Nice drill. I'd love to play with that for just one week. Hilti is pricey but they sure make some quality equipment. I think a lot of the time the guys that bitch about the cost of their products are really just jealous maybe. I'm one of them I can honestly say. I can still remember the first time I used a 480v drill. It was the pentruder model. I drilled an 8" dia. 12" deep.....45 seconds. I thought I was dreaming. Nice job man.
I know this the DD500 but have you heard that a DD350 was used to break into a vault in London? Media is currently estimating the theft could be as much as £200 million but they aren't sure yet, as it was a 'safe' deposit. Yours is the most detailed video I've found that could be used as a DIY guide....wonder if they used your video?? The wall was 2m thick....can you get extensions for these? Or do you think they had to make their own?
Yes, you can core drill almost any depth, all manufacturers sell extensions, sometimes long barrel core bits are made up or ordered for thick drilling.
RA30st08 The HILTI could do it, through concrete, same bit more extension. But apparently the 'heist' was 2m through reinforced concrete rebar, and you'd have to be 4yo small to get through a 350mm, 2m long tunnel. Imagine a 30cm ruler held out infront of you.
I think they must have drilled a series of holes to create an opening, i'm guessing at least 600 mm in diameter. that would require around 19 holes at 100 mm, looking at 45 per hole.
I noticed all tools have close resemblances the color and name brand are the two differences, the wanker using the tool is what really matters. SAFETY FIRST MATES👷 cheerio
Elizabete geraldina silva Meu nome é Elizabete trabalho com Desentupimento e Hidráulica na Empresa SDB e quero saber se ela trabalha também caixas visita na hidráulica? quanto custa e forma de pagamento,se é a diesel,e quanto tempo trabalha por litro e posso trabalhar onde existem pontos com pedras.
Hi, This generator was a John Deere mounted inside a a 5 tonne truck. I do not recall who built it for us. If you are looking for something to run a 480 Volt core drill I would suggest looking at MAKINEX 16 kw 480 Volt generator. Hope that helps
Bertie Blue You have to drill to the full depth of the barrel and then use a wedge to snap the core and pull it out.Add an extension to the bit and drill again, repeat until through the wall.
Nice drill. I'd love to play with that for just one week. Hilti is pricey but they sure make some quality equipment. I think a lot of the time the guys that bitch about the cost of their products are really just jealous maybe. I'm one of them I can honestly say. I can still remember the first time I used a 480v drill. It was the pentruder model. I drilled an 8" dia. 12" deep.....45 seconds. I thought I was dreaming. Nice job man.
"Some people would kill for an ass like this." lol
Hatton Garden Heist brought me here ;)
Rob, this happens all the time.
the wall is 20 some years old.
we are drilling the holes for equipment upgrades.
Every bank robber in the world is watching this video ;P
I know this the DD500 but have you heard that a DD350 was used to break into a vault in London? Media is currently estimating the theft could be as much as £200 million but they aren't sure yet, as it was a 'safe' deposit.
Yours is the most detailed video I've found that could be used as a DIY guide....wonder if they used your video?? The wall was 2m thick....can you get extensions for these? Or do you think they had to make their own?
Yes, you can core drill almost any depth, all manufacturers sell extensions, sometimes long barrel core bits are made up or ordered for thick drilling.
That's why I'm here I wanted to see how could this drill get through the safe
RA30st08 The HILTI could do it, through concrete, same bit more extension. But apparently the 'heist' was 2m through reinforced concrete rebar, and you'd have to be 4yo small to get through a 350mm, 2m long tunnel. Imagine a 30cm ruler held out infront of you.
I think they must have drilled a series of holes to create an opening, i'm guessing at least 600 mm in diameter. that would require around 19 holes at 100 mm, looking at 45 per hole.
kollenberg74 Wonder if they got a kid or dwarf in on it....just like Bad Santa lol
My god, what a buzz that must have been, crawling out of the hole inside the vault.
This drill must draw quite a bit of power under load. If you tried making a hole in an Italian bank vault you would end up tripping the whole street.
It is Hilti Co. The poor operator should be sitting under an umbrella branded with Hilti logo.
Do they go around in tangerine colored vehicles? They do here in the Philippines
Milwaukee is coming out with an M18 version.
Brilliant, hope they don't get caught.
I noticed all tools have close resemblances the color and name brand are the two differences, the wanker using the tool is what really matters. SAFETY FIRST MATES👷 cheerio
Very good !!
no chance of robbing it now, the owner has installed high tec alarm systems including heat and vibration systems.
Elizabete geraldina silva
Meu nome é Elizabete trabalho com Desentupimento e Hidráulica na Empresa SDB e quero saber se ela trabalha também caixas visita na hidráulica? quanto custa e forma de pagamento,se é a diesel,e quanto tempo trabalha por litro e posso trabalhar onde existem pontos com pedras.
I'm curious if anyone needs a used one of these? I've got one going cheap, only used to drill 3 times. Thx.
How much did you sell it for
3X 20" holes at 16"
Arrival on site 7:30 packed up at 11:30
Nice drill nice setup...but on big holes just use hydraulics.....check out....core drilling a 43
Did the concrete guys forget to lay the formwork for this hole or what?
What generator did you use? Brand and model? Thanks
Hi, This generator was a John Deere mounted inside a a 5 tonne truck. I do not recall who built it for us.
If you are looking for something to run a 480 Volt core drill I would suggest looking at MAKINEX 16 kw 480 Volt generator. Hope that helps
So this is probably the video the robbers used....lol.
***** hmmm i should get a cut
how does the "concrete plug" come out?
Bertie Blue You have to drill to the full depth of the barrel and then use a wedge to snap the core and pull it out.Add an extension to the bit and drill again, repeat until through the wall.
kollenberg74 Thanks mate, do you know anything about safe deposit boxes? haha
This might b a stupid question, but how do you get the material out after?
whyexactly Ha you didn't watch to the end :)..... drill until almost through then snap the core and pull it out.
How much cost this hole ?
We have the core drill bit for HITLI
O na sucho może się zatrzeć, jak mawiała pewna dziewczyna 😜
Wspaniała maszyna.
во во и щас на такой машине еду бетоны просто тема советую
How much per our? Or for hole
Gut
NICE VID!
crack that vault
Арматура была в бетоне????????????
3 year experience Concrete cutting machine operator .I need a job
wtf! what NM torque?
thats great time
this video doesnt tell which bank to target
DD 200?
Came here from imgur like if you did the same
Рабочая лошадка
E La Madonna !!!
на кой там ключ? патрон от руки должен закручиваться!
он ключиком держит чтобы не вращался патрон
Патрон с такой коронкой провернуть тяжело.
Обычно вставляется коронка в патрон, и гайка накручивается от руки.
обычно-это когда коронка обычная, а тут елдень
hilti is the guvnor.hehe
Перфоратор 80 лвл
IT MUST BE 380V NOT 480
No it’s 480 Volt
nice video....check out mine.....core drilling a 43"
Scott L howmuch