WTH??? You do not show how to do the initial manual level? Do I start with all four level knobs tighten down until just close to fully compressed spring? Or just in the random place they were set to out of the box? The first instruction in bed leveling pt. one is "slightly tighten the four bed leveling nuts before initial leveling" which to me means compress the spring until ALMOST completely compressed. But now I do not know and I am looking for a video that goes through EVERY STEP!!! Not start in the middle of the process!!!
Just a quick comment or two. I bought a 10S Pro a year and a half ago as my first 3D printer and then life got in the way and the printer has been in the sealed box ever since. So I'm about to unbox my printer and have started looking for help in setting it up as a complete noobie. So far the first couple of other videos I've seen basically complain that the instructions for setting up the auto leveling are terrible and apparently only someone already knowledgeable about 3D printers will get this printer successfully setup for the auto level to work correctly. In your video you don't seem to think that there was anything to setting up the auto level and you talked as though you were addressing an audience of experienced users. The other thing that I'm finding is that most of the videos for this printer are 1 to 3 years old and so I'm still trying to figure out where more current informational resources exist for this apparently old discontinued model might be.
Hi I have this machine and been having some issues with the extruder clicking,I changed the nozzle the tubing and cleaned it making sure it was not clogged but still the extruder is clicking
in fact, this video isn't a bed leveling video at all. its just like "turn the key on your car and hit the right pedal... and now you know how to drive".
it's not taken over the cr10s, i just upgraded my cr10s to a 32 bit board and a complete conversion with no control box. 700.00 is too much when you can upgrade the cr10s to do the same thing for 125.00 is what i spent.
I have had the CR-10S Pro for about 2 months it is an awesome printer, the only issue I am having is that is difficult to remove the print from the print bed, any ideas would be much appreciated. 👍
I had the same problem. After a cocktail of cleaners, hair spray, acetone, isopropanol, and much more I cant remember It now has trouble keeping pieces on... All I can say is, don't use acetone, since that seemed to do the most damage. Nowadays I clean with Windex after each print.
Does enyone have a problem with the chip reader on this 3D printer? I had the joy only one to print with it but then i couldn't manage to make the chip reader to actually read the SD card ... i tryed a thousand times and it s just annoying... i just recieved it today and i m already having problems with it Can anyone help me, please!!
You sorted this right? Did you swap out the card to your pc to check it could read the card OK? BTW - I've had no end of problems with Win 10 USB / brand new micro SD cards being recognised as computer says 'NO!' 'Write protected'. Format it in your camera - was my solution after trying many other various software utilities and register hacks! Windoze! Don't ya jus luvit? Not!
i watc hed your first vid with the unboxing ect i now have a lovely hole and deep gouge in my bed the 0.20 gauge should be used NOT paper im quite pissed perhaps You should do all the build ect box it back up and not go through it like you know! because you waffled though the vid
this printer uses the capacitive sensor also for home point of Z axis, since this system is not repetitive it will be impossible to calibrate this printer and print in the future without problems, when the next day you print, you will have a different home point , so it will be impossible to print immediatily. Every once you turn on the printer (almost always) you will have to repeat the procedure, which is very frustrating. I have changed mainboard to my cr10s-pro, now every time that I light up I immediately go to press without problems, my first layer is always the same, equal to my first set-up The lords of Creality .... instead of sending free printers to many people, should respond to support requests from customers who have bought their printers, they have never reply my e-mails. A company can also make design mistakes (this is human) but if it does not respond to customers it will be a low-level company
WTH??? You do not show how to do the initial manual level? Do I start with all four level knobs tighten down until just close to fully compressed spring? Or just in the random place they were set to out of the box? The first instruction in bed leveling pt. one is "slightly tighten the four bed leveling nuts before initial leveling" which to me means compress the spring until ALMOST completely compressed. But now I do not know and I am looking for a video that goes through EVERY STEP!!! Not start in the middle of the process!!!
You missed adjusting the senser
Good informations Richard~ Thanks~~~
Just a quick comment or two. I bought a 10S Pro a year and a half ago as my first 3D printer and then life got in the way and the printer has been in the sealed box ever since. So I'm about to unbox my printer and have started looking for help in setting it up as a complete noobie. So far the first couple of other videos I've seen basically complain that the instructions for setting up the auto leveling are terrible and apparently only someone already knowledgeable about 3D printers will get this printer successfully setup for the auto level to work correctly. In your video you don't seem to think that there was anything to setting up the auto level and you talked as though you were addressing an audience of experienced users. The other thing that I'm finding is that most of the videos for this printer are 1 to 3 years old and so I'm still trying to figure out where more current informational resources exist for this apparently old discontinued model might be.
Hi I have this machine and been having some issues with the extruder clicking,I changed the nozzle the tubing and cleaned it making sure it was not clogged but still the extruder is clicking
in fact, this video isn't a bed leveling video at all. its just like "turn the key on your car and hit the right pedal... and now you know how to drive".
it's not taken over the cr10s, i just upgraded my cr10s to a 32 bit board and a complete conversion with no control box. 700.00 is too much when you can upgrade the cr10s to do the same thing for 125.00 is what i spent.
I have had the CR-10S Pro for about 2 months it is an awesome printer, the only issue I am having is that is difficult to remove the print from the print bed, any ideas would be much appreciated. 👍
I had the same problem. After a cocktail of cleaners, hair spray, acetone, isopropanol, and much more I cant remember It now has trouble keeping pieces on... All I can say is, don't use acetone, since that seemed to do the most damage. Nowadays I clean with Windex after each print.
Ive found the best thing to do is heat the bed after the print and it will make it easier to remove
Hello, would you mind sharing your start script for your slicer?
Does enyone have a problem with the chip reader on this 3D printer? I had the joy only one to print with it but then i couldn't manage to make the chip reader to actually read the SD card ... i tryed a thousand times and it s just annoying... i just recieved it today and i m already having problems with it
Can anyone help me, please!!
You sorted this right? Did you swap out the card to your pc to check it could read the card OK? BTW - I've had no end of problems with Win 10 USB / brand new micro SD cards being recognised as computer says 'NO!' 'Write protected'. Format it in your camera - was my solution after trying many other various software utilities and register hacks! Windoze! Don't ya jus luvit? Not!
If it's an Ender 3 dog, why's there a Makerbot logo on the bottom?
i watc hed your first vid with the unboxing ect i now have a lovely hole and deep gouge in my bed the 0.20 gauge should be used NOT paper im quite pissed perhaps You should do all the build ect box it back up and not go through it like you know! because you waffled though the vid
Way not level the bed manuel with motors off, so your Automlevel do not have to work as much...
this printer uses the capacitive sensor also for home point of Z axis,
since this system is not repetitive it will be impossible to calibrate this printer and print in the future without problems,
when the next day you print, you will have a different home point , so it will be impossible to print immediatily.
Every once you turn on the printer (almost always) you will have to repeat the procedure, which is very frustrating.
I have changed mainboard to my cr10s-pro, now every time that I light up I immediately go to press without problems, my first layer is always the same, equal to my first set-up
The lords of Creality .... instead of sending free printers to many people, should respond to support requests from customers who have bought their printers, they have never reply my e-mails.
A company can also make design mistakes (this is human) but if it does not respond to customers it will be a low-level company
This isn't a very clear video. Starts talking about actions halfway in.