I want to tell you how much I appreciate you! I've only watched one video of yours, so far, but it is one of the most clear, concise and strait forward video, of this type, I've ever seen!!! Even you voice is pleasant...Thank You!
I thought you did an excellent job, explaining the smallest details and what to look forward to when I begin my rebuilding of my pneumatic gun. I have three of them by the way.👍🏽👍🏽🙏🏽
Succinctly and clearly explained. Your remark about a "missing" part gave me some hope. I have a new, unused (apparently) Metabo pinner that I got cheap in an auction, which must have a manufacturing defect, as it leaks massively out the exhaust as soon as it is connected to the air supply. Depressing the trigger stops the leak until it's released again. I'm hoping it's a part missing or damaged on assembly, and not a casting defect.
@davidecasassa8679 get a rebuild kit! I'd replace all of the o-rings and such, but it sounds like it might be in the trigger mechanism (those parts should be in the kit). Good luck!
You mentioned many detail no one else had noticed , thank you . I rebuilt a senco finish nailer and replaced the only broken part ( that 3 had identified as the culprit and upon disassembly I found it was broken ) however upon reassembly I cannot get my gun to fire , , thanks for your video it was thorough and concise , ,well done sir and thank you
I have this stapler NS and the tension pin that allows for the staple housing to open disappeared. As a result the gun is now jammed. I have been able to find a pin that will work but I need to know how to stack the latch and pin back in place. The proper arrangement is imperative to gun operation. Please help do you have a film that shows how this is done Mr Joe 88yrs young
In your video the air was coming out of the exhaust cap of the gun? I have a porter cable BN200SB still new looking, used only a few times and the air is coming out of the exhaust cap as you connect to the compressor and its not shooting nails. I was told the BODY needs to be replaced. Can you advise me concerning this? Thank You.
@@TheTrullGallery Well the body of the gun has no crack, unless its a part inside. I however did see awebsite have a diagram of the parts for the gun and #301 is Body but I am confused. Thank you for responding also. I dont know how to send you the link for the diagram of the gun with the part.
The amber ring was the old ring and it was replaced with the clear ring you can see early in the video. If memory serves, it goes up near the collar at the top of the piston. ...I think.
Unfortunately the kits do not have "ALL" the breakable Plastic and rubber parts to completely rebuild it. In many cases the part that broke is not in the kit. You really have to tear down the gun and find the broken part and go through the PARTS diagram. Then you need to make sure the part is in the kit otherwise order the specific broken part. You are right about the correct kit for the specific model number. BN 125 kit does not work on a BN 125A, etc.
I have an old mini stapler that won't work. Model 2118/29. Probably 20 years old my guess. Has been sitting for 4 years unused. Now it just makes a little pup pup noise when I pull the trigger and it has no safety mechanism Because it was made that way. I opened it up to be sure there was oil lubrication and wiped it out but it's not working. I have googled this particular gun but no repair information. Anybody have any idea what I can do ?
I want to tell you how much I appreciate you! I've only watched one video of yours, so far, but it is one of the most clear, concise and strait forward video, of this type, I've ever seen!!! Even you voice is pleasant...Thank You!
@@JagermeistermasterJ thanks!
I thought you did an excellent job, explaining the smallest details and what to look forward to when I begin my rebuilding of my pneumatic gun. I have three of them by the way.👍🏽👍🏽🙏🏽
Cool, I hope I helped to keep 'em going!
Very well done! Now I'm less anxious about tackling my two non-firing Porter Cables.
Thanks! Just take it one o-ring at a time. Piece of cake!
Succinctly and clearly explained. Your remark about a "missing" part gave me some hope. I have a new, unused (apparently) Metabo pinner that I got cheap in an auction, which must have a manufacturing defect, as it leaks massively out the exhaust as soon as it is connected to the air supply. Depressing the trigger stops the leak until it's released again. I'm hoping it's a part missing or damaged on assembly, and not a casting defect.
@davidecasassa8679 get a rebuild kit! I'd replace all of the o-rings and such, but it sounds like it might be in the trigger mechanism (those parts should be in the kit). Good luck!
You mentioned many detail no one else had noticed , thank you . I rebuilt a senco finish nailer and replaced the only broken part ( that 3 had identified as the culprit and upon disassembly I found it was broken ) however upon reassembly I cannot get my gun to fire , , thanks for your video it was thorough and concise , ,well done sir and thank you
Thanks! And here I thought I was just rebuilding my gun. 😎
I have this stapler NS and the tension pin that allows for the staple housing to open disappeared. As a result the gun is now jammed. I have been able to find a pin that will work but I need to know how to stack the latch and pin back in place. The proper arrangement is imperative to gun operation. Please help do you have a film that shows how this is done
Mr Joe 88yrs young
@joealibrandi Sorry Joe, I don't. Have you checked the Porter Cable website? Sometimes, the parts diagram helps, too.
Good vid. Looking for kit for Cambell Hausfield HDN104 nailer. Any help would be appreciated
Try ereplacementparts.com.
In your video the air was coming out of the exhaust cap of the gun? I have a porter cable BN200SB still new looking, used only a few times and the air is coming out of the exhaust cap as you connect to the compressor and its not shooting nails. I was told the BODY needs to be replaced. Can you advise me concerning this? Thank You.
Without seeing it, I'd guess you have a bad o-ring. It's rare to see a cracked body, but I suppose it's possible
@@TheTrullGallery Well the body of the gun has no crack, unless its a part inside. I however did see awebsite have a diagram of the parts for the gun and #301 is Body but I am confused. Thank you for responding also. I dont know how to send you the link for the diagram of the gun with the part.
@pamelamohammed4551 send me the images at dave@trullgallery.com and I'll see if it makes sense to me.
What was that amber colored ring for on table.
The amber ring was the old ring and it was replaced with the clear ring you can see early in the video. If memory serves, it goes up near the collar at the top of the piston. ...I think.
@@TheTrullGallery thanks that’s the one I need for my porter cable BN125
Unfortunately the kits do not have "ALL" the breakable Plastic and rubber parts to completely rebuild it. In many cases the part that broke is not in the kit. You really have to tear down the gun and find the broken part and go through the PARTS diagram. Then you need to make sure the part is in the kit otherwise order the specific broken part. You are right about the correct kit for the specific model number. BN 125 kit does not work on a BN 125A, etc.
I have an old mini stapler that won't work. Model 2118/29. Probably 20 years old my guess.
Has been sitting for 4 years unused. Now it just makes a little pup pup noise when I pull the trigger and it has no safety mechanism Because it was made that way. I opened it up to be sure there was oil lubrication and wiped it out but it's not working.
I have googled this particular gun but no repair information.
Anybody have any idea what I can do ?
Sounds like a bad o-ring in there somewhere. The trick is figuring out which one. Then you just need to find a replacement...
How much did the kit cost?
That particular kit is going for just over $60 these days
Hola
I'm sure this video would have been great if he was actually filming his hands so I could see what he was doing.