Mine will be 20 years old next year, I replaced the original jincheng engine with a Lifan, that did 14000 miles I only changed oil 3/4 times I wanted to kill it,,, could not bearings worn vibration crazy, but it still ran, put new spare engine in it, and replaced front and rear forks, but done well, bought in 2008 in UK for £375
I've got 2 of these bikes, one is a 125 symoto almost new, the other is a zhenhua11 years old, been well used and its better made. The chrome is not bad and there's no rust like on yours. I agree about the fixings must be checked, plus the cables should be oiled and bolts like wheel spindles and swinging arm should be greased. Your chain has stretched because you haven't oiled it. I can see the brown rust on it. The foot peg is bent, probably were your son has hit it, that would explain the missing rubber. There great bikes and very cheap to replace parts. 👍😎
I was riding the real Honda 70s back when they were new and loved them. Sounds like for just basic riding around this would be okay as long as you go over the whole bike and Loctite everything like you said to make sure nothing falls off, lol. I was looking for a used genuine Honda 70 but the prices are high for one in nice condition. Thanks for the video.
I would do a monthly inspection checking bolts, linkage of the brakes, headlights running lights blinkers. And oil the chain. An oiled chain will last a whole lot longer than one that isn't oiled. I don't think he ever oiled at chain. When replacing nuts if possible use lock nuts. Lastly change the oil early on to full synthetic. Do all this and I'm guessing you will see many years of enjoyment out of your bike. If all he said was true and it's made this cheaply at some point be prepared for wheel bearing failure. If you don't do this on your own it still shouldn't cost to much to repair. One more thing all he wound have to do for that loose chain is loosen the tighteners remove the master link and with a chain breaker remove one link. Keeping the chain oiled will greatly extend the life of the sprockets too. Keeping the chain oiled is a must no matter what make it is. I owned a Honda 70 Tail Bike about 1970 it would do about 50 mph with the wind at your back. It was a lot of fun to drive on or off trail.
I got one, Chuck the carb, handle bars and exhaust. tighten everything. trail buddy for parts and advice for moving the front fender and fixing the swingarm. Buy a Honda if you don't like fixing your ride. once dialed in I love mine.
I have put 700 hard off-road miles on mine and it runs great, just keep changing that oil. It does take a lot of maintenance because it's made out of China metal so things break and bend. Also, the stock exhaust and carb really choke her up.
I started riding motorcycles on a ct 70 it was a 4 speed with a clutch I also had one that had the 3 speed auto clutch what do these bikes have? I was looking at these just to get around the area on not really long trips. I'm not afraid working on then but it's good you pointed out what gets loose easily.
i plan on buying one and completely changing it.. i have a 190 zongsheng 5spd motor. having a hard time debating on getting a clone or the real thing...
Thinking about getting one. Had 72 CT- 70 I have a Chinese Raven 250 great bike. I use chain lube or general-purpose grease. No chain Issues. Where is the best place to buy one Amazone does not carry them. THANK YOU, RICK
Stock front fender had to drill holes to raise it and add spacers then trim off the back about an inch to clear the engine (could have mounted more forward but did not like the look) and of course cut off the mounts on the side. From forks are fine in fact a lot soft. I would change the fluid apparently there is no quality control on adding the correct amount.of fluid
Tell me where do you order upgrades to tires and shocks?? From dealer we get them from.. any 3rd party parts.. please provide where to get parts and if you have a master list of all upgrades please send to me... i just ordered a champion last night.. thx cliff
Wow! Looks are deceiving! After hearing the laundry list of stuff that honestly needed to be replaced or modifie, I would go for something that's not as cool to look at but is put together better. That's just me. I don't have the time, patience, or place to make all those changes to get the bike where it needs to be. I'm surprised Honda or another manufacturer hasn't produced a retro style mini-bike like the CT 70 in the past few years. There are a few, but they lack the retro styling us late boomers love.
Honda did come out with a new Dax 125 it’s the same engine as the Grom, Monkey, Trail 125. They just haven’t brought it to the states. It’s available in the UK though.
I think the footpegs are on a bolted on bar so they could be replaced. Yeah, the bike needs loctite and some TLC. Honda didnt offer the DAX here in the U.S. and the price would be double of this.
Where'd you get the Honda stickers? China gonna china... wonder if worth it to just buy the real thing. Considering resale at the end, Seems like its "cheap" as in crap not as in a good value. Dax coming here next year maybe?
Mine will be 20 years old next year, I replaced the original jincheng engine with a Lifan, that did 14000 miles I only changed oil 3/4 times I wanted to kill it,,, could not bearings worn vibration crazy, but it still ran, put new spare engine in it, and replaced front and rear forks, but done well, bought in 2008 in UK for £375
I've got 2 of these bikes, one is a 125 symoto almost new, the other is a zhenhua11 years old, been well used and its better made. The chrome is not bad and there's no rust like on yours. I agree about the fixings must be checked, plus the cables should be oiled and bolts like wheel spindles and swinging arm should be greased. Your chain has stretched because you haven't oiled it. I can see the brown rust on it. The foot peg is bent, probably were your son has hit it, that would explain the missing rubber. There great bikes and very cheap to replace parts. 👍😎
I was riding the real Honda 70s back when they were new and loved them. Sounds like for just basic riding around this would be okay as long as you go over the whole bike and Loctite everything like you said to make sure nothing falls off, lol. I was looking for a used genuine Honda 70 but the prices are high for one in nice condition. Thanks for the video.
Totally getting one just to mess around with. Get a new chain. Locktite everything down. Good to go.
Agreed
Been thinking of getting one just because they are cheap but it’s good to know what I’ll need to look at before I do get one. Good video!
I would do a monthly inspection checking bolts, linkage of the brakes, headlights running lights blinkers. And oil the chain. An oiled chain will last a whole lot longer than one that isn't oiled. I don't think he ever oiled at chain. When replacing nuts if possible use lock nuts. Lastly change the oil early on to full synthetic. Do all this and I'm guessing you will see many years of enjoyment out of your bike. If all he said was true and it's made this cheaply at some point be prepared for wheel bearing failure. If you don't do this on your own it still shouldn't cost to much to repair. One more thing all he wound have to do for that loose chain is loosen the tighteners remove the master link and with a chain breaker remove one link. Keeping the chain oiled will greatly extend the life of the sprockets too. Keeping the chain oiled is a must no matter what make it is. I owned a Honda 70 Tail Bike about 1970 it would do about 50 mph with the wind at your back. It was a lot of fun to drive on or off trail.
I have a 2018 model no issues no rust but I don’t leave it out in the rain either
I got one, Chuck the carb, handle bars and exhaust. tighten everything. trail buddy for parts and advice for moving the front fender and fixing the swingarm. Buy a Honda if you don't like fixing your ride. once dialed in I love mine.
My ocd is flaring up on that rusty chain dude.
Omg😅😅
I have put 700 hard off-road miles on mine and it runs great, just keep changing that oil. It does take a lot of maintenance because it's made out of China metal so things break and bend. Also, the stock exhaust and carb really choke her up.
I started riding motorcycles on a ct 70 it was a 4 speed with a clutch I also had one that had the 3 speed auto clutch what do these bikes have? I was looking at these just to get around the area on not really long trips. I'm not afraid working on then but it's good you pointed out what gets loose easily.
Subscribed to get you closer to 1000!
It would be cool to swap a CRF110 onto it. And change that swingarm out for a real ct70 swngarm. I’ve been tempted to buy one for a while now
i plan on buying one and completely changing it.. i have a 190 zongsheng 5spd motor. having a hard time debating on getting a clone or the real thing...
Thinking about getting one. Had 72 CT- 70 I have a Chinese Raven 250 great bike. I use chain lube or general-purpose grease.
No chain Issues. Where is the best place to buy one Amazone does not carry them. THANK YOU, RICK
I believe Cajun maddogs. Is the go to company for these.
Subbed !! What front fender is that ? Did you do anything to the front forks ? Mine are like rocks and don't move / compress very easy !
Stock front fender had to drill holes to raise it and add spacers then trim off the back about an inch to clear the engine (could have mounted more forward but did not like the look) and of course cut off the mounts on the side. From forks are fine in fact a lot soft. I would change the fluid apparently there is no quality control on adding the correct amount.of fluid
Drain your forks and put light weight fork oil in them
Tell me where do you order upgrades to tires and shocks?? From dealer we get them from.. any 3rd party parts.. please provide where to get parts and if you have a master list of all upgrades please send to me... i just ordered a champion last night.. thx cliff
man that chain needs to be oiled so bad
You're wrong. I've put over 2500 miles on my clone, and have had few problems. Also haven't had the bolts vibrate like yours.
Are you able to switch the bars out?
Rubber on foot peg just fell off? Why does it look bent?
Made in CHYYYNA
Wow! Looks are deceiving! After hearing the laundry list of stuff that honestly needed to be replaced or modifie, I would go for something that's not as cool to look at but is put together better. That's just me. I don't have the time, patience, or place to make all those changes to get the bike where it needs to be. I'm surprised Honda or another manufacturer hasn't produced a retro style mini-bike like the CT 70 in the past few years. There are a few, but they lack the retro styling us late boomers love.
Honda did come out with a new Dax 125 it’s the same engine as the Grom, Monkey, Trail 125. They just haven’t brought it to the states. It’s available in the UK though.
Awww man! That DAX 125 is exactly what I'm talking about!! @@GratefulEd907
@@Hodenkat yep I want one it’s the coolest mini moto Honda has out and we can’t get it
So what I am hearing is Blue loctite all the bolts and nuts.
That is the best recommendation I can give. Especially the bolts that hold in the starter
I think the footpegs are on a bolted on bar so they could be replaced. Yeah, the bike needs loctite and some TLC. Honda didnt offer the DAX here in the U.S. and the price would be double of this.
what tire size is on that? They look great
I got 400x10 on mine, there great
What if I want to buy that tshirt??
They have a invention called chain lube, just saying
Where'd you get the Honda stickers? China gonna china... wonder if worth it to just buy the real thing. Considering resale at the end, Seems like its "cheap" as in crap not as in a good value. Dax coming here next year maybe?
They look nice but are cheaply made from china. Honestly not worth 1500
I have one of these. It's a p.o.s. Has 500 miles on it.
Chain lube
Is this a real Honda ?
Icebear
NO. Read description
Get that Honda decal off that Chinese crap
Made in China 😂