Configure Altivar ATV320 Drive for 3-Preset Speeds!!देखें 3 अलग अलग Speeds पे केसे Motor Run करें.

[@Sanataniboy22970]

Slow and fast speed mein reverse and Forward kaise chalate h please reply sir
Break (thrastar type) assemble aur operate kaise karte h

[@rajeshkumargupta661]

Sir, what happen when switch on all selector switch ??

[@usmanahmed9929]

Slow and fast speed mein reverse and Forward kaise chalate h
please reply sir

[@manojhanda3726]

Paji Saadi Schneider di vfd 3.7 kw 5 hp single face di hai motor virdi cle, di hai slow ram yani 100 rpm cha lord nahi ley Rahi please j tusi kuch upaay dasoo , sayad saadey too programing sahi nahi ho rahi

[@gajendrprasadgupta7482]

Sheniader ATV 312 vfd ka jog (inch) mode kaun sa paramiter please helf mi sir

[@jonasyulledesouzayulle]

Boa noite felicidade paz grand invent union pacific e fundamental energia infinita. Legal Chow fantástico.

[@Brijesh8080]

Very Nice.
please make video on PID controller with internal set point and feedback from Potentiometer in ATV 320.

[@j.s.electricalinstrumentat2146]

Ok

[@pk_Yadav-kq6gw]

Mast hai Bhai 🎉

[@kashifkashif7934]

r1 r2 ki sitting kesy kra ga brak open k liya

[@surajkadam7845]

Altivar 320 sof problem Aya hai vfd change karane k bad breaking resistance bhi joda Hain kaise thik kare

[@manidhaliwal8017]

Nyc sardar ji 👏

[@radheradhe11193]

Bauth ache se batae ho

[@j.s.electricalinstrumentat2146]

Thanks

[@jitendradubey8022]

Mst h sir

[@RaviSharma-xi4ly]

Very nice information sardar ji

[@j.s.electricalinstrumentat2146]

Thanks for watching video

[@abubackerpt9438]

Step type rotary selector switch is better than single single selector switch s

[@YOGESHSINGHDASILAKAMSHYARGHATI]

Forward & reverse में भी चलाओ

[@Ramtecheasy143]

3 selectors ek sath on krke dikhaiye

[@Thesongtv123]

कृपया ATV 312 0.37KW. के बारे मेंपैरामीटर्स एवं वायरिंग की जानकारी हिन्दी में बतावें

[@anandtidke378]

Sir motor run me hz25 50hz karna hai

[@j.s.electricalinstrumentat2146]

In program set maximum frequency 50hz

[@SHIVKUMAR-yu7gu]

Pol kis perametor me hote he

[@j.s.electricalinstrumentat2146]

Dear Shiv, In ATV320 drive, we can set only MOTOR SPEED IN drc group in nsp( Rated Motor Speed) parameter

[@Abhi_asthetics]

Sir DCS or Drive me communication kaise karte hai

[@kuttu45454]

How to change jog dial into rpm controller

[@babu-di7oi]

👌👌👌

[@j.s.electricalinstrumentat2146]

Thanks

[@sandeepverma8091]

Aapne ye nhii bataya pehla selector switch on rehne do or dusra selector switch on karo to kya hoga ......aapne ye to bataya nhii 2 preset speed 2 speed ka combination banana padega,4 preset speed mein 4 speed combination .....

[@allknowledgeinhindi468]

Aisa manual kaise milega

[@indratamang7120]

Why my VFD is displaying nLP? checked input Voltage and its showing 415V. and bus voltage is 345V. but its not running .

[@j.s.electricalinstrumentat2146]

If NLP state does not change with correct voltage present on L1, L2, & L3, remove the control board and check for loose connections of ribbon cables inside the drive.
WARNING: This step should be performed while the drive is powered down, and proper personal protective equipment should be worn.

[@indratamang7120]

@@j.s.electricalinstrumentat2146 thank you for the suggestion

[@razaullah4338]

Whith out off s w 1 or 2it bosibal to jump to or third speed oprationg

[@NewsAap-s2r]

Good

[@j.s.electricalinstrumentat2146]

Thanks

[@NagendraSingh-zv8ut]

320 per RPM metre connect karna hai video

[@akleshkumar2562]

Sir piliss... furbensi bus beten se solo & fast

[@j.s.electricalinstrumentat2146]

Please explain your problem again

[@goodwinrenato9301]

how to set 2 m0tors on one ATV 320 vfd

[@j.s.electricalinstrumentat2146]

Output of VFD connect at 2 number of MCB's & motors connect on these MCB'se

[@usmanahmed9929]

Slow and fast speed mein reverse and Forward kaise chalate h
please reply sir

[@manidhaliwal8017]

Sir ji soda Numbr mil sakda ji plz