Can You Jump A Tool Battery to Revive It? | Milwaukee M12 Battery Jump

Поділитися
Вставка
  • Опубліковано 6 жов 2024
  • Amazon Affiliate Link(s):
    Multimeter: amzn.to/3JL2deI
    Alligator Clips: amzn.to/3z3nDyz
    Electrical Connectors: amzn.to/3TGTCOA
    Electrical Tape: amzn.to/40grrZg
    Follow me: / learn.save.diy
    Disclaimer:
    I am not an expert, just an average Joe who enjoys DIY'ing. Learn, Save, DIY assumes no liability for property damage or injury incurred as a result of any of the info from this video. Use this information at your own risk. Due to factors beyond the control of Learn, Save, DIY, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Learn, Save, DIY.

КОМЕНТАРІ • 44

  • @ironman1518.
    @ironman1518. Рік тому +6

    Thak you it IS worth a try at the prices of Milwaukee m-12 batteries. Thank YOU!! It did save my M-12 3ah battery!!

  • @panzon
    @panzon Рік тому +6

    Great.. i just save my M12 6Ah Battery. Tnx

  • @resptodd1
    @resptodd1 6 місяців тому

    Used it on my m18s... Worked like a charm.!! Thank you.!!

  • @tirefrier8253
    @tirefrier8253 4 місяці тому +5

    Dude. After you boost the bad battery. No batteries in the charger. Unplug the charger for 1 minute. Put the bad battery in the charger and plug in the charger. Voila !!!!

    • @learnsavediy
      @learnsavediy  4 місяці тому +3

      I'll have to give it a shot. I'm not sure why that would work but if it does, I'm all for free fixes!

    • @kz0197
      @kz0197 11 днів тому

      after boost , my m12 battery still couldn't charge , but trick with unplugging charger worked for me, thanks for sharing.

  • @ricvoils781
    @ricvoils781 Рік тому +3

    The process worked like a charm for a Redlithium USB 3.0 battery off two D cell batteries, thanks for sharing

  • @scottfirman
    @scottfirman 9 місяців тому

    I did this on my daughters battery, but it was the bigger one. I tested each cell and discovered one totally bad cell. A cell that is flat will never come back. Good try . I give you credit. I generally find the same thing happens. The battery charges to a certain level, after another attempt, it actually loses voltage. At that point, it's a candidate for the recycle bin.

  • @geoffhubbard7815
    @geoffhubbard7815 Місяць тому

    (Flashing error) make sure to check the temp sensor tab (rightmost P tab on the side, I believe) if one is lower or dented, use a pick to bend it back straight.... sometimes it isn't the cells; it can just be a bad connection on that P terminal causing the device as well as the charger to think it is overheating.

  • @michaelbaker4770
    @michaelbaker4770 9 днів тому

    Could you try a 12v car battery?

  • @dennisbielov8604
    @dennisbielov8604 5 місяців тому

    I just restored 2 of my m12 6.0 batteries this way. They were drained due to sitting long time (very long time) without use.

  • @ronnwalk9597
    @ronnwalk9597 2 місяці тому

    It worked

  • @jeffjohnson5390
    @jeffjohnson5390 4 місяці тому

    I had two m18 batteries that I jumped this way and brought them both back to life.

  • @jayyy.moneyyy
    @jayyy.moneyyy 4 місяці тому

    Worked on mine. Jumped a battery just like yours in the video with the same battery. I tried it a while back with 20v dewalt batteries, but it didn’t work

    • @learnsavediy
      @learnsavediy  4 місяці тому

      Bummer, at least you got one back!

  • @rrboss33
    @rrboss33 4 місяці тому

    Works on m18 too

  • @chloeleedow7250
    @chloeleedow7250 10 місяців тому +1

    I'd trickle charge it using a car charger for couple of hours 2 amp or something outside. Just for shits and giggles, I wouldn't be defeated that easily bud. 😊

  • @kat-yv5sm
    @kat-yv5sm 6 місяців тому

    Also if you keep just taking it off and back on the charger it will eventually charge up enough to take charge again. Ask me how I know

    • @learnsavediy
      @learnsavediy  6 місяців тому

      I’m all for free and easy fixes!

    • @crazyedd707
      @crazyedd707 6 місяців тому

      How long did it take u?

  • @bombing626
    @bombing626 10 місяців тому +1

    I’m pretty sure you’re supposed to leave it jumped for way longer than a minute

    • @learnsavediy
      @learnsavediy  10 місяців тому +2

      @4:20 I mention I let it sit for up to 30 minutes and still no change. I’ve done this many other times with other batteries and if the cells are good it does in fact takes less than 1 minute to jump the battery.

    • @ronnwalk9597
      @ronnwalk9597 2 місяці тому

      I did it for one minute and slapped it on charger right after and it worked. I didn't want to leave it for a long time and risk hurting my newer battery. I've done this before and it not work but I just wanted to try it again rather than throw another battery in trash. It worked and saved my battery. Appreciate the video and the save of 80 bucks

  • @michaelgoodwin5162
    @michaelgoodwin5162 Рік тому

    A better-quality charger COULD help. I had this scenario with a 12v DeWalt.

    • @learnsavediy
      @learnsavediy  Рік тому +2

      I'm not following. How is an OEM battery charger not quality? Or are you just saying in general a generic charger is not as good as a OEM one?

    • @michaelgoodwin5162
      @michaelgoodwin5162 Рік тому

      The more expensive and or rapid chargers often have better electronics. Some of the guys I buy tools from can't give those M12 chargers away. I have a couple I've never used.
      So the experience I had with DeWalt was a 12 volt 1.5 AH battery that came in a kit. The cheap kit charger would not charge it due to heat. I tried it in DeWalt's 4 bay fan cooled rapid charger. No problem.

  • @JayTee-fp7ig
    @JayTee-fp7ig 11 місяців тому +2

    Not worth the risk with the 12volts, buy a knock off waitly for $10 they work almost perfectly out of 12 I had one bad. Fuck Milwaukee and their $200I batteries that last 4 years with 15 charges only on them.
    I done this hack with big paper clips for the M18s and I had luck both times BUT the paper clips got instantly HOT in 3-4 seconds. I could see a fire coming if I waited any longer , I immediately disconnected them burning my fingers. But fixed both my m18s. You put fire and burn on the line. Wear gloves,do it outside and use 14 gauge Rolex wires with goggles if your a gambler. If no luck but the knock offs m18 never had a problem with them. For every 4 year old Milwaukee that bad with 15 charges on them I don’t reward Milwaukee I reward their competitors

  • @renec0327
    @renec0327 24 дні тому

    Fukkk I almost explode my self, with my 12 v milwaukee 4.0 😅

    • @learnsavediy
      @learnsavediy  22 дні тому

      What specifically happened? That’s why this video was educational, not a how to.

  • @neeko7878
    @neeko7878 Рік тому +1

    The only thing about jumping the battery is you need to do it every time pretty much

    • @learnsavediy
      @learnsavediy  Рік тому +3

      It depends. It’s just about getting it above that nominal voltage so the charger recognizes it. If the cells are good, just discharged, you should only need to do it once unless you let it keep dying. If the cells are bad, then yes. I’ve done this to other batteries that just were sitting for years and now charge on their own in the charger after only jumping it once.

    • @3vlogs487
      @3vlogs487 Рік тому

      Or in our case we left it sit dead for a month

  • @synthaxterrornotmr.z569
    @synthaxterrornotmr.z569 Рік тому +2

    Well.. Your basically more right than wrong in thinking something like this might be possible.... By correctly assuming that one unchargable battery could be "jump started" or brought back to life by connecting it in paralellwith a fully charged battery...But you have to account for the fact that each battery is a package of several battery cells... which is 3 in this case.... If you apply your method at that level it will most likely put enough charge into the "drained" battery cell so that a regular charger could finish the job as usual.....Also the voltage in each battery cell must be in equalibrium aka balanced....If you do that , put it back into the original pack it should all be fine and dandy...More or less!..;-)

    • @UtahTrucksToolsBikeGuy
      @UtahTrucksToolsBikeGuy 9 місяців тому +4

      Dude why are you telling him the same thing he went over in the vodeo. Hes explaining this as a tutorial it dont need your blah blah dont have a college degree blah blah nonsense with an overcomplicated explanation of rubbish. I dont think theres one fact in your entire comment

  • @troyc5994
    @troyc5994 2 місяці тому

    You had the battery jumped in reverse polarity in your video! You are lucky the battery did not blow up on you. Check your work again.

    • @learnsavediy
      @learnsavediy  2 місяці тому

      Rewatch @1:07 and @2:57. The negatives are at the left/top while the positives are on the right/bottom. It is wired correctly.