Automatic activation according to temperature is not possible for legal reasons, as the vehicle could also be parked in a garage, where operation is prohibited. However, you can set a "departure time" with the EasyStart Web, then the heating will start in time depending on the outside temperature.
@@eberspaechercom " as the vehicle could also be parked in a garage, where operation is prohibited." What a completely bogus reason. The vehicle could be parked in a garage with the timer set too! There's zero difference for a thermostat mode, you just want to charge people two hundred bucks for a useless hunk of plastic.
Would it be possible to point me to an installation of the EasyStart Pro? I am trying to determine if there is a more robust manner in which to install the controller to a flat surface vs. using sticky back tape or velcro (hook& loop). Thank you.
Hi! Our UK colleagues posted a video about two years back. At around 4:15min, you can see how what they did with the control unit. I hope that's what you were looking for? :) ua-cam.com/video/OZGDe7WJf94/v-deo.html
My new camper van has the heater and easy pro installed under the passenger seat. In order to use the easy pro I must get down on my hands and knees. Can the easy pro control unit be moved and installed elsewhere in the campervan?
@@eberspaechercom Another question. Is there a way to make it default to no time limit and to make it default to a particular temperature? I’ve tried setting it over and over but it keeps going back to 30 minutes when I started back up
There is no installation video, as only trained professionals are allowed to install our products. However, a first-start video is a good idea we are working on. Thank you!
Hey Eberspächer, I've just got 2x S2 D2's installed today professionally. However, I haven't been shown how to use it. Any word on this first start video?
Hi Jelle, can you send us a photo with the heater and type label? Even if you can use the EasyStart Pro for this, it probably makes little sense because most of the functions would not be available. But first of all, a picture would be helpful.
Thanks for your question. The EasyStart Pro can be connected either via CAN or the plus terminal on the ignition coil. Which heater are you controlling with your EasyStart Select?
I have the S2D2L with Easy Start Pro controller and can't figure out how to adjust the target temperature WHILE the heater is operating...other than to stop the heater and re-start to change temp and/or run time duration. Is there a method to adjust the heater's target temperature and run time WHILE the heater is running? Thanks in advance!
Hi Dan, thanks for your question. This is indeed possible, but only in a somehwat roundabout way. Basically, if you select to change the operating time while the heater is running, you should come across a menu screen where you can also adjust the temperature. Let us know if that works with your make and modell.
We are happy that you are interested in our products. Our new EasyStart Pro is a CAN-based control unit. The Hydronic M2 (8-12 kilowatt) heater is based on LIN communication. Due to that, this heater is not compatible with our EasyStart Pro. Alternatively our EasyStart Select and EasyStart Timer can be used with the Hydronic M2.
Hi Nicole, thanks for your question. Usually, the display language is set up during installation. We are afraid you have to consult with your workshop, because language settings are only accessible with the correct diagnostic tool. Hope this helps!
@@eberspaechercom I installed this unit and sped through the setup knowing that it was only a temporary battery connection and not knowing the language would forever be set… can I NOT change the language through the settings?
@@NicolePietri Have you checked the manual? You can download it here: www.eberspaecher.com/fileadmin/data/corporatesite/pdf/technische_doku/EasyStart_Pro/Bedienungsanweisung/22.1000.35.2204.0A_EN_0721.pdf Should that come up short, either consult with your workshop or contact our technical support - you'll find their info on the last page of the manual.
This controller seems easy when you watch a video, I'm still trying to figure it out. Can I set it up so it will start and stop let's say every two hours? You showed it can be set for instance to 7am and run for several minutes, can I for instance set 7am 9am and 11am for it to run for 30min same day for few days on n on?
Hi Paul, thanks for your question. With the EasyStartPro, you can program multiple "events" per day, even for the same day - in your case for 7am, 9am and 11am. But be aware that for safety reasons, you can only set timers for seven days in total, after which you would need to re-activate the events. If you need any pointers, you can download the manual here: www.eberspaecher.com/en/download-center/operating-instructions/current-models. Hope that helps! :)
@@eberspaechercom thank you very much for your reply! I figured it our, spent some time circling around was worth it, based on your video. It's super easy, but there is something that I still don't know. You mentioned at the end of the video there is an app, can this be managed remotely? As far as I understand controller would have to be connected via some network same as GPS in order for it to navigate through a phone.
Hi Paul! In this case, you would need to install an additional EasyStart Web. The ESW can be linked to the EasyStart Pro with a special cable. Then, you can connect to the app via internet. But as mentioned, you'd need an EasyStart Web.
@@eberspaechercom thanks again for your reply. That would be a slam dunk for me. So an ESW is a device? How do I get it? I'm assuming you have them on your website. If you could get me a direct link to it that be great 👍 👌
Hi Paul, sure thing. You can find out more about the ESW here: www.eberspaecher-climate.com/products/accessories/remote-controls If you like what you read, you can search for local dealers here: www.eberspaecher-dealer-locator.com/
Hello, can I use EasStartPro to control the Hydronic S3 (as main heater in my RV) based on indoor temperature? I need the heater keep the interior temperature constant (or in some range). thanks for information
Is the high altitude function automatic as it is with Eberspacher High Altitude Kit 22.1000.33.2200 H-Kit or do you manually have to turn it on? I would like to use this with the Eberspacher Hydronic S3 D5E CS 12V
Hi Kyle, In conjunction with the Easy Start Pro control element, the high altitude function can be switched on manually. No additional height kit is required for the Eberspächer Hydronic S3 D5E (article number 25.2934.05 00 00 ) CS 12V.
Hoping you guys can answer this for me. I have installed a S2 Eberspacher with a Easy Start Pro control unit. I have not installed an External Temp sensor wishing to use the one in the control unit. However when I turn on the heater I get no Temperature displayed on the control panel. I have gone into the installation section and selected controller for sensor and display (I think correctly) but no joy. Do I need to adjust the wiring going into the controller when not connecting an external sensor? At present I have just connected the square 4 way plug and left the 3 way connector alone. (which I understand is for the remote sensor.)
Many thanks for your question. We would like to help you here, so please send us an email with your request to the following address: GLOBAL-SocialMedia@eberspaecher.com
@@davec653 Hi David. Good and Bad news. Yes I did get it sorted but can not recall what was required. I dont think it involved any changes to the wiring. If I can remember it was something like removing both fuses then inserting the one powering the controller first and then waiting 30 secs before powering the heater. Then entering setup mode which was something like selecting the wheel type icon then pushing in the main button for 5 seconds. then you can scrool through the background set up instructions. this lets you select controler for display and sensor etc.. You can try this out or if you can find a write sounding like this follow that. Good luck and sorry I cant be more presise.
Maybe this video from our colleagues in North America will help, but we can't guarantee a successful adaptation to your case: ua-cam.com/video/SbcOf4eAm9Y/v-deo.html
Hoping you guys can answer this for me. I have installed a S2 Eberspacher with a Easy Start Pro control unit. I have not installed an External Temp sensor wishing to use the one in the control unit. However when I turn on the heater I get no Temperature displayed on the control panel. I have gone into the installation section and selected controller for sensor and display (I think correctly) but no joy. Do I need to adjust the wiring going into the controller when not connecting an external sensor? At present I have just connected the square 4 way plug and left the 3 way connector alone. (which I understand is for the remote sensor.)
I have this, I cannot figure any way to control based on temperature. I want it to come on when it gets cold basically.
It works that way, what heater do you have?
Automatic activation according to temperature is not possible for legal reasons, as the vehicle could also be parked in a garage, where operation is prohibited. However, you can set a "departure time" with the EasyStart Web, then the heating will start in time depending on the outside temperature.
@@eberspaechercom then your product is useless. You advertise a temperature sensor but all it is used for is DISPLAY?
You absolute con men.
@@eberspaechercom " as the vehicle could also be parked in a garage, where operation is prohibited." What a completely bogus reason. The vehicle could be parked in a garage with the timer set too! There's zero difference for a thermostat mode, you just want to charge people two hundred bucks for a useless hunk of plastic.
@@scottbeale1825 and Richard, see if this link helps you
ua-cam.com/video/dyvgIFP-zqA/v-deo.html
How do I set a TARGET TEMPERATURE?? Just turning the thing on for 30 minutes is useless if the temperature changes from day to day.
Is it possible to use the Eberspächer EasyStart Remote+ and EasyStart Pro together? (Airtronic L3 D6L)
Would it be possible to point me to an installation of the EasyStart Pro? I am trying to determine if there is a more robust manner in which to install the controller to a flat surface vs. using sticky back tape or velcro (hook& loop). Thank you.
Hi! Our UK colleagues posted a video about two years back. At around 4:15min, you can see how what they did with the control unit. I hope that's what you were looking for? :)
ua-cam.com/video/OZGDe7WJf94/v-deo.html
My new camper van has the heater and easy pro installed under the passenger seat. In order to use the easy pro I must get down on my hands and knees. Can the easy pro control unit be moved and installed elsewhere in the campervan?
Of course, the control unit can be moved to wherever wiring is possible.
@@eberspaechercom Another question. Is there a way to make it default to no time limit and to make it default to a particular temperature? I’ve tried setting it over and over but it keeps going back to 30 minutes when I started back up
does it need priming again if its run out of fuel? trying to find a tutorial for priming these heaters but i cant find one anywhere!
It could take 2 or 3 firing attempts based on length of fuel line
As expensive as this unit was, you'd think they would make an installation video, and even a first start procedure video. This is a pain in the ass.
There is no installation video, as only trained professionals are allowed to install our products. However, a first-start video is a good idea we are working on. Thank you!
My buddy had to become a trained professional, took us 3 days to setup due to parts missing in the kit, that were supposed to be included.
Hey Eberspächer,
I've just got 2x S2 D2's installed today professionally.
However, I haven't been shown how to use it.
Any word on this first start video?
can I replace my ebensprächer controlebit 801 by the easy start pro? How is the wiring is case of easy start pro done?
Hi Jelle, can you send us a photo with the heater and type label?
Even if you can use the EasyStart Pro for this, it probably makes little sense because most of the functions would not be available. But first of all, a picture would be helpful.
Can this unit replace a easystart select unit? Or would I need to run new wires?
Thanks for your question. The EasyStart Pro can be connected either via CAN or the plus terminal on the ignition coil. Which heater are you controlling with your EasyStart Select?
Do you have a controller unit for the DH15 Hydronic? Will this allow you to heat water for a shower and also for a fan heater?
Can i use this with my eber waterheater m10 first edition? How to i hook it up?
I have the S2D2L with Easy Start Pro controller and can't figure out how to adjust the target temperature WHILE the heater is operating...other than to stop the heater and re-start to change temp and/or run time duration. Is there a method to adjust the heater's target temperature and run time WHILE the heater is running? Thanks in advance!
Hi Dan, thanks for your question. This is indeed possible, but only in a somehwat roundabout way. Basically, if you select to change the operating time while the heater is running, you should come across a menu screen where you can also adjust the temperature. Let us know if that works with your make and modell.
will this work with a hydronic10 24 volt?
We are happy that you are interested in our products. Our new EasyStart Pro is a CAN-based control unit. The Hydronic M2 (8-12 kilowatt) heater is based on LIN communication. Due to that, this heater is not compatible with our EasyStart Pro. Alternatively our EasyStart Select and EasyStart Timer can be used with the Hydronic M2.
How do I change the language on the control? Im stuck in a foreign language and have no idea how to operate!
Hi Nicole, thanks for your question. Usually, the display language is set up during installation. We are afraid you have to consult with your workshop, because language settings are only accessible with the correct diagnostic tool. Hope this helps!
@@eberspaechercom I installed this unit and sped through the setup knowing that it was only a temporary battery connection and not knowing the language would forever be set… can I NOT change the language through the settings?
@@NicolePietri Have you checked the manual? You can download it here:
www.eberspaecher.com/fileadmin/data/corporatesite/pdf/technische_doku/EasyStart_Pro/Bedienungsanweisung/22.1000.35.2204.0A_EN_0721.pdf
Should that come up short, either consult with your workshop or contact our technical support - you'll find their info on the last page of the manual.
This controller seems easy when you watch a video, I'm still trying to figure it out. Can I set it up so it will start and stop let's say every two hours? You showed it can be set for instance to 7am and run for several minutes, can I for instance set 7am 9am and 11am for it to run for 30min same day for few days on n on?
Hi Paul, thanks for your question. With the EasyStartPro, you can program multiple "events" per day, even for the same day - in your case for 7am, 9am and 11am. But be aware that for safety reasons, you can only set timers for seven days in total, after which you would need to re-activate the events. If you need any pointers, you can download the manual here:
www.eberspaecher.com/en/download-center/operating-instructions/current-models.
Hope that helps! :)
@@eberspaechercom thank you very much for your reply! I figured it our, spent some time circling around was worth it, based on your video. It's super easy, but there is something that I still don't know. You mentioned at the end of the video there is an app, can this be managed remotely? As far as I understand controller would have to be connected via some network same as GPS in order for it to navigate through a phone.
Hi Paul! In this case, you would need to install an additional EasyStart Web. The ESW can be linked to the EasyStart Pro with a special cable. Then, you can connect to the app via internet. But as mentioned, you'd need an EasyStart Web.
@@eberspaechercom thanks again for your reply. That would be a slam dunk for me. So an ESW is a device? How do I get it? I'm assuming you have them on your website. If you could get me a direct link to it that be great 👍 👌
Hi Paul, sure thing. You can find out more about the ESW here:
www.eberspaecher-climate.com/products/accessories/remote-controls
If you like what you read, you can search for local dealers here:
www.eberspaecher-dealer-locator.com/
Hello, can I use EasStartPro to control the Hydronic S3 (as main heater in my RV) based on indoor temperature? I need the heater keep the interior temperature constant (or in some range). thanks for information
Yes you can! DO you have a Easystart Pro Manual?
Yes, the EasyStart Pro is compatible with the Hydronic S3 and has an integrated temperature sensor.
Is the high altitude function automatic as it is with Eberspacher High Altitude Kit 22.1000.33.2200 H-Kit or do you manually have to turn it on? I would like to use this with the Eberspacher Hydronic S3 D5E CS 12V
I have the exact same question:)
Hi Kyle, In conjunction with the Easy Start Pro control element, the high altitude function can be switched on manually. No additional height kit is required for the Eberspächer Hydronic S3 D5E (article number 25.2934.05 00 00 ) CS 12V.
Hoping you guys can answer this for me. I have installed a S2 Eberspacher with a Easy Start Pro control unit. I have not installed an External Temp sensor wishing to use the one in the control unit. However when I turn on the heater I get no Temperature displayed on the control panel. I have gone into the installation section and selected controller for sensor and display (I think correctly) but no joy. Do I need to adjust the wiring going into the controller when not connecting an external sensor? At present I have just connected the square 4 way plug and left the 3 way connector alone. (which I understand is for the remote sensor.)
Many thanks for your question. We would like to help you here, so please send us an email with your request to the following address:
GLOBAL-SocialMedia@eberspaecher.com
@@eberspaechercom Thank You
What heater are you using?
hi tony , i have this prob to did you get it sorted
@@davec653 Hi David. Good and Bad news. Yes I did get it sorted but can not recall what was required. I dont think it involved any changes to the wiring. If I can remember it was something like removing both fuses then inserting the one powering the controller first and then waiting 30 secs before powering the heater. Then entering setup mode which was something like selecting the wheel type icon then pushing in the main button for 5 seconds. then you can scrool through the background set up instructions. this lets you select controler for display and sensor etc.. You can try this out or if you can find a write sounding like this follow that. Good luck and sorry I cant be more presise.
Molto spesso il riscaldatore mi da errore H1 da cosa può dipendere ?
A volte è capitato che si resetta da solo non riesco a capire da cosa dipende.
Maybe this video from our colleagues in North America will help, but we can't guarantee a successful adaptation to your case: ua-cam.com/video/SbcOf4eAm9Y/v-deo.html
J'aimerais cette explication en Français SVP.... merci
Moi aussi comment il faut faire ?
All videos available in French can be found at our French channel: ua-cam.com/channels/cOvnilZDpdCdjjxoY6LJew.html
Can I use this with my d5wz
It is possible but not easy. The best thing is to ask the Eberspächer dealer you trust. Thank you!
@@eberspaechercom thank you..
Mi piacerrbbe che fosse tradotto in italiano grazie
Hi Roberto, take a look at the channel from Eberspächer Italy: ua-cam.com/channels/-u_xilF4ifArhHhY6cSYDQ.html
En français
All videos available in French can be found at our French channel: ua-cam.com/channels/cOvnilZDpdCdjjxoY6LJew.html
controlebit....: I mean control unit!
По нашему случайно нету?
Can you please specify in English? Thanks!
This is near useless. It summarises the functionality but doesn't teach how to use it!!!!
Hoping you guys can answer this for me. I have installed a S2 Eberspacher with a Easy Start Pro control unit. I have not installed an External Temp sensor wishing to use the one in the control unit. However when I turn on the heater I get no Temperature displayed on the control panel. I have gone into the installation section and selected controller for sensor and display (I think correctly) but no joy. Do I need to adjust the wiring going into the controller when not connecting an external sensor? At present I have just connected the square 4 way plug and left the 3 way connector alone. (which I understand is for the remote sensor.)
Unfortunately, we cannot answer this technically demanding question here. It is best to contact your trusted Eberspächer dealer directly. Thanks!