only if you are using a single stage press. Hope this helps somewhat mate.
I am speechless, loading mag from the press to shooting from inside the shop with a suppressor on a 1911 in .45ACP. How much better can it get.
After watching this video, if you are not excited about reloading and shooting, you must me numb. That was a
GREAT end to the video!
Haha- glad you enjoyed it Paul! This is what true freedom looks like, and I am super-grateful to be able to live this lifestyle!!!!!
Very well said
I’d like to see you review the APP press
I just my 9mm kit today. I had one about 20 years ago that I gave to a friend and it worked well.
I’ve used two pro 1000 presses for years , for 32 smith long all the way too 45 colt ,an everything in between.
A fine cost effective set up.. takes a little finesse to keep it running trouble free, mostly priming system, keep
A can of compressed air handy to keep priming area free of leaking powder, an you’ll be trouble free.. I’ve loaded
Thousands of rounds for a small investment
Shooting ammo from the tray, behind the bench. Just pick up and reload again! Love it!
Love your videos. I have the first model from years ago, like the first year they came out because I was too poor for a Dillon and still love it. When I taught my wife to operate it I had to explain that it takes a bit of "feel" when running it. It's set up for 9mm. May have to purchase a new one set for 300blk.
Great video, I’m currently using the Lee Classic Turret, I’ve got a Loadmaster and haven’t set it up yet…I think I’ll pick up the Lee Pro 1000 and gradually get into progressive reloading. Seems like a reasonable step towards the Loadmaster. Thanks again for your very clear videos.
Definitely looking at picking myself up a Lee reloader here soon. Ordered myself their 12g load all. Gonna start saving all my spent ammo into separated containers and take my time looking for deals on things like primers, bullets and powder since everything is going thru the roof here recently
I've been reloading for 45 years. And have never seen a run on ammo and reloading supplies like the last 3 weeks! Lucky I picked up my supplies in early February for 9mm, 10mm and 45 both acp and long Colt. It really depends on how much you shoot as to how long it will take to pay for itself. But it will! My cost for 9mm is 9 cents per round.
I finally got a Lee Loadmaster. It's awesome with the case and bullet feeder. I used to reload with the Lee hand press and it took hours. Now I can reload a range day's worth of ammo an hour before I go to the range. :) It was Gavin who inspired me to think beyond the hand press. His videos made all the difference for me.
I started off with a Lee Pro 1000. Used it for about 6 months and got so frustrated with it I didn't reload for another 7 years. Fast-forward to today and I'm reloading with 3 different Dillon 550B's and an RCBS Rock Chucker. Had I known how much better and easier using the Dillon presses was, I would have spent the extra cash back then and been done with it. It's the old saying, "buy once, cry once".
I'm not shitting on Lee presses. If your budget won't ever allow you to get a better press, then, fine. Go ahead and get one. They will do the job. They're just cumbersome and finnicky to use. Especially turret presses.
Even though I have to manually index the 550B's, they're MUCH easier to clear a jam or fix a problem when it happens. There's no way to go backwards on the Lee turret presses. Also, getting brass out of the turret when a serious jam happens is next to impossible!
Again, buy once, cry once. You really won't regret it!
Very nice demo...I must say..the tube feeder for the cases is a novel and simple idea..
The Pro 1000 was my first progressive press..actually TWO Pro 1000s...both.used
I wrap my powder measure at the lid area with blue painters tape for a slightly snug fit
Very good. Thank you. I shoot a Colt Gold Cup Trophy .45ACP. It will not cycle the rounds unless they have the factory crimp so I have a second die holder for that die then run the whole batch through it. If I knew about the necessity of a factory crimp I would have bought a 4 station loader.
I had to move and am having problems getting it set up again. Primer feed and related springs, powder disc too.
Do you have troubleshooting videos?
I used to have TWO of therm....bought both used...loved them - wound up selling both aftrer my stroke 20 years ago and sorry I did
Well that’s a great little press. I’ll never understand why people give it bad reviews because it’s “Lee” I think they make great products for the money. I love mine... some good shooting!
I always liked the Auto Disk setup Lee has, especially for small charges. Great review Gavin.
wow they finally thought about where the spent primers go. the old one is such a pain to get the old primers out as it drops into the base.
Hi there great Vid, I have had the pro 1000 for about 3 years now , I have 2 presses one in 45 and one in 9mm, the 45 can be very temperamental, but many thousands of rounds later and getting pissed off more than once, I now have it running like a sewing machine and not one duff round , i have pulled so many 45s its not funny before i finally got it running perfect , my 9mm on the other hand has been a lot more smoother, had the odd issue now and then , but have found they need stripping now and then and fully cleaning and oiling and they run fine , just about to start doing 38's and 357, just bought the dies, turret and shell plate so will interesting swapping over , also found the chain system for the powder hopper not that flash , has broken a few times a spring would be better but will modify that in due course .
I think Lee recommends that you run a whole hopper of powder through before trying to meter. This is to coat the inside with graphite from the powder I think. I have an older Pro1000, and have had to fiddle with it a lot to get it working (I inherited it). It is missing the feed tubes so I have to manually feed cases. I have had to disassemble, slightly modify, and tweak the primer feed tube. There has to be a whole stack of primers in there for them to shake down properly; as the supply runs down at the end of a session I have to manually push them as the case presses against the detector. Other than that, it's a pretty solid machine!
I don't think so, too much work.
I run the loadmaster. It was a challenge getting it dialed in. Lots of primer inconsistencies. Had to get a new primer section from lee. Once you learn its challenges it works but you have to be willing to tinker. I've wondered if other brands are the same
Notice you bumping your head on the case feeder when verifying the powder charge. I find the press light makes it so much easier to see the charge. No more searching the dark hole...
You know I was thinking the same thing!
@@kmssquared LOL!
KMS Squared waiting for a light set specifically designed for the pro 1000 🤔
@@davids5956 We have one. The UFO LT shop.kmssquared.com/shop?olsPage=products%2Fufo-lt
Great video! This maybe my first reloading press. Thanks so much for sharing.
Nice! I started out with the Breech Lock Classic and just recently bought the Load-Master progressive to speed up my pistol and revolver reloading. I still use the BLC for reloading my rifle rounds. I enjoy both very much. I can't wait for the progressive reloading press shootout. I enjoy your videos on reloading and rifle builds very much. This year I think I want to build a 300 PRC, but... the 6XC caught my attention too after watching a David Tubb video.
Just bought a Dillon RL550C to go with my rock chucker but may pick up this lee for a dedicated .45 ACP. By the time I buy more conversions, dies, and a tool head I can pretty much just buy this...
I started with this press too. Im looking into getting something a little better now though. I’m just waiting for your massive progressive press shootout video haha. I’m pretty much gonna get what you like haha.
I was intimidated by the progressive press when I got into reloading a few years ago so I bought a classic turret instead so that I could be more in control and take my time. I wish I would have bought the progressive press now. Lol
Don't worry, you can't have "too many" presses :)
Definitely recommend using a powder baffle in the autocharge. Makes it quite consistent.
Awesome video and review as usual. Thanks Gavin!
Thanks!
Thanks for this video! ALL my reloading equipment is Lee. I started with the single stage about 7 years ago reloading only .223. Quickly added 9mm, .45acp and 7.62x54R. After thousands of rounds, I moved on to Lee’s turret press and currently use that. I also cast my own bullets with Lee molds for all calibers except the .223 (couldn’t get my AR to cycle at the reduced power loads). I never wanted the progressive press because I was concerned about losing some quality control...too many things happening at the same time for me. My main point here is this...I will put my Lee handloads up against any press or system costing 3 or 4 times as much. I’m sick of people looking down on “cheap” Lee equipment when there is nothing wrong at all with it. I see no reason after 10k rounds to “upgrade” to more expensive systems that will get me no better return for my money. I probably still won’t get a progressive press, though. Too easy to get .380 mixed with 9mm, for example. Thanks again!
The lee turret presses are very good and very useful tools.
Great video. Just bought one last week. Waiting for its arrival. Switching gears, I would like to know how to determine the true interior diameter of my Italian made 92A1 barrel. Can't seem to find any info on the web.
I see that you use # 42 on the auto disk for CFE 6.1 grains of powder for 45 cal. Did you check with you powder scale ? I loaded 9mm with CFE , I had to adjust the auto dish up 2 size to 4.6 in grains ? Ty Don
He shows in the video checking a filled case on a scale.
My main gripe with the pro1000 is the 3 stage capability. I feel the 4 stage Breech Lock pro is a better press if you plan on using other die brands. You need an extra powder die to make up for the lack of a powder thru expanding die.
VIDEO COMING!!!!! (and BTW: that's why I upgraded from my LEE Pro 1000 originally- for 4+ stations :) ).
Deprime & size first, then tumble/polish the brass. Now return to the press: Load the clean brass into the case dispenser & (1) clear the flash hole w/o resizing, i.e., by adjusting the Resizing Die or w/ a Universal Decapping Die (2) Then, as normal, expand the case mouth & add powder (3) seat the bullet & finish the round as normal. Yes, specialized Taper Crimp or Roll Crimp may require another step...
Looks like the priming system has been fixed/updated. I had one about 10 years ago and the on press priming was a POS. It caused me to go BLUE. Currently have some dedicated Pro 4000 and now they are coming out with a Pro 6000.
.45 A.C.P. 1911 is good for me Awesome demonstration bud
I understand inline probably pays you a bunch of money, but that system would make me crazy!
I would go out of my mind with all that flex!!
It's probably just me!!
How about the height! it's ridiculously high for any amount of extended use. Has to be crazy uncomfortable.
Another upgrade is the fixed indexing pin for the shell plate. In the older model, the shell plate could get very slightly out of adjustment which would cause primers to misfeed.
Exactly- that was really the only trouble I had with my first Pro 1000, and the pin indexing has fixed that....
Great video, I need a progressive press for pistol reloading, this was a great review and setup vid. Thanks
Ill say this. At least your press in first part was a solid mounted press. In most of the loading videos out there their presses flop around like they couldn't read the instructions that came with their press (no matter what brand). Good show.
AKWAYS gotta make a dummy round for each bullet/style of bullet you load...makes setup between calibers so much easier
Really great video here! You've got a great channel here!
Thanks Gavin. I just bought a handgun this year; my first. The wife bought me this Lee Precision Pro 1000. Thanks for the great video. Can't wait to get it unpacked and trying it out. Where can I find a list of all the supplies I need to get started? Thanks
Tell us more about that bench your setup on. It looks very interesting. Thanks for the video.
Very nice press. I’m puzzle to see that Lee includes the case feeder plus the fact that it’s a simple and affordable case feeder. Overall, Lee is an excellent brand and good quality for a great price. Too bad Hornady, case feeder is so damn expensive. I refuse to pay Hornady prices for that case feeder. Have someone been able to modified a Lee case feeder to work on the Hornady AP PRESS?? Great video sir.
Please make a few videos on beginner loading or how to start as a beginner. I want to load my own ammo but where I live. Its a learn on your own thing.
Thank you thank you Gavin just what I needed.
Awesome! What’s beyond that target though? Hopefully a berm and a locked gate and not the Amazon driver turning the corner up the drive
I have never used this press. The three die press always confused me until I became a revolver aficionado. The Factory Crimp Die is typically not used for lead boolits in revolvers.
The legend goes that only Bigfoot knows how to read the directions on a combination bullet seat & crimp die. Evidently you are hiring him as a consultant for your videos !!! No other way that you could do it.
The Lee disk system is based on Richard Lee's belief that Volume is important and weight only needs to be close. There are videos explaining how to accurately calculate the volume of powder that your container / lot is required for a given weight. The VMD in Lee Data is what they were given by the powder companies. It seems wrong to not pe worried about weight so much. Shooting 25 yards with a handgun is not exactly rifle shooting a mile.
I do like the use of the handgun as a case gage, primer checker, and powder checker during a session. Of course popping of a magazine every 100 primers does slow down output. Making it fun is why we call this a hobby !!!
"The Factory Crimp Die is typically not used for lead boolits in revolvers"
Not sure where you are getting this information. I load lead bullets for .38/.357 and .44 magnum and I use the factory crimp die for every cartridge I load for. The only instance I had a problem was an out of spec carbide ring FCD for .45acp. Sent it to LEE and got it fixed. Works wonderfully now.
I have been having a Lee Pro 100 for over 10 years now. Mostly for loading 9mm for competition shooting. I also have the components to reload .40 .45 & 10mm. I have no idea how many rounds I have loaded on it, and I don’t remember any big issues I have had with the press.
I think this is the closest to showing complete die set ups you have shown so far!
Very fancy, but I can sit on the couch and use my Lee hand press. It's as slow as they come, but I only load 100-200 rounds of .45 ACP at a time. The most affordable way to be a 1911 fanatic. Pretty good upper body workout too.
Great video. Your really stepped through it so it’s easy even for a NOOB like me to understand. I’d like to get into reloading and found this and the 4000 as good options for a starter. They seem to be a better option than the 4 Turret Classic Kit (correct me if I’m wrong). Which would you suggest for a new reloaded given the same price? 1000 or 4000?
Known people to have trouble with powder getting into auto primer feeder. Otherwise have heard good press for $$. Also look for old typewriter stands. Good for presses, and miter (chop) saws plus. Picked several of these out of dumpsters for free and paid $ 50 to $2.00 at garage sales and thrift shops since no one know what they are. Right size for many uses and most have retractavle wheels so they can be moved around.
WoW didn't think the Pro 1000 was that slick. 45 acp is my goto range fun.
In Italy we are allowed to have only a max of 200 pistol calibre cartridges unless we specifically request the clearance to have more... basically a single session on this press.
I really tried hard to like the Pro 1000. I'm a big Lee fan boy. I live in Wisconsin so that might help. I had a used one and tried to set it up for 9 mm. The thing kicked my butt! Couldn't seem to get it right. Primer feed issues were the main problem. Tried all the UA-cam hacks to make it run and gave up. Yep I'm a quitter!. Quit smoking, drinking, chasing wild women and now I gave up on the Pro 1000 and got a new lee turret press that I like a lot. I feel more in control and can usually see when something didn't go right. So did Lee fix some of the issues the older 1000's had or is it just me? Been reloading for 40 years and always was satisfied with a single stage press. And then I got into 9 mm semi autos and the ammo gets used up a lot faster than my deer rifle ammo and shotgun shells!! Is the Loadmaster a "big" improvement over the 1000? I'd like to set up for 9 mm and 45 ACP and probably 38 because that's what my kids and I shoot primarily. Sorry for the long %ss reply but you made it look so easy, I felt insecure and had to vent. LOL. Anyone else have problems with these?
Can this Kit be ordered with all the proper die set for the ammo you want to reload or do you have to order them sep? I am also looking to reload .45 acp
So does this loader not deprime the brass?
Thinking about buying one.
Very nice video, I’m looking in to a Lee 4000 progressive
I put a cardboard baffle in the powder vessel, fixed inconsistent drop amount once it gets below 50%
Are you planning a video on the NEW 2023 Pro 1000 9mm Press?
Man I would love to shoot from the reloading bench.
"Oh, the velocity is a little low. Let me just take the fired case and give it a little bit more powder and shoot it again."
I was thinking the same 😂
There is one mayor flaw with the Pro 1000, and that is that the powder station is directly above the primer station. I have had issues in the past where for some reason it would not prime the case and then when you charge the case on the down stroke it spills powder all over the primer feeder, not fun! Primers full of powder...
For that reason I gave up on the Pro 1000 and would wholeheartedly rather suggest the LoadMaster.
Wow check your privilege 🤣🤣🤣
Thanks for the awesome video, going to pick one of these up, or should I start with a single stage?
If you are comfortable with what Gavin just showed us, and you are confident you can operate the press, go for this one. My buddy has two of these and they are awesome when they work. Sometimes you need to make little adjustments to keep the press smooth. But IF you go single stage first, you'll eventually end up with a progressive eventually. That's just my opinion. But if you enjoy reloading, there are no bad choices. 👍 Happy reloading.🇺🇸
Yes I use a Lee press for most pistol cartridges and I load .45 acp for both 1911 pistol and Glock 21 pistol for most rifle cartridges I use another system however
First I waould like to Thank you for taking the time to create these vids for us, especially for people like me. I’m really new to the idea of reloading and needless to say, I’m a little intimidated but very interested. Would you create a vid which explains in detail the process of changing this 45 press to 9mm.
Again, Thanx for passing along ur knowledge and expertise.
They are so cheap so buy more of them , i have 3 so i can do 38/357 9mm 44spc/44mag it`s the old red one but they work like a charm when set up properly , all complaints of lee machines are from folk`s that can`t adjust them right