"You are more right than wrong," as my late mother would say, when trapped for an answer, I watch your tutorials and listen to your advise, as I am considering a Pro printer when I can, but for the moment have an Epson XP-960 for which I sat there very frustrated in urgency to print and caught with a cleaning cycle, caught with likely over soaked pads, and more than two resets. So, what you say makes good sense and that when I can renew my printer for the 700 or 1000, I am now warned has been the source of my problems too. Thank you, I am learning and hope others realise you are correct and make saving on unnecessary ink loss that should realistically, be used instead on the next print.
Printer was a brand new Canon 3621 and for 2 years it did not work. I emailed Canon and they sent me new carts. Your video's instructions were straightforward; I followed them and voila!! it worked. Thank you again.
My experience is this: I don't use my Pixma Pro 9000 for days on end. It is set to "automatic" mode. It supposedly goes off when not in use for a number of minutes. Not really "off" but it is "sleeping". It is sleeping until you command it to print something and it will print usually without doing a cleaning cycle. It will, however, initiate a cleaning cycle when it is just siting there for a few days without my intervention because it was just "sleeping" not "off".
Didn't you just contradict yourself? ":It is sleeping until you command it to print something and it will print usually without doing a cleaning cycle" "It will, however, initiate a cleaning cycle when it is just siting there for a few days without my intervention because it was just "sleeping" not "off" OR do you mean if you print something withing a certain number of hours while it is in SLEEP mode it will not do a cleaning cycle unless it sets SLEEPING for days? I currently have all my CANON so they never sleep or auto off. That plus using them often will pretty much stop most auto maintenance. The PRO-9000 is ancient by comparison to the model I am talking about here. I have two 9000MKII sitting on my floor right now. One new and one with no printhead.
The inks were low on my Pro 200 and I started to replace them as they ran out, I saved ink and got extra prints out of it but it restarts each time so I now put them all in at the same time to avoid it, I also print a 6x4 every week or two and the head has not blocked so far. Photgraphy and printing is an expensive hobby but thats just the way it is if you want the best results. The best way to print cheap is to use a printer like the Canon MG5750 with non OEM inks i get decent results for not much money and if the printer dies it's only £50.00 for a new one, Iv'e had mine for maybe four or five years and it still works well and it's never blocked up in that time, leaving them dormant for months on end is the worse thing you can do to a printer.
You are correct. I have a 15 year old Cannon printer and when new, I could go weeks without the inkjets drying up. Now it is like 24 hours and I have to do a clean cycle. Mine does not go into auto clean mode. I think it is the design of the cartage. Face it, they don't make much if anything on the printers. It's the ink cartage's that are the cash cow. 30 years ago I worked for a company that made Fax machines. They had special paper that they basically burned the image on. No ink at all. It should be easy to do black and white and grey tones easily. Color would be tricky.
Canon IP7260 here. I replaced all the cartridges with refillable cartridges and the ink cartridges have worked fine and are still working after two years. I am using non-genuine inks meant for Epson inkjets because I already had 700ml bottles of them from 7 years ago when I used Epson printers. The colors look close enough for me--not accurate--but it doesn't look bad or wrong. Monitor is calibrated using EyeOne Match Pro, which is probably the most important step I have done. You can just keep manually adjusting the colors for your printer profile after each print until you are satisfied with the color-matching. However the pigment black is no longer printing as I stopped printing for a month. Perhaps it dried up & clogged the heads. Cleaning the heads doesn't fix it. My work around is to change Printer Settings to "High Resolution Paper" which will use normal black ink instead of pigment black. Best thing to do is save up for a second hand Xerox Phaser color laser printer. Sometimes companies sell them really cheap or even give them away for free when they upgrade.
All I can tell you about the Black Channel is that's what happens when one doesn't print fro a long time and Compatible and refillables are awful for CANON Printers. Pigment will clog quickly when not used often.
I think you are the one "expert" that really knows what he (/they) are talking about. I have been using Canon printers for over thirty years and presently have an MG6620 I have always LOVE the Canon printers. I recently decided to replace the print head (QY6-0082). I ordered one and when I got it, it gave me the error "wrong print head". It was clearly marked "QY6-0082" but only when I put the original print head (a QY6-0082) back did everything work.. Is it that there are varieties of QY6-0082s, or can the Service Tool allow resetting the printer to allow the replacement head to work? OR is there a combination of button-pushes that will do it? [and where can I find a reliable source of the Service Tool???) Sincerely, Dr T Rowe
WARNING! If you have short attention span problems do not watch this video. A lot of information here for a specific group of printer users using CANON PRO-100-10-1 printers!
I do not have that particular printer but I do appreciate you sharing your knowledge. In my opinion Canon should mention these default settings and incorporate the possibility to switch it off or even implement the possible to create your own printing schedule like you explained. To me this seems a really gray area, where the manufacturer profits from printers not being used regularly and then emptying cartridges by these programmed cleaning cycles..
They will NEVER do that. They want you to I've everything alone so you waste a lot of ink. Sad but true.
7 років тому+3
A quick story - I bought a 2nd hand pro 9000mkII on ebay . It was described NIB but when I got it , a few inks were done and the green channel was totally clogged. This was due to it probably sitting in a box for 2-3 years. I assume it was given away with a Canon camera purchase. So to clean the head I used NO solvent. But I did use an ultrasonic cleaner , hydrogen peroxide and a small amount of isopropal alcohol. half an hour in cleaner and testing it - the green now flows perfectly while on the test strip it was blank when printing green.. no lines or anything. Just make sure you take out the rubber if using alcohol.
Usually it's not recommended that you use an ultrasonic cleaner. It can actually cause internal damage of the internal delicate components. Also Hydrogen peroxide can cause damage. Most canon print heads need only need to be partly soaked in warm distilled water with maybe a bit of Windex mixed in. But you had success and one can not argue with success. Enjoy your 9000 MKII.
I've owned a Canon IP-100 for nearly 10 years. Best printer I have EVER owned! Although the "cleaning" cycles are annoying, the printer WORKS. Which is more than I can say for HP printers ( worst I have owned). Also own a Xerox Phaser MFP 6600. High maintenance ( not for the technologically handicapped), but with care, they work well. And no ink to ever dry out and clog print heads ( HP are you listening?)
Thanks for your great videos, Jose. Maybe I shouldn't have the puppy. I have had many Canon printers and have enjoyed making my own prints over many years. Over that time, I have replaced many printheads due to clogging. I was about to throw the whole idea of home printing out the window (along with the most recent printer.). But ....I got a Canon iP8720 last summer. My wife and I did our snowbird thing over the winter and took our truck/camper down to Mexico on a 5 month trip. In an attempt to prevent the inevitable printhead clog, I removed the printhead and stored it in a tupperware container. I used tye-wraps to suspend the head off the bottom and poured in distilled water with a little Windex. Not sure - but I think the liquid was just touching the bottom of the printhead. So 6 MONTHS later, I flush the printhead and reinstall it - sure enough - it's clogged. After 2 days of flushing, purging, using an electric toothbrush and cursing, I got it working. ........ I guess I can rant too ............. anyway: My question is this: Is there any way that I can go to Mexico and come back to a working printer? (Not going on the trip is not an option - otherwise I wouldn't have all the great photos.) - We do not have anyone looking after the townhouse - nobody is here. - Would it be risky and complicated to come up with a system for automatic printing every 2 days? (5 months = 75 prints) - Is there any way I can remove and store the printhead so it will not clog? I am sure other retired photographers are in this same situation - I look forward to your comments. Thanks ....... Dave
re. Inkjet Plumber, the Mac auto print app. I realize that the way to go is probably keeping everything together and just have my old laptop print out a swatch every few days. So Inkjet plumber MAY do the trick. Right now though the app will not wake up my laptop to perform the print. I don't want to leave my laptop up and running for 5 months. But I have contacted the author of the app and hopefully this situation will be solved.
Thanks yet again, Jose, for the candid and honest information and letting us all learn from your experiences. I look forward to learning more from you in the future.
According to the manual for the Pro 10, each time an ink cartridge is replaced, the printer is supposed to automatically run a cleaning cycle on the next print...so even for the frequent user this appears to be unavoidable. I've yet to verify this myself - just picked up one a few weeks ago and just now had to change one out for the 1st time, guess I'll find out soon. I've been running by the "60 hour rule" thus far. P.S. Thanks for your videos, several have been very helpful in getting me started!
Yes. One complete ( all 10 colors ) purge cycle every time you change one cart. Yes the 60 hour cycle is also part of the PRO-10. That is why I have two complete sets of carts. Once ONE cart reaches low, I exchange the complete set with reset and filled FULL ( 10 cart ) set. Once purge cycle is generated and I will will not be changing inks for quite a while. The single cart changing creates what we call " The Domino Effect " you are constantly changing carts and others that were near low.... will them BE low after the ink purge. The two set / change when one cart is low scheme, minimizes the generation of waste ink and preserves and extends the life of your Waste Ink pads. Ta change then reset the Printer will cost you more than half the printers original cost.
Jose Rodriguez Wow, interesting and good to know - thanks. With the talk of minimizing/avoiding cleaning cycles, it seems somewhat surprising that this part of it doesn't get nearly as much attention as printing frequency, etc. For me, the first cartridge to run out was CO (not a surprise), which I just changed out. I have not printed since changing it, so the cleaning cycle has not been triggered yet. The low ink warning just came on for Gray, and PB is about 1/4 full. The color ones are around half at this point. MBK is near full. Sounds like I should go ahead and change out Gray as well before I print again - and what about PB? What would you recommend? Thanks!
Officially that is never discussed as it is expected that NONE of us would or should be refilling with 3rd party inks. CO will be used at 4x the frequency to other colors. Grays are used a lot as well when printing COLOR. That is the way it is able to print super smooth gradations. You are on the PRO-10 so I said to change over when you hit LOW. Well that was a mistake on my part. Your PGI-72 carts do not have a sponge nor do they have to be modified in any way. Just reset and drip ink on the exit port till full at 33 grams. I do however exchange a complete set when ANY one goes to the empty or near empty mark. I remove them all and replace with 10 reset and full carts and continue printing. Then at my leisure I reset and top off all the carts I removed. One Purge per MAJOR cart change. No domino effect. SO you will need one more set of carts. Otherwise you will have to do each one at a time. Not good!!!
Ah I should have clarified - I'm not refilling my own cartridges (and don't have the equipment nor the space to do so even if I wanted)...just buying them the old-fashioned way - direct from Canon. I have an extra set of all inks plus 3 COs. Ordered a Gray and a PB last night. Would like to maximize ink usage and minimize cleaning cycles so trying to figure out when it's best to switch tanks.
I use my Pro-10 a lot (several photo prints a week) so the few times I'm away and the printer goes into a cleaning cycle I consider it a good thing. I just love the photo prints produced on the Pro-10. (If you use Precision Color Inks the cleaning cost is negligible. Other than for photos I have very little need to print in colour. My networked Brother (black only) laser printer has been a real trooper over the years.
Wow. That is a big deal. How much printing does it take to reach this point? And do you know if there is a "meter" buried somewhere in the drive/software that keeps track of how much ink is used?
It's not how many prints it takes but how may For a ing cycles and I'm purges generated after EACH cart change. That ink is directed to the pads at the very base of the printer body. Totally inaccessible to you. The firmware keeps track and when a certain arbitrary Magic Number is reached, thats it. The printer stops working. It's not just the pro-100 but ALL printers with internal waste ink pads. There are tools for resetting most Epson printers but not Canon, but the ink is still being accumulated in the pads and eventually you overflow.
Your videos that I have seen are very informative and useful. This one made me realize that a printer at home for say 13 x 19 prints just would not get used enough to justify the costs of ink. You mentioned Qimage, which I have supported for over 10 years (for when I need to do a print) and I know ice profiles for the printer at COSTCO near me can be downloaded. Could you do a video step by step workflow for exactly what needs doing to get the best results? That would really help me.
Are you talking about you printing at home or prepping for COSTCO to print for you? If so they would be using the paper profile and not you. You would process as prep you images as you normally would. No special secrets that I know of.
I own a Canon i960 inkjet printer (ca. 2004). I don't print everyday and usually it goes like this... I "re-discover" my printer and start using it for a few weeks. Then months or even years go by and I ignore it. Still have this printer and it works flawlessly, as long as I use the 3rd party Linux driver TurboPrint for it. I get 1200 dpi (fine mode) under TurboPrint, where I only ever got 600 dpi from the CUPS-Gutenprint driver. My housemate friend on the other hand bought his Canon i960 in 2007 and must have used it constantly. He tells me that the printhead wore out and the printer is no longer usable. Sure it does the nozzle check and must have wasted some amount of ink since 2004 and perhaps I've had to purchase more ink more frequently than otherwise. But if I don't print that often anyways, to me, it doesn't really matter. I don't wanna hafta search for some image or document to print to keep the it from doing the nozzle cleaning. I love the look of my i960 and the fact that it just does printing. Not scanning as I have a Canon LiDE 110 for that. No use for fax but I do have three places I could go if I need to fax something.
SO what you have discovered is simply this: Older CANONs are built so much better and perform so much better than our newer models. It is sad but true. Since you print so sporadically as you say only after you rediscover your printer, it is not using any ink during all that time so even with a cleaning cycle it still is not wasting a lot. But my current advice is for folks who are photographers and print much more often than you but sometimes not within that 60 hour limit. They will pay for that with a cleaning cycle. Now about the print heads. Canon print heads are thermal and basically are self destructing themselves as they print. But a print head for a PRO-100 is only about $70 so who cares!! Plus they are user replaceable!
Well that explains a few things. I have hardly used my Canon printer at all, and it's already telling me "low ink".And all the "cycling" it does whenever I turn it on. It's a 3600 series, and for what I use it for, I spent too much.
PRinters are so cheap these days , and carts readily available. But it's become a throwaway society, As I remember 10 - 15 years ago - people buying printers second hand just for the cartridges because they were now an obsolete and the quality was so good.
Dear Jose, I have enjoyed watching your videos and learned a lot from them. I had a Pixma Pro-9500 which worked fine for around 5-6 years (I can't remember exactly how long) I did not use it that much because of the cost of each cartridge and I now realise that this was false economy. Eventually the print head clogged and I could not unclog it so I replaced the 9500 with the Canon Pixma Pro-100s. After watching your videos (which all seem to have referenced the Pro-100 and not the 100s) I thought I knew how to do things right. I keep the printer on all the time and I make a print every two days. Sadly, the 100s seems to keep carrying out cleaning cycles, even today when I made two batches of prints it seemed to carry out a cleaning cycle before each session. Do you think that Canon have heard about your videos and changed the firmware so that the 100s is scheduled to do more cleaning cycles and not just after every 2.6 days?
Thank you! Most people HATE this particular video. Apparently it's too long I don't get to the point in one minute. So I really appreciate do that you like it.
This is true of non photo grade canon inkjets as well. You really have to run a print with them every other day or the printer will go through a cleaning cycle and you will waste a lot of ink. I just use the inkjet as the primary printer with one of the computers I use every day. The lazer is faster and less expensive to use but you have to exercise the inkjets to keep them happy.
I use my inkjet to print graphs 90% of the time because the color makes it easy to differentiate between the plots. Also most people own inkjets just for printing documents but some do let their priter sit fallow for a week at a time and then complain about excessive cleaning cycles and high ink usage.
Well using an inkjet for just documents just doesn't make any sense! Unless you use it daily. One of the reasons is printers of that lower caliber are practically being given for almost free and the cost of inks hits you. Their response is...What, you didn't know?? On other hand if I have a high end inkjet that I use to create prints for sale and it cost a total of say $20 including paper and waste ink generated but I sell it for $100, then that makes sense to own that type printer. Using it for printing emails or web pages.... No way! People need to look at the situation that way. Inkjet technology is finicky as hell. When I worked wit drafting pens the various diameter would constantly clog and practically lived in the ultrasound bath. My fault for letting them dry from lack of use. Same thing applies to inkjets.
I had a canon printer that went thru the mentioned 2.5 minute cleaning cycle every time I wanted to use it. Threw it out the 2nd story window. Life is now good.
Actually, I was using it quite frequently. Bought it new and it wasn't cheap. After a few months, it would error after the clean cycle and recommend yet another clean cycle. No matter what I did, it never resolved itself. That was more than 15 years ago. After all these years, hearing people are still dealing with annoyingly long clean cycle on Canon printers, makes me feel glad I thru it out the window and never bought another canon printer since. I've owned other brand inkjet printers since, they are fine, even after long periods of non-use.
It was a long long time ago. Late 90's Model was something like BJC-3000. I was highly disappointed that issues like this still exist with this brand today. Glad to have steered clear of this brand printer ever since.
DIY: get epson, gut it till it still works, buy a kit that lets you connect print head to large bottles of ink via thin tubes, and well have it gutted so you can manually clean the head if it gets too clogged. That's how i printed commercials/flyers etc for years. And you can feed it cheapest ink you can find on the Fleabay. I even printed with food colour dissolved in filtered rainwater (too cheap to buy distilled - i need enormous supply of demineralised water for my aging offgrid forklift lead acid battery ;-) and some generic window cleaner to lower surface tension (the one that had least pungent taste, no ammonia, which i thought has least corrosive stuff in it - questionable technique, but i don't have a gas chromatograph / mass spectrometer...for now;-) The food colour bleaches in weeks/months, but who cares for flyers that will be outdated in few days...
Pyroslav x: I don't know if you have a UA-cam channel, but you should! Sharing your experience offgrid and with printer, food colour stuff would be awsome!! AND you might make some little money as well. Have a nice day dude.
I use my MP630 every few WEEKS. After a clean the cartridges are nearly empty. If I renew ALL the cartridges, print a few pages and don't use it again for a few weeks then the next time I use it it will purge and half the cartridges are empty again. I would say I get about 10-15 pages per COMPLETE SET OF CARTRIDGES. That's CMYB+large B !!!!!
Yes sure! That is what happens when you only print every few weeks. Cleaning cycles that initiated due to long periods of non use will empty tiny carts quite readily. That is what happens.
Hey Jose, I'm new around here but your channel is great. Question: You made a correction in the video info saying that the canon pro100 will do a time cleaning if you print or not, but then say that you should print every two days instead of let it do the cycle. So that confused me a little. If I print every two days will it stop the cleaning cycle after 120 hours or not? I don't want to waste ink. Thanks.
The pro 100 has timed cleaning cycles that will occur on your next print job after you exceed 120 or 480 from your LAST CLEANING CYCLE! SO if you print right this minute and you had not printer within the last 120 hours that print job would be preceded by a cleaning cycle because you had not printed within the last 120 or MORE hours. If you print anything within that 120 hour window no cleaning cycles will occur until you pass 120 hours. If you have not printed for 120 hours the cleaning will be medium and if you have not printed for 480 hours the cleaning will be larger. How much ink do they use? No body knows.
It sounds like you are new here so I would suggest you search my Playlists for TONS of PRO-100 and related info. Here is a video where I cover the subject you are asking about. ua-cam.com/users/edit?o=U&video_id=LlZQj1uGqq4
I was wondering about your opinion on something. I have an IPF 6300 and I am now experiencing issues with my second set of printheads. I don't print enough and I have not been good at running nozzle checks and test prints to keep the nozzles from clogging up. At the present, I have ink in the machine and two, unopened printheads. I am talking to a retailer about getting some cash back for the print heads and putting that towards a newer, smaller printer such as the Canon Pro 1000 or the Epson P800. The alternative would be to keep the 6300 and use the new printheads. My goal is to have a more trouble free printing experience based upon low volume usage. What do you think?
The P800 would be your best choice for not often printing! But you must know how I feel about that! If I am not committed to use my printers at least once a week of more often, then maybe I should.not own one. But that is just me. The P800 will be more forgiving. But not the Canon printers.
I realize that regardless of how I go forward, that if own an inkjet that I will have to commit to a routine of maintenance prints to keep the printheads from clogging. It is interesting to me with the amazing level of technology in these machines that there isn’t a more effective system of self cleaning built in to these machines.
There is. It's called Auto Cleaning Cycles and CANON utilizes it. How are you going to keep tubules that are only 1 micron in ID clear of something that is not only fairly viscous but also containing solid nanometer size pigment particles in suspension. The only way it to forcibly suck out ink with the purge pad pump.
Thanks so much for the useful videos! I just bought the Pixma Pro 100 and they have been a big help. Question, in the short term, is simply printing a nozzle check sheet every 50 hrs enough to keep the cleaning cycles at bay?
Yes. Any print job. You want to break the idle period before 60 hours. So anything you print will break that will Interrupt the period of that idleness will do the job.
The PRO100 will trigger a pre print cleaning cycle after 120 hour of not printing. If you go past 480 hours it will run a larger cleaning cycle before it begins to print said job. Then the timer resets to zero and youncan print without cleaning cycles fornthe next 119:59:59 hours before the next cleaning cycles is added before the next print.
I had that problem with inkjet printers from many different brands because I only print something once every few months... Leave them on, and they clean themselves until they run out of ink, and they're out of ink when you go to print something. But leave them off and the ink dries out and clogs. But don't call me cheap because I can't be bothered to print a blank page every two days to keep the ink jet clean. That's a ridiculous thing to tell people! My solution is that I bought a color laser printer. A laser printer doesn't have this problem. A laser printer can sit idle for _months_ between prints without a problem. If your problem is you don't print often enough and your inkjet clogs or runs itself out of ink cleaning itself, get a laser printer...
And I agree with you 99% except for one thing. We are talking about Photo Printing Printers capable of high quality art prints. which lasers simply can not produce. If you do graphics, text, brochures, graphics and even photo album pages then yes get a good Color Laser and don't even consider an inkjet printer. Id your be totally nuts to buy a 12 color inkjet printer meant for the production of collector level prints unless that is what you will be using it for. For everything an inkjet printer is not your best choice.
Not all brands or models do that. HP and Canon are famous for wasting your ink. I have an Epson XP-610 and use it rarely, I have never seen it go through a cleaning cycle before printing.
Inkjet costs too much per page anyway. Yes,it is a tradeoff in machine purchase price and cost per page. 10 cents per page inkjet vs 2 cents for laser. Photo print quality,the price goes up for either method,but inkjet is ridiculous.
The comment above about waste cartridges is untrue. Before your waste cartridge runs out of capacity turn off the printer and take out the waste ink cartridge. Go somewhere where there is water and you can make a mess, take out the screws on the waste tank, open it and remove and discard the absorbent material. This can get messy so have your trash can right next to you and wear your painting clothes. Once the padding is removed, fill the waste cartridge back up withpaper towels or similar absorbent material. Big box stores sell a heavy duty paper towel for working on cars and similar things for about $2 and it works well. Close the cartridge up, put it back in your machine. Go to service mode by pressing load and navigate while powering up the printer. Once in service mode, go to the adjustment menu, then to initialize and down arrow until you get to W_Ink (waste ink). Hit the OK button. Power down your printer. When you reboot your printer, the Maintenance cartridge will be reset at 100%.
Have you actually taken a look at the PRO-1000 waste ink.cart??? It is a sealed unit with no screws as you suggest. And even If you could.do that, would you reset the chip???? Huh?? You can indeed do that with the Epson large format printer's waste ink.carts but absolutely Not with the Canon PRO-1000 and up! unless you know something I am not aware of! Good Lord, just pay the $15 and spare yourself of the mess of repacking a waste cart. Like I said I do it on the PRO-3800/3880 and P800!
I just 're dead your comment as you might receding to.other Canon printers with internal.pads. Are you suggesting a regular person to.do the pad replacement? Then process you suggest works with older printers but not the newer ones. Firmware updates no longer allow you to.enter service mode unless you then log into the Canon service server and have a unique password.and key. As you an authorized service tech???
It works with my IPF 6300 and other IPF printers, which do allow you to enter service mode. I can't imagine waste all this ink with cleanings and having to purchase waste ink cartridges too, sounds even worse than the IPF printers.
Yes you indeed can do what you propose on those older printers but such is not the case with the new line of IPF PRO models from the 1000-2000-4000-6000 The Carts are hermetically sealed and Totally seamless in construction. The only entrance is the waste inlet port and there is s mall rectangular felt pad that allows you to see when it reaches saturation. It is a 100% throwaway product. And no you can not enter service mode as I said on these newer printers.
Hello, I have a canon MX922. I have tried everything from cleaning the printhead, resetting the printer, adding new ink, even putting paper in the upper paper holder. What is the deal with these? I see this was a problem way back in 2017. What will solve the issue? Its grabbing the paper, acts like its printing, sounds like its printing and the page comes out white.....
Hi Jose , I've seen a few of your vids, more specifically around the canon pro 100 and they are very informative. I decided to purchase one today as I'm trying to turn my hobby into something more. While that happens I'm rediscovering printing having been out of the game for 12 yr-ish. I plan to use the printer but I wouldn't be surprised if I don't print every 2 days...I'm throwing this question out there to you as you have a handle on the ins and outs of printing. If you know you're not going to make that 60 hr window, and know that say you maybe will not print for 2 wks or more....could you remove the ink carts and store them so they would not dry out? Then slap em back into the printer when the need arises? Thanks again for your vids, keep em coming! Mark
Sure but the internal timer will run a cleaning cycle p!us the fact that removed and reinstalled the carts will force a large Ink purge. There is no way to avoid the inevitable. You just have to print semething. Anything will do including a simple nozzle check.
It's not just the pro printers that do this - even the cheapest consumer printers run autonomous cleaning cycles. A print a day keeps the ink waste away..
Hi Jose and congratulations for the excellent work. I print black and white 99% of the time (with the option print in b&w selected from the printer's software) and I wonder if I use all my inks, or just the monochrome ones, Basically I need to know if I still have to run nozzle checks within the 60 hours window, even if I print b&w prints in intervals shorter than 60 hours. Thank you in advance for your answer and best wishes for a healthy and happy 2017!
I can't say for sure whether printing in B&W mode uses only black and grey inks or a composite of all colors. I think not. B&W seems to basically just do an on the fly file conversion to B&W at the driver level. To try to answer your question concerning printing within the 60 minimal.period. Anythng you print will count. However there are reports of other types of noises occurring before a job begins to print even under the 60 hour period. Its hard to determine what the printers are actually doing.
Jose, is there any reason my Canon pro 10 can not print a 13 x 38 inch pano print? When I set it up the paper size and print, but it places the image going the wrong direction. I changed the orientation, but it still prints only a horizontal strip of the pano image. What can I do?
I confess to being confused. I wish you had pointed the camera at the printer just once. Are there really $1000 Canon printers? What does it do to be worth that? I bought a Canon Pixma 3600 series printer at Walmart for $40 and I have printed documents in color and black and white and even 8.5" x 11" photos on photo paper and they look great. It also scans and I have digitized hundreds of family photos into my computer. Never once has it done anything on its own or run a cleaning cycle. I'll admit the cartridges are a bit pricey ($60 for one of each) but I haven't kept close track so I could break it down by page. So, why $1000 printers?
Those $60 Canon Printers are only letter size paper capacity and so that limits it as far as creating LARGE prints which is what you pay the extra bucks for. Unless you use third party inks the inks would cost you 2x the price of the printer and that is why they are priced so cheap. The PRO level CANON Printers we are working with will range from $400 to Thousands of $$$. The technology is many fold more advanced and is meant for truly professional production work. The one next to me is the PRO-1000 and it retailed for $1300.
Jose, love your videos and just purchased a Pixma Pro-100 printer. Can you share the details on the "un-clog tool" and scheduling software that you discussed in this video? Much thanks!
I am surprisedat the number of users here that don't seem to understand that when you talk injets vs. laser it's apples and oranges. For high quality photos you need ink jet, for documents you don't.
Thanks very much, but I just ordered a Canon TR7520. Would this be the same routine for this series of printers? If not, what can you offer for keeping it from clogging when I get and start using it? I think I have found a good ink supplier that gets their ink from a US manufacturer and is supposed to be formulated to the same specs as OEM much less expensive. Ink Owl is who I am considering for the ink. Any advice for me? Thanks. I enjoy and have seen some of your videos before and they are very good. I can tell you really love your printing.
Yes the routine would be the same. But the times cycles would be different and No one knows what those are. Ink Owl inks are made by Image Specialists who was bought by a Florida based company. And no. No 3rd party inks dye or pigment match oem 100%.
I didn't say that. You want to save a lot of money? And don't mind losing a bit of quality but still want to the print? Then by all means. A good paper printer and ink profile will get you as close as possible but not exactly. So you can't have your cake and eat it too.
That'll work for me. I am not an aficionado and probly didnt even buy the best printer for my needs. I will be using it to print flyers for my business now and then and mostly text documents. I was gonna get a Canon Maxify but I think that one will only use pigments which I dont need. I really wont be printing alot of pictures. Just once in a while. I had an Epson Workforce which was a nightmare after one year. I had one previous to that one and same thing. So i thought I would try Canon. I purchased 3 refurbished Brother Laser 9130CWs for my business. Every one of the Brother 9130CWs would leave toner smudges every few pages and would also come off on my hands. I had to return them all. That would have been my printer of choice for my needs. Was very disappointed. So I'm back to trying an inkjet again with Canon which I never owned before. Thanks again. You are a great resource and I subscribed.
Hi there nice review, so what do you make of Epson Eco Tank printers. Would you recommend that for some one serious about photography And want to print photos. Many thanks.
If you want to pint photos then you need to get a Photo printer and not an Eco not l. They use cheap low longevity dye inks. These Pinter as for quick document printing on plain paper such as you would need in an office situation and you need some quick flyers. Don't believe the claims from Epson.
Ok. I just cleaned my pads myself, for free. My hands are dirty now but if i wore nitro gloves they would not be. so now I got this. I just need to print something, even a check heads test sheet every day or two and I will be all good. Oh yes, and I do not need a puppy. I don't pay squat for ink, this is why I love my cannon.
I have some directions here that I got off line but they do not seem to work, what I ended up doing was by passing the error by just clicking OK. it did come up again and I did the same thing I just pushed OK on the printer. The error code went away and the printer continues, i guess it may do that every time I shut it down and power it back up. it is working though so no biggie I guess. The instructions I got were like the damned Hokey pokey dance, they didn't do anything it seems but waste my time. i will keep looking though, if for nothing else but to save the extra clicks LOL Oh! those pads were easy to clean up, I used a little dawn detergent and hot water from the tap, I kept ringing them till the water ran clear and then I flattened them out in paper towels and set them on a rack in my oven on proof. which is 100 degrees worked great. the inks light right now, I took the head out and cleaned it the same way , I think it will get darker after a few prints go through. i was looking on eBay while my pads were drying and I saw print heads from China for that use ONLY BLACK, I wrote to ask how they work, that would be a huge money saver for me.
Hi, Jose. I've heard you often speak about the timed Canon cleaning cycles, 60 h, 120h, 480h. You say that if one prints before the timed cycle "your ink will go to the print and not be wasted on a cleaning cycle." I'm confused by that statement. Do the cleaning cycles occur even if you are printing every day, or does printing "reset" that cleaning cycle clock so that it does not occur until the printer is idle for the 60, 120, 480 hrs? Thanks
Okay. We now know that printing those not disable any of the cleaning cycles that occur. Pigment printers like a pro 10 will run a cleaning cycle every 60 hours whether you print or not. The pro 100 being a dye ink printer has a longer. 120 hours again, whether you print or not. Please go to my video list and look at the very recent one that I did a few weeks ago it explains everything We now know about the maintenance Cycles at the Canon printers run.
Dear sir. I have the pro 10, and expecting to receive a pro 100 soon. They are such a good value to be passed by. Just a casual check. Do you think the chassis of the pro 100 is the same as the pro 10? You think if a pro 10 print head is inserted into the pro 100 chassis .. and perhaps unlocked it's use as a pro 10? They are so similar that it seemed plausible that Canon could be manufacturing the mechanical parts as the same design, whilst having a different firmware for each model will bring down their manufacturing costs. If this hypothesis is true. We may just have a cheap chassis for replacement in case the ink pad (irreplaceable) becomes saturated.
I'm pretty sure that will not work. Both printers PRI t head carriages are different and so are the heads. The chassis is internally also different as is the motherboard and firmware.
Jose, could you answer this for me? I want a large scale printer (13x19) to print on 140lb watercolour paper, pretty much only in brown ink (the line art must be waterproof) and the printer would be sitting not used much of the time. I could buy a used epson r2880 (found one used for 250, but how old is it?l and might sell today) or a new Canon Pro 100 ($400 by payment plan)....could you advise what printer I should buy and things I should take into account? The essentials: waterproof ink, large scale that takes heavy art paper and will sit not used, but I could only use brown line art ink. Under $600 has to be, can't afford more
I don't know of any Brown ink for any of the common printers. You would have to custom mix ink compatible to EPSON photo printers and load cartridges with it! So for instance with the R2880 you would need 8 refillable Carts loaded with this custom ink. Theoretically should work.
I like canon printers, but i am away for long periods from home like a month or two. What do you suggest me to do about my ink cartridges? Should i move into a laser one?
So do i need to leave my printer on and plugged in? I have a Pro-100 which I do my best to use every few days, but every time im done printing I turn it off (still plugged in, just pressing the power button). I've noticed that when go back to turn it on and print the printer will make some noises for around 30 seconds. Is this the cleaning cycle you are mentioning?
Yes. On 24/7. You can prevent the cleaning circles that take place whenever you repower on the printer. But you cannot get rid of the cleaning cycle take place for normal maintenance but at least you can reduce or eliminate the ones that would occur when you re power on so leave it on 24/7
If I was talking about office Printers then maybe but I am not. I am talking about dedicated pro level photo printers and not document types. If you print non photo document then a simple cheap laser will fit your needs better. I am talking about a totally different class of printer here.
hi, i have an old (circa 1990) Canon Bjc-250 printer, very good, that worked very well for me and uses Windows XP. The printer worked well until 2017, when, one day it stopped printing altogether...when i send the command "print" (in black and white, that is all I do...)there is total silence. Before this , at the clicking on the "print' word, there used to be an immediate whirring sound and the pages would start being printed quickly. when the problem started i bought a new b&W cartridge,installed it, and again clicked on "print", but there is a total silence, nothing happens.....could the cause be that microsoft stopped supporting the WINDOWS XP around 2014/15, and then this cause my BjC-250 stopped working forever?
Thanks for the awesome video. Just purchased my first Canon printer, an MX922. Looking forward to long life. Just curious, did you ever find a way to trigger a nozzle check from a PC?
You can trigger a PURGE print but you need a script which I do not know anything about. But Qimage Ultimate, the print layout tool will allow you to PRI ta scheduled color Purge print on schedule.
Coool... Thanks for sharing your experience. As an aside... Google is awesome!!!! Without Google, I never would have saw your wonderful videos.... In either case, thanks again and I am going to eventually get a Canon printer, but I am wondering what sort of upgrades would be in store for the second version of the Canon 1000. Will they make a second version that would still be desktop, but can print 24 inches? Will they address or present an alternative method to their anti-clogging feature? It will be interesting. I am actually thinking about just holding off to pay full price for whatever the second version of the Canon Pro 1000 may be. In either case, have a nice day.
I don't really anything of a desktop 24" model. The PRO 2000 already covers those features except for being a floor unit. This one uses roll and cut sheets. The PRO 1000 still has a length limitation.
Thanks for your kind and prompt response. I actually just received my Canon quote yesterday for the Pro 2000. But the more that I thought about it, I love the concept of the desktop more so I decided to pass on the Pro 2000. Maybe I can upgrade to that one later if I never get what I want in the desktop version. I just wished the Pro 1000 could print 24 inches. I am not too concerned about length as I am primarily printing portraits and likely some landscapes. I just figured that by the time that I have the money for the Pro 1000, maybe they will have a second version of it out. I was curious on what that new version would be. Could it be 24 inches in a desktop environment? I know some may say that they would not risk galvanizing their Pro 2000, but a I just truly see the products as different. Ooooooor could it be something truly awesome such as larger ink carts going from 80 mL to 137 or 200 mL which I believe are in the larger models. Pay me no mine... I was just brainstorming what the ideal next version of the 1000 would be. It seems that a number of big companies have gotten in the habit of upgrading their products about 18 months to 24 months. Which means... That is too far away since the Canon 1000 was released. By that time, I will be ready to buy. In either case, thanks for your kind response. Talk to you soon....
You can buy the pads on ebay and replace them yourself. there is no magic key to open these printers and the pads are user replaceable if you learn how to do it.
Sure! Easy for you to say! If it was that easy everyone would do it. Also the new Canon models require you to log into the Canon Service Server and also have the service tool. Do you have the password and serial key for the server??? I don't think so!
Hey Jose, so if I turn my pro-100 off after printing is that worse then leaving it idle? Or is it just unplugging that's worse? I've been unplugging my printer every time I use it as I needed the socket :(
No need to ever do that. Unplugging will waste more ink when you decide to printer next time. The idea of turning off printer is antiquated and no longer relevant with today's modern printers.
Hola Jose, no se si me podras entender pero de igual manera te pregunto. He visto varios de tus videos pero no he encontrado la solucion a mi problema pero me han servido de mucho. Tengo una pixma pro 10 y cuando imprimo en papel tamano 4x6 al final de la impresion la foto queda descuadrada. Justo antes de terminar de imprimir la impresora como que hace un salto y la impresion se descuadra. Me gustaria mostrarte las fotos de como queda. Porque pasara eso ? es posible que sea el papel ? Tengo fotos de las fotos por si te gustaria mirarlas. Saludos
Estas usando paper brilloso? Canon, o otra marca? Creo que los rolos de transporte estan resbalando. Corre el proceso para limpiar el.Paper Transport que we encuentra en el Maintenance Tab.
Jose, te agradezco muchisimo que me hayas contestado. Si, es papel brilloso, es otra marca y ese papel tenia muchisimo tiempo guardado y como justo compre la impresora lo use. Cuando imprimo en papel brilloso tamano carta si imprime queda perfecta la impresion. Es posible que sea el papel ? Como se corre el proceso ?
Aca te dejo el link de como quedan las imagenes. Solo sucede con papel 4x6. wetransfer.com/downloads/3aa62a0e899ef19565f75278d57deb2b20180828195903/8c68313db33f131a61569ee7e5ee44ea20180828195903/0b75ce
Si no es CANON puede que sea demaciado resbaloso i al final se muve o se mueve. En el Driver se va a "Maintenance / Roller Cleaning" i siga las direcciones. Si eso no lo arregla el problemba tendras que usar otro tipo de papel. Que Marca es?
I have an older Canon MG8220 Photo printer that has 9600 x 2400 dpi but only prints out a 8 1/2 x 11" borderless max. It prints out beautiful pictures, so my question is about the Canon Pro 10. Would it print out pictures that would be considerably better? By the way, I can clean it through the maintenance program, all done manually. It can sit for months and no problems with clogging. The front right side paper tray was broken by someone but it can still be positioned to work.
If you are just getting into this I would forget about the PRO-1000. That is a production printer requiring daily use with lots of large prints or you will use more ink on maintenance cycles than on producing prints.
Thanks for taking your time to share your advice. I was leaning towards the 10. Does the 10 require a lot of usage also or will it also perform maintenance cycles after 60 hours of non usage? You may have stated that in the video and if so I apologize for not remembering.
Thank goodness for affordable laser printers! Life got so much better when we threw out our HP ink jet printer. Never could figure out if HP's protectionist ink policy was more akin to armed robbery or extortion.
Jose Rodriguez We were slow to realize laser printers had plummeted in price. What little color printing we absolutely must do, we do through local printing and photo services. Grayscale pinch-hits for everything else. Brother is the brand we went with. Figured we'd feathered the nests of enough HP executives. Very happy so far.
Dear Jose, just discovered your video channel. It's clear to see you are an expert on printer problems. However l suspect many people just want to print off occasional bill receipts and photos et, not professional quality
That is why I do not deal with document type All In One printers. This channel IS about Photo Printing and photo printing and NOT about once a month printing of a bill or envelope.
Jose: Just got the Brother Mfc-J5830dw. The inks are claimed to be archival by Brother. As expected, they say you need to use their paper. Does the type of paper you use effect the archival quality of the ink? I intend to use QEM ink only as I will sell 11x14 pics. Thanks Charlie
Yes Paper is just as important as the inks themselves. But you know that printer only uses four colors and if by prints you mean Photos, that is not going to work very well as far as color fidelity of your prints. The gamut will be quite low even with OEM inks.
Of course. You are not supposed to turn it off and on. That is what it is programed to do. Leave it ono and print every other day and the ink will be used for the creation of prints.
Is they a flashlight looking. Spring in with the scanner arm if so where does it go I replaced glass in my canon 6820 puxma and seen a spring rolling around in there since the glass was broke I wasn't sure if it was to be in there also the arm won't return to scan goes all the way left but will not return to take copy
I am sorry Debbie but a printer mechanic I definitely am not. I can teach you how to print great photos 24 / 7 though! If the printer is worth it you might want to take it for servicing. Obviously something mechanical has broken in the scanner. I hope the printers is still able to at least print.
This may be too old to ask, but do you have expierience with the IPF755, The other day I turned it on and booted straight to an error, So did a reset, Navigation+Load+power. Got into service mode. everytime i try to load paper I get a code 2f14, 2f13,2f2a, Can't figure this out, i use it to teach a graphic art class to students that can not afford a vo-tech, So I pay for everything, any ideas on what to try
Sorry Mark but do not I ow that model. Have you googled those error codes? Often after a lot period of non use they tend to through errors. Pull the p!it for about ten minutes, re plug and re power and see if that works. Otherwise, I'm afraid there is not much one can do with an old printer like that.
Hardly any. I have an old AIO Epson Artisan 720 that would print to disks and had a user replaceable waste ink cartridge but it no longer made. None of the photo level printers will suffice. Look at the Expression series and see if they offer both of the functions you neee.
Yes. Computer and printer and Qimage as well. Remember this is only keep the printer exercised and reduce the chance of logging. CANON's timed cleaning cycles will still occur regardless.
I have a Canon printer. I hate them. They keep changing to all colors. I do not do any photos. I only print documents. I have to keep buying color carriages.The printer reverts back to all color to make black print.
Printers must use all color to print ANY document whether is is composed of only black or not. My recommendation is to get a laser printer since you don't print photos.
Hi Jose can you recommend a simple budget printer where mostly i print black and white doc, bills and pictures (borderless print) from my hand phone and for home use only. I use to have a printer but i hardly use it this time i planing to get borderless printer to print some of my picture taken from the hand phone. Jose can you suggest me a one please, thank you.
I guess what you want is a all in one type printer. The problem is I have no idea about any of these model since I only use and work on larger Photo Only Printers. So I would not know where to even begin to suggest one. Canon and EPSON has goo AIO printer that also have scanners built in. Usually about $100 and up. Look for something that has WiFi so you can print through the smart phone.
The only time I recommend using a glossy photo paper is when performing AUTO nozzle checks or AUTO print head alignments. These AUTO tests require that the printed results be scanned and analyzed by an internal sensor. These results are sharper and easier to detect and be read by the sensor when printed on glossy rather than copy paper which wicks ink a bit more. Only some printers have these features. For simply printing nozzle check or purge charts you do not need special paper.
My low mileage canon mb5320 printer: Power light stays ON forever, the yellow light in the triangle stays ON as well. The printer is not working, the display window has no light ... totally blank. Canon tech asked me to replace the printer. Any tips?
It may be low.mileage but it is old.and printers so. called duty cycle of d# of print or # of years before they are done! Mileage is less important than time. I have two Epson pro3800s both ma y years old. One is still.working fine with 17K prints under its belt. The other one is the same age but died at about 5k prints. One has used heavily and one was not. I am nervously waiting for the other one did soon but at least I got a.to air prints out of it. So the bad news is that the tech for once is probably correct. Ultimately printers will succumb to time especially when not used often.
I have a Canon Pixma MG2920 printer I have replaced the ink cartridge several times before, but have just purchased 2- 245 Black cartridges and it keeps giving me an error that the cartridge isn't installed properly or is the wrong cartridge I have tried everything I can think of and when I diagnose and repair it says there is no problem
Jose Rodriguez I hve a question ,which printer do you think is the best and less expensive to use I do not print on a daily basis..Here are 2 I was searching on Canon Pixmz TS9120 or the Canon Pixma G-1200 mega tank injet printer...Are the mega tanks better and cheaper? Curious on what you think
You are asking the wrong guy but, generally The Megatanks G class Canon just like the L series from EPSON will be more economical to operate but they cost much more from the start. The truth is I do not use ANY non PRO level Photo Printer so I can't give you a direct answer from actual experience.
Thank you so much for the information. I am getting ready to set up my Cannon Pixma Pro-10 that I have had sitting in the corner for about 2 years. I hope the ink has not hardened up!!! Silly me! Now I have subscribed to your channel and I am looking for your Patreon.com or I have tried Patrion.com to look for your website, and I just can't find it. Oh well. Again, Thank you so much for all of this wonderful information!
My Patreon link icon on the main channel page on the lower right of the channel art image. But just is case the URL is www.Patreon.com/jtoolman Thanks and don't forget to join us tonight at 6 pm EST USA for the first live stream of the year.
Hello Jose, I have a sudden strange problem with my canon pixma mp530. Basically, once Printing the noozzles pattern test, it comes out only exactly half of the grid created by the cartridge PGBK. The lower half of the grid is blank. I've flushed it under hot water for a while, but only the colours came back to normal pattern. Any suggestions, please?
Unfortunately a 50% of the nozzle check blank on any channel means an permanent electronic failure. New print head will solve the problem unless your logic board caused the electronic failure to begin with.
Thank you for the prompt answer. In your experience, do you reckon that a new print head could have a reasonnable/affordable cost? Or it's not worth it?
Hi Jose, I'm loving and learning from your series of video blogs which include information I've never read before. In this video you mention that Canon printers should not be turned off because they have an internal clock to keep inks agitated and nozzles clear. You listed the printers involved from the Pro 9500 onwards. I have the Pro 9000 would you know if this printer has the same internal clock system? Thanks in advance. Andy.
The inks are not kept agitated. Basically its a timer that will trigger a cleaning cycle if you do not use the printer for 60 or more hours and yes, it also affect true PRO-9000.
Hello, thank you for your info on Cannon printers. I let my cartridges run empty, or at least I thought. The black cartridge still printed but not thoroughly. I purchased new black and color cartridges. Now, although the printer prints as I test printed pages, cleaned thoroughly from printer panel, the ink cartridge supply ink levels keeps reading "information not available". Can you kindly send m e link or info on how to remedy problem. Thank you.
Jose Rodriguez hi thank you for your reply. It’s a cannon pixma 492. Cartridges purchased at staples and microcenter. I do not get any errors such as lights or messages. It simply does not pick up the ink level and when I click it to find out. It says “information not available” I took the cartridges out unplugged machine put them back in and still no show. That was the only suggestion I could get from cannon support page for that machine. Thank you
Not a model I am experienced or familiar with as I only work with Pro Photo printers but if the carts are not original Canon cartridges, that will be a possible cause for the non recognition of the ink levels. If the are original then something's mg is damaged with the internal contacts on the print head contacts or the communication with the printhead to the printer
Jose Rodriguez ok well thank you anyway. May they are cheap refills via staples and MicroCenter. I will call cannon soon. I do appreciate your time. Thank you very much for being helpful to us. Be well.
My pro 1 bit the dust after 5 months of use.canon has stopped making them so they are sending me a pro 10 I will have some extra replacement chip for sale soon
Hi Jose, I have a canon pro 100 because I saw your videos, but I cant print 4x6 always said paper jam......all other size is OK but 4x6 doesn't. Is there a trick that you can share > Thank you in advance
That should not be happening it should be able to print flawlessly in 4 x 6. You might want to run the roller cleaning utility in the driver is located in the maintenance tab
@@cheo1949 Thank you....you are awesome.....I want another tip for you, I have canon photo paper Plus Semi-gloss, what paper for best result like photo printed at walmart photo center (it's said FUJI FILM) but no idea I need print photo from church. -
I think you might mean www.patron.com/jtoolman That is for automatic donation from $1 and up. Otherwise there a SUPPORT bottom on the mid right area of my main channel page for single one time support donations. Often it is called A Tip Jar. Thanks!
You have so far. Can you tell me which of your videos shows how to turn of printer color management. I'm not sure if I've done it right and can't remember which of your videos shows it. Thanks!
Do you know how to reset the ink counter on the mx series to clear the end of life messages that you get when you hit 60,000 prints to reset it back to zero ? There was a program made by an Indian tech student that could service a lot of settings in the printers that were the L series It doesn't work for the newer MX models Any help is appreciated Thanks Bill
Do mean you want to reset the waste Ink counter?? You need the WIC reset tool plus a $10 serial key for the reset. Get it from www.ocotoinkjet.co.uk But if you mean something else then I need more details. Realize that just resetting to zero does not remove all the waste Ink out of the pads. Eventually they overflow.
Jose Rodriguez the counter needs to be reset to zero. Cannon sets it so when it reaches the number it stops working and says end of life even though nothing is wrong. I can clean or replace the pads I thought there was a way to clear the counter from the buttons on the top using a sequence to get to that hidden menu
Wait are you talking about Epson or Canon here. New canons quite often cannot enter service mode unless you have access to the can on server along with login credentials. If Epson look to see if the WIC reset tool will work. Otherwise there is not much more I can tell you.
Hi Jose, this is Hector. I have a Canon MG5720 Inkjet printer which I have not been able to use since new because the magente color would not print. I placed a tech report directly with Canon and they so kindly sent me a new headprinter in the mail. I replaced the headprinter and to my surprise nothing changed. I still have the same problem of the magenta color not being able to print. Somehow I am inclined to think that the printer has not registered within its local memory, I suppose, that it has a new printhead. If this makes sense, do you know a way to tell it that it now has a new headprinter ? or maybe you can tell me what other problem I may be facing. Thank you very much.
I have no idea as I only use PRO Photo printer. I know nothing about any of the MG models. Did you fully remove the vent tape on the magenta cart? If not ink will not flow and the printhead will burn out.
You need to run a nozzle check or a print through your printer every couple of days to prevent your printer from wasting ink on automatic cleaning cycles. Now you know everything from the video and skip the pain and suffering of watching it.
Sorry I put you through pain! You obviously are not used to the format of our videos here. It's more like a conversation and not a 1-2-3 of A-B-C impersonal do as I say in two minutes. If that is what you are looking for them I suggest you look.else.where.
Stumbled into your channel by chance. Just a question, isn't this ink printing outdated technology? Why not go with color laser printing which is hassle-free and isn't the resolution catching up? I think you could get size E and larger printers for some time. By the way my attention span is just a little under 9 minutes so I'd watched most of this video.
Thanks for watching by the way but....Outdated???? You are kidding right? LASER can not even come close to what you get from a 12 color Fine Art Photo printer. For documents and flyers, that do not require gallery level photo quality.... ok maybe! When I see laser printers than come even half way close to my quality then I might change my mind but that will never happen due to the simple totally different chemistry used by either technology. Those LASER Printed Photo albums and nooks you buy on line absolutely suck in comparison. I will put up with the inconvenience and babysitting you have to devote for the unbelievable quality you can get from a great inkjet photo printer. remember I am not talking about the junk you get a the local Staples Store.
the BJC-50, 70, 80, 85 etc also seem to do this I own a few of these and have opened them and cleaned inside including the pads used for this. I still dont know how to make these printers pick a sheet of paper from loaded stack after a few years, any help with this would be helpful. also how to replace the battery pack for models with that option to extend recharge times
I am not familiar with this family of printers. Just how old are these models? When the paper refuses to feed after a year or so of sue is due to the rubber rollers no longer being "Sticky" so they can no longer grab the sheets of paper consistently! Are these portable printers? I would assume their waste pads reach max load very quickly!
correct. the series was from about Win 3.0 through Win7 when Pixama came out as an upgrade. then mobile printers dropped out for some reason. the model numbers ran out of order also BJC-70, 50, 80, 55, 85, 90/pixima tru the 100s til Pixima was dropped then a few years til ink was dropped. I own several as I love the portable office ability with IBM laptops which I also have many
I remember seeing these on the old PC magazine. They problem was their internal ink pads maxing out very quickly! But they did seem very convenient at the time.
oh and the waste pads also disentigrate after long un serviced periods and seem unreplaceble without a whole part being changed but they are no longer supported so gotta tinker and DIY made parts from donors.
I have learned to get several of the tray cases that screw down air tight to store ink in between use and when traveling to save ink and printer problems. the battery pack has removable battery but havnt found replacement yet. likely costly also. I may try rebuilding it inside if I find a spare in case it gets damaged.
Hello Jose! I have a PIXMA Pro9000 Mark II. After replacing an 8M and an 8PC, my printer stopped printing and popped up a window with a B200 error message. I removed the print head from the printer (which, to my surprise, was very dirty) and held it under the faucet to clean it out. I rinsed that print head about five minutes before the water was clear. After the print head completely dry (I'll let it air dry overnight), what do I do now? I can't afford to take my printer to a repair shop right now. Can you help me? I certainly hope so.
Thank you, Jose. BTW, you said it could be something else. What else could it be? I would really hate to buy a print head (they're not cheap) and that's not the problem.
Actually that one is pretty cheap! Try $500!!! When you removed the head and did your washing, did you unplug the printer? The reason is the recommended thing to do is to power off, remove the plug for about 20 minutes and then re plug and power up. Besides a damaged printhead it could something as simple as a bad contact of the back plate of the printhead to the contacts of the printer. If after checking that and doing the power off and back on it does not work then your only option is the new print head.
"You are more right than wrong," as my late mother would say, when trapped for an answer, I watch your tutorials and listen to your advise, as I am considering a Pro printer when I can, but for the moment have an Epson XP-960 for which I sat there very frustrated in urgency to print and caught with a cleaning cycle, caught with likely over soaked pads, and more than two resets. So, what you say makes good sense and that when I can renew my printer for the 700 or 1000, I am now warned has been the source of my problems too. Thank you, I am learning and hope others realise you are correct and make saving on unnecessary ink loss that should realistically, be used instead on the next print.
Thank you. My printer has never printed in 2 years of owning it. Your directions were followed and miracle of miracle. It worked!!
WOW! Two Years? Could you please share with brand and model and what did you do to get it going again. Thanks!
Printer was a brand new Canon 3621 and for 2 years it did not work. I emailed Canon and they sent me new carts. Your video's instructions were straightforward; I followed them and voila!! it worked. Thank you again.
Sounds great!
My experience is this: I don't use my Pixma Pro 9000 for days on end. It is set to "automatic" mode. It supposedly goes off when not in use for a number of minutes. Not really "off" but it is "sleeping". It is sleeping until you command it to print something and it will print usually without doing a cleaning cycle. It will, however, initiate a cleaning cycle when it is just siting there for a few days without my intervention because it was just "sleeping" not "off".
Didn't you just contradict yourself?
":It is sleeping until you command it to print something and it will print usually without doing a cleaning cycle"
"It will, however, initiate a cleaning cycle when it is just siting there for a few days without my intervention because it was just "sleeping" not "off"
OR do you mean if you print something withing a certain number of hours while it is in SLEEP mode it will not do a cleaning cycle unless it sets SLEEPING for days?
I currently have all my CANON so they never sleep or auto off.
That plus using them often will pretty much stop most auto maintenance.
The PRO-9000 is ancient by comparison to the model I am talking about here.
I have two 9000MKII sitting on my floor right now. One new and one with no printhead.
The inks were low on my Pro 200 and I started to replace them as they ran out, I saved ink and got extra prints out of it but it restarts each time so I now put them all in at the same time to avoid it, I also print a 6x4 every week or two and the head has not blocked so far. Photgraphy and printing is an expensive hobby but thats just the way it is if you want the best results. The best way to print cheap is to use a printer like the Canon MG5750 with non OEM inks i get decent results for not much money and if the printer dies it's only £50.00 for a new one, Iv'e had mine for maybe four or five years and it still works well and it's never blocked up in that time, leaving them dormant for months on end is the worse thing you can do to a printer.
You are correct. I have a 15 year old Cannon printer and when new, I could go weeks without the inkjets drying up. Now it is like 24 hours and I have to do a clean cycle. Mine does not go into auto clean mode. I think it is the design of the cartage. Face it, they don't make much if anything on the printers. It's the ink cartage's that are the cash cow.
30 years ago I worked for a company that made Fax machines. They had special paper that they basically burned the image on. No ink at all. It should be easy to do black and white and grey tones easily. Color would be tricky.
Canon IP7260 here. I replaced all the cartridges with refillable cartridges and the ink cartridges have worked fine and are still working after two years. I am using non-genuine inks meant for Epson inkjets because I already had 700ml bottles of them from 7 years ago when I used Epson printers.
The colors look close enough for me--not accurate--but it doesn't look bad or wrong. Monitor is calibrated using EyeOne Match Pro, which is probably the most important step I have done. You can just keep manually adjusting the colors for your printer profile after each print until you are satisfied with the color-matching.
However the pigment black is no longer printing as I stopped printing for a month. Perhaps it dried up & clogged the heads. Cleaning the heads doesn't fix it.
My work around is to change Printer Settings to "High Resolution Paper" which will use normal black ink instead of pigment black.
Best thing to do is save up for a second hand Xerox Phaser color laser printer. Sometimes companies sell them really cheap or even give them away for free when they upgrade.
All I can tell you about the Black Channel is that's what happens when one doesn't print fro a long time and Compatible and refillables are awful for CANON Printers. Pigment will clog quickly when not used often.
I think you are the one "expert" that really knows what he (/they) are talking about. I have been using Canon printers for over thirty years and presently have an MG6620 I have always LOVE the Canon printers. I recently decided to replace the print head (QY6-0082). I ordered one and when I got it, it gave me the error "wrong print head". It was clearly marked "QY6-0082" but only when I put the original print head (a QY6-0082) back did everything work..
Is it that there are varieties of QY6-0082s, or can the Service Tool allow resetting the printer to allow the replacement head to work? OR is there a combination of button-pushes that will do it? [and where can I find a reliable source of the Service Tool???) Sincerely, Dr T Rowe
WARNING!
If you have short attention span problems do not watch this video.
A lot of information here for a specific group of printer users using CANON PRO-100-10-1 printers!
thank you really really much
Huh? LOL
I do not have that particular printer but I do appreciate you sharing your knowledge. In my opinion Canon should mention these default settings and incorporate the possibility to switch it off or even implement the possible to create your own printing schedule like you explained. To me this seems a really gray area, where the manufacturer profits from printers not being used regularly and then emptying cartridges by these programmed cleaning cycles..
They will NEVER do that. They want you to I've everything alone so you waste a lot of ink. Sad but true.
A quick story - I bought a 2nd hand pro 9000mkII on ebay . It was described NIB but when I got it , a few inks were done and the green channel was totally clogged.
This was due to it probably sitting in a box for 2-3 years. I assume it was given away with a Canon camera purchase.
So to clean the head I used NO solvent. But I did use an ultrasonic cleaner , hydrogen peroxide and a small amount of isopropal alcohol. half an hour in cleaner and testing it - the green now flows perfectly while on the test strip it was blank when printing green.. no lines or anything. Just make sure you take out the rubber if using alcohol.
Usually it's not recommended that you use an ultrasonic cleaner. It can actually cause internal damage of the internal delicate components. Also Hydrogen peroxide can cause damage. Most canon print heads need only need to be partly soaked in warm distilled water with maybe a bit of Windex mixed in. But you had success and one can not argue with success. Enjoy your 9000 MKII.
I've owned a Canon IP-100 for nearly 10 years. Best printer I have EVER owned! Although the "cleaning" cycles are annoying, the printer WORKS. Which is more than I can say for HP printers ( worst I have owned). Also own a Xerox Phaser MFP 6600. High maintenance ( not for the technologically handicapped), but with care, they work well. And no ink to ever dry out and clog print heads ( HP are you listening?)
They are not. HP has sort of dumped the photo printing side.
Thanks for your great videos, Jose. Maybe I shouldn't have the puppy. I have had many Canon printers and have enjoyed making my own prints over many years. Over that time, I have replaced many printheads due to clogging. I was about to throw the whole idea of home printing out the window (along with the most recent printer.). But ....I got a Canon iP8720 last summer. My wife and I did our snowbird thing over the winter and took our truck/camper down to Mexico on a 5 month trip. In an attempt to prevent the inevitable printhead clog, I removed the printhead and stored it in a tupperware container. I used tye-wraps to suspend the head off the bottom and poured in distilled water with a little Windex. Not sure - but I think the liquid was just touching the bottom of the printhead. So 6 MONTHS later, I flush the printhead and reinstall it - sure enough - it's clogged. After 2 days of flushing, purging, using an electric toothbrush and cursing, I got it working.
........ I guess I can rant too ............. anyway:
My question is this:
Is there any way that I can go to Mexico and come back to a working printer?
(Not going on the trip is not an option - otherwise I wouldn't have all the great photos.)
- We do not have anyone looking after the townhouse - nobody is here.
- Would it be risky and complicated to come up with a system for automatic printing every 2 days? (5 months = 75 prints)
- Is there any way I can remove and store the printhead so it will not clog?
I am sure other retired photographers are in this same situation - I look forward to your comments.
Thanks ....... Dave
re. Inkjet Plumber, the Mac auto print app. I realize that the way to go is probably keeping everything together and just have my old laptop print out a swatch every few days. So Inkjet plumber MAY do the trick. Right now though the app will not wake up my laptop to perform the print. I don't want to leave my laptop up and running for 5 months. But I have contacted the author of the app and hopefully this situation will be solved.
Thanks yet again, Jose, for the candid and honest information and letting us all learn from your experiences. I look forward to learning more from you in the future.
Thank you!
According to the manual for the Pro 10, each time an ink cartridge is replaced, the printer is supposed to automatically run a cleaning cycle on the next print...so even for the frequent user this appears to be unavoidable. I've yet to verify this myself - just picked up one a few weeks ago and just now had to change one out for the 1st time, guess I'll find out soon. I've been running by the "60 hour rule" thus far.
P.S. Thanks for your videos, several have been very helpful in getting me started!
Yes. One complete ( all 10 colors ) purge cycle every time you change one cart. Yes the 60 hour cycle is also part of the PRO-10. That is why I have two complete sets of carts. Once ONE cart reaches low, I exchange the complete set with reset and filled FULL ( 10 cart ) set. Once purge cycle is generated and I will will not be changing inks for quite a while. The single cart changing creates what we call " The Domino Effect " you are constantly changing carts and others that were near low.... will them BE low after the ink purge. The two set / change when one cart is low scheme, minimizes the generation of waste ink and preserves and extends the life of your Waste Ink pads. Ta change then reset the Printer will cost you more than half the printers original cost.
Jose Rodriguez Wow, interesting and good to know - thanks. With the talk of minimizing/avoiding cleaning cycles, it seems somewhat surprising that this part of it doesn't get nearly as much attention as printing frequency, etc.
For me, the first cartridge to run out was CO (not a surprise), which I just changed out. I have not printed since changing it, so the cleaning cycle has not been triggered yet. The low ink warning just came on for Gray, and PB is about 1/4 full. The color ones are around half at this point. MBK is near full. Sounds like I should go ahead and change out Gray as well before I print again - and what about PB? What would you recommend? Thanks!
Officially that is never discussed as it is expected that NONE of us would or should be refilling with 3rd party inks. CO will be used at 4x the frequency to other colors. Grays are used a lot as well when printing COLOR. That is the way it is able to print super smooth gradations. You are on the PRO-10 so I said to change over when you hit LOW. Well that was a mistake on my part. Your PGI-72 carts do not have a sponge nor do they have to be modified in any way. Just reset and drip ink on the exit port till full at 33 grams. I do however exchange a complete set when ANY one goes to the empty or near empty mark. I remove them all and replace with 10 reset and full carts and continue printing. Then at my leisure I reset and top off all the carts I removed. One Purge per MAJOR cart change. No domino effect. SO you will need one more set of carts. Otherwise you will have to do each one at a time. Not good!!!
Ah I should have clarified - I'm not refilling my own cartridges (and don't have the equipment nor the space to do so even if I wanted)...just buying them the old-fashioned way - direct from Canon.
I have an extra set of all inks plus 3 COs. Ordered a Gray and a PB last night. Would like to maximize ink usage and minimize cleaning cycles so trying to figure out when it's best to switch tanks.
You have no choice as you will be changing them one by one as they reach empty. The "tricks" that I speak of are only applicable for refillers.
I use my Pro-10 a lot (several photo prints a week) so the few times I'm away and the printer goes into a cleaning cycle I consider it a good thing. I just love the photo prints produced on the Pro-10. (If you use Precision Color Inks the cleaning cost is negligible. Other than for photos I have very little need to print in colour. My networked Brother (black only) laser printer has been a real trooper over the years.
The only negative about these printers even using them with 3rd party inks is that eventually they stop working due to full waste ink pads.
And there isn't an inexpensive solution to this?
Solution to what. The Pads? Nope it requires a complete tear down and cost about $300 to do.
Wow. That is a big deal. How much printing does it take to reach this point? And do you know if there is a "meter" buried somewhere in the drive/software that keeps track of how much ink is used?
It's not how many prints it takes but how may For a ing cycles and I'm purges generated after EACH cart change. That ink is directed to the pads at the very base of the printer body. Totally inaccessible to you. The firmware keeps track and when a certain arbitrary Magic Number is reached, thats it. The printer stops working. It's not just the pro-100 but ALL printers with internal waste ink pads. There are tools for resetting most Epson printers but not Canon, but the ink is still being accumulated in the pads and eventually you overflow.
Thanks, Jose, I appreciate your response. I will get another one and not worry about it.
Good luck!!
Your videos that I have seen are very informative and useful. This one made me realize that a printer at home for say 13 x 19 prints just would not get used enough to justify the costs of ink. You mentioned Qimage, which I have supported for over 10 years (for when I need to do a print) and I know ice profiles for the printer at COSTCO near me can be downloaded. Could you do a video step by step workflow for exactly what needs doing to get the best results? That would really help me.
Are you talking about you printing at home or prepping for COSTCO to print for you? If so they would be using the paper profile and not you. You would process as prep you images as you normally would. No special secrets that I know of.
You sir, are the man. Thank you for your time and knowledge. Much appreciated
Thank you Freddie!
I own a Canon i960 inkjet printer (ca. 2004). I don't print everyday and usually it goes like this...
I "re-discover" my printer and start using it for a few weeks. Then months or even years go by and I ignore it.
Still have this printer and it works flawlessly, as long as I use the 3rd party Linux driver TurboPrint for it. I get 1200 dpi (fine mode) under TurboPrint, where I only ever got 600 dpi from the CUPS-Gutenprint driver.
My housemate friend on the other hand bought his Canon i960 in 2007 and must have used it constantly. He tells me that the printhead wore out and the printer is no longer usable.
Sure it does the nozzle check and must have wasted some amount of ink since 2004 and perhaps I've had to purchase more ink more frequently than otherwise. But if I don't print that often anyways, to me, it doesn't really matter. I don't wanna hafta search for some image or document to print to keep the it from doing the nozzle cleaning.
I love the look of my i960 and the fact that it just does printing. Not scanning as I have a Canon LiDE 110 for that. No use for fax but I do have three places I could go if I need to fax something.
SO what you have discovered is simply this: Older CANONs are built so much better and perform so much better than our newer models. It is sad but true. Since you print so sporadically as you say only after you rediscover your printer, it is not using any ink during all that time so even with a cleaning cycle it still is not wasting a lot. But my current advice is for folks who are photographers and print much more often than you but sometimes not within that 60 hour limit. They will pay for that with a cleaning cycle. Now about the print heads. Canon print heads are thermal and basically are self destructing themselves as they print. But a print head for a PRO-100 is only about $70 so who cares!! Plus they are user replaceable!
Well that explains a few things. I have hardly used my Canon printer at all, and it's already telling me "low ink".And all the "cycling" it does whenever I turn it on. It's a 3600 series, and for what I use it for, I spent too much.
They do want to be used often so the ink is actually used for printing and not for generating waste ink.
I learned from your experiences and I haven't bought the printer yet. :)
PRinters are so cheap these days , and carts readily available. But it's become a throwaway society, As I remember 10 - 15 years ago - people buying printers second hand just for the cartridges because they were now an obsolete and the quality was so good.
Dear Jose, I have enjoyed watching your videos and learned a lot from them. I had a Pixma Pro-9500 which worked fine for around 5-6 years (I can't remember exactly how long) I did not use it that much because of the cost of each cartridge and I now realise that this was false economy. Eventually the print head clogged and I could not unclog it so I replaced the 9500 with the Canon Pixma Pro-100s. After watching your videos (which all seem to have referenced the Pro-100 and not the 100s) I thought I knew how to do things right. I keep the printer on all the time and I make a print every two days. Sadly, the 100s seems to keep carrying out cleaning cycles, even today when I made two batches of prints it seemed to carry out a cleaning cycle before each session. Do you think that Canon have heard about your videos and changed the firmware so that the 100s is scheduled to do more cleaning cycles and not just after every 2.6 days?
If you hear a whirling sound it is simply emptying the purge pad of any ink that may have collected during the previous and current print jobs.
That's a relief, I'm always good for the odd conspiracy theory!
This video was fantastically informative and really hits home ethical printing. It felt like therapy. I'm Christopher and I'm a printaholic 😔.
Thank you! Most people HATE this particular video. Apparently it's too long I don't get to the point in one minute. So I really appreciate do that you like it.
This is true of non photo grade canon inkjets as well. You really have to run a print with them every other day or the printer will go through a cleaning cycle and you will waste a lot of ink. I just use the inkjet as the primary printer with one of the computers I use every day. The lazer is faster and less expensive to use but you have to exercise the inkjets to keep them happy.
If you do not print medium to high quality photos there is no reason to own an inkjet printer. Laser is always the best choice!
I use my inkjet to print graphs 90% of the time because the color makes it easy to differentiate between the plots. Also most people own inkjets just for printing documents but some do let their priter sit fallow for a week at a time and then complain about excessive cleaning cycles and high ink usage.
Well using an inkjet for just documents just doesn't make any sense! Unless you use it daily. One of the reasons is printers of that lower caliber are practically being given for almost free and the cost of inks hits you. Their response is...What, you didn't know??
On other hand if I have a high end inkjet that I use to create prints for sale and it cost a total of say $20 including paper and waste ink generated but I sell it for $100, then that makes sense to own that type printer. Using it for printing emails or web pages.... No way!
People need to look at the situation that way.
Inkjet technology is finicky as hell.
When I worked wit drafting pens the various diameter would constantly clog and practically lived in the ultrasound bath.
My fault for letting them dry from lack of use. Same thing applies to inkjets.
Never had that problem with a brother printer. I use it once a month and had no problems for over 10 years.
That's all it takes. Some printers are more finicky than others.
I had a canon printer that went thru the mentioned 2.5 minute cleaning cycle every time I wanted to use it. Threw it out the 2nd story window. Life is now good.
That's what happens when you don't use your printer often. Get a laser printer and send you photos out for printing.
Actually, I was using it quite frequently. Bought it new and it wasn't cheap. After a few months, it would error after the clean cycle and recommend yet another clean cycle. No matter what I did, it never resolved itself. That was more than 15 years ago. After all these years, hearing people are still dealing with annoyingly long clean cycle on Canon printers, makes me feel glad I thru it out the window and never bought another canon printer since. I've owned other brand inkjet printers since, they are fine, even after long periods of non-use.
And just a few days ago some one said that these claims were a total myth! What model did you have? Was it an AIO of a photo printer?
It was a long long time ago. Late 90's Model was something like BJC-3000. I was highly disappointed that issues like this still exist with this brand today. Glad to have steered clear of this brand printer ever since.
DIY: get epson, gut it till it still works, buy a kit that lets you connect print head to large bottles of ink via thin tubes, and well have it gutted so you can manually clean the head if it gets too clogged. That's how i printed commercials/flyers etc for years.
And you can feed it cheapest ink you can find on the Fleabay.
I even printed with food colour dissolved in filtered rainwater (too cheap to buy distilled - i need enormous supply of demineralised water for my aging offgrid forklift lead acid battery ;-) and some generic window cleaner to lower surface tension (the one that had least pungent taste, no ammonia, which i thought has least corrosive stuff in it - questionable technique, but i don't have a gas chromatograph / mass spectrometer...for now;-)
The food colour bleaches in weeks/months, but who cares for flyers that will be outdated in few days...
Not nearly, but he's my idol ;-)
WOW you are a true MacGyver!
Pyroslav x: I don't know if you have a UA-cam channel, but you should! Sharing your experience offgrid and with printer, food colour stuff would be awsome!! AND you might make some little money as well.
Have a nice day dude.
I use my MP630 every few WEEKS. After a clean the cartridges are nearly empty. If I renew ALL the cartridges, print a few pages and don't use it again for a few weeks then the next time I use it it will purge and half the cartridges are empty again. I would say I get about 10-15 pages per COMPLETE SET OF CARTRIDGES. That's CMYB+large B !!!!!
Yes sure! That is what happens when you only print every few weeks. Cleaning cycles that initiated due to long periods of non use will empty tiny carts quite readily. That is what happens.
Hey Jose, I'm new around here but your channel is great. Question: You made a correction in the video info saying that the canon pro100 will do a time cleaning if you print or not, but then say that you should print every two days instead of let it do the cycle. So that confused me a little. If I print every two days will it stop the cleaning cycle after 120 hours or not? I don't want to waste ink. Thanks.
I have a pro100s by the way.
The pro 100 has timed cleaning cycles that will occur on your next print job after you exceed 120 or 480 from your LAST CLEANING CYCLE! SO if you print right this minute and you had not printer within the last 120 hours that print job would be preceded by a cleaning cycle because you had not printed within the last 120 or MORE hours. If you print anything within that 120 hour window no cleaning cycles will occur until you pass 120 hours. If you have not printed for 120 hours the cleaning will be medium and if you have not printed for 480 hours the cleaning will be larger. How much ink do they use? No body knows.
It sounds like you are new here so I would suggest you search my Playlists for TONS of PRO-100 and related info. Here is a video where I cover the subject you are asking about.
ua-cam.com/users/edit?o=U&video_id=LlZQj1uGqq4
I was wondering about your opinion on something. I have an IPF 6300 and I am now experiencing issues with my second set of printheads. I don't print enough and I have not been good at running nozzle checks and test prints to keep the nozzles from clogging up. At the present, I have ink in the machine and two, unopened printheads. I am talking to a retailer about getting some cash back for the print heads and putting that towards a newer, smaller printer such as the Canon Pro 1000 or the Epson P800. The alternative would be to keep the 6300 and use the new printheads. My goal is to have a more trouble free printing experience based upon low volume usage. What do you think?
The P800 would be your best choice for not often printing! But you must know how I feel about that! If I am not committed to use my printers at least once a week of more often, then maybe I should.not own one. But that is just me. The P800 will be more forgiving. But not the Canon printers.
I realize that regardless of how I go forward, that if own an inkjet that I will have to commit to a routine of maintenance prints to keep the printheads from clogging. It is interesting to me with the amazing level of technology in these machines that there isn’t a more effective system of self cleaning built in to these machines.
There is. It's called Auto Cleaning Cycles and CANON utilizes it. How are you going to keep tubules that are only 1 micron in ID clear of something that is not only fairly viscous but also containing solid nanometer size pigment particles in suspension. The only way it to forcibly suck out ink with the purge pad pump.
Thanks so much for the useful videos! I just bought the Pixma Pro 100 and they have been a big help. Question, in the short term, is simply printing a nozzle check sheet every 50 hrs enough to keep the cleaning cycles at bay?
Yes. Any print job. You want to break the idle period before 60 hours. So anything you print will break that will Interrupt the period of that idleness will do the job.
I don’t understand. You say 60 hour window to print and also 100 and 480 hour windows in one comment. Which one is it for the pro 100?
The PRO100 will trigger a pre print cleaning cycle after 120 hour of not printing. If you go past 480 hours it will run a larger cleaning cycle before it begins to print said job. Then the timer resets to zero and youncan print without cleaning cycles fornthe next 119:59:59 hours before the next cleaning cycles is added before the next print.
I had that problem with inkjet printers from many different brands because I only print something once every few months... Leave them on, and they clean themselves until they run out of ink, and they're out of ink when you go to print something. But leave them off and the ink dries out and clogs. But don't call me cheap because I can't be bothered to print a blank page every two days to keep the ink jet clean. That's a ridiculous thing to tell people! My solution is that I bought a color laser printer. A laser printer doesn't have this problem. A laser printer can sit idle for _months_ between prints without a problem. If your problem is you don't print often enough and your inkjet clogs or runs itself out of ink cleaning itself, get a laser printer...
And I agree with you 99% except for one thing. We are talking about Photo Printing Printers capable of high quality art prints. which lasers simply can not produce.
If you do graphics, text, brochures, graphics and even photo album pages then yes get a good Color Laser and don't even consider an inkjet printer. Id your be totally nuts to buy a 12 color inkjet printer meant for the production of collector level prints unless that is what you will be using it for. For everything an inkjet printer is not your best choice.
Not all brands or models do that. HP and Canon are famous for wasting your ink. I have an Epson XP-610 and use it rarely, I have never seen it go through a cleaning cycle before printing.
Wish I knew this before! This cleaning has been going on for hours😔
Inkjet costs too much per page anyway.
Yes,it is a tradeoff in machine purchase price and cost per page.
10 cents per page inkjet vs 2 cents for laser.
Photo print quality,the price goes up for either method,but inkjet is ridiculous.
Agreed. And that is why I only Print Photos with my inkjet printers. Document printing on them is out of the question.
The comment above about waste cartridges is untrue. Before your waste cartridge runs out of capacity turn off the printer and take out the waste ink cartridge. Go somewhere where there is water and you can make a mess, take out the screws on the waste tank, open it and remove and discard the absorbent material. This can get messy so have your trash can right next to you and wear your painting clothes. Once the padding is removed, fill the waste cartridge back up withpaper towels or similar absorbent material. Big box stores sell a heavy duty paper towel for working on cars and similar things for about $2 and it works well. Close the cartridge up, put it back in your machine. Go to service mode by pressing load and navigate while powering up the printer. Once in service mode, go to the adjustment menu, then to initialize and down arrow until you get to W_Ink (waste ink). Hit the OK button. Power down your printer. When you reboot your printer, the Maintenance cartridge will be reset at 100%.
Have you actually taken a look at the PRO-1000 waste ink.cart???
It is a sealed unit with no screws as you suggest. And even If you could.do that, would you reset the chip???? Huh??
You can indeed do that with the Epson large format printer's waste ink.carts but absolutely Not with the Canon PRO-1000 and up! unless you know something I am not aware of!
Good Lord, just pay the $15 and spare yourself of the mess of repacking a waste cart. Like I said I do it on the PRO-3800/3880 and P800!
I just 're dead your comment as you might receding to.other Canon printers with internal.pads. Are you suggesting a regular person to.do the pad replacement?
Then process you suggest works with older printers but not the newer ones. Firmware updates no longer allow you to.enter service mode unless you then log into the Canon service server and have a unique password.and key. As you an authorized service tech???
It works with my IPF 6300 and other IPF printers, which do allow you to enter service mode. I can't imagine waste all this ink with cleanings and having to purchase waste ink cartridges too, sounds even worse than the IPF printers.
Yes you indeed can do what you propose on those older printers but such is not the case with the new line of IPF PRO models from the 1000-2000-4000-6000 The Carts are hermetically sealed and Totally seamless in construction. The only entrance is the waste inlet port and there is s mall rectangular felt pad that allows you to see when it reaches saturation. It is a 100% throwaway product. And no you can not enter service mode as I said on these newer printers.
Great videos just purchased a pro 1000 you videos are priceless
Very good! Treat that lady with respect and love as she is a high maintenance gal!
Hello, are there any printers you’d recommend that are prosumer and don’t need to be ran weekly? Thank you!
Hello, I have a canon MX922. I have tried everything from cleaning the printhead, resetting the printer, adding new ink, even putting paper in the upper paper holder. What is the deal with these? I see this was a problem way back in 2017. What will solve the issue? Its grabbing the paper, acts like its printing, sounds like its printing and the page comes out white.....
Hi Jose , I've seen a few of your vids, more specifically around the canon pro 100 and they are very informative. I decided to purchase one today as I'm trying to turn my hobby into something more. While that happens I'm rediscovering printing having been out of the game for 12 yr-ish. I plan to use the printer but I wouldn't be surprised if I don't print every 2 days...I'm throwing this question out there to you as you have a handle on the ins and outs of printing. If you know you're not going to make that 60 hr window, and know that say you maybe will not print for 2 wks or more....could you remove the ink carts and store them so they would not dry out? Then slap em back into the printer when the need arises? Thanks again for your vids, keep em coming!
Mark
Sure but the internal timer will run a cleaning cycle p!us the fact that removed and reinstalled the carts will force a large Ink purge. There is no way to avoid the inevitable. You just have to print semething. Anything will do including a simple nozzle check.
Helped me out in a jam, thank you, my printer is printing again!
That great! Please share with us what the problem was!
It's not just the pro printers that do this - even the cheapest consumer printers run autonomous cleaning cycles. A print a day keeps the ink waste away..
Indeed.
Hi Jose and congratulations for the excellent work.
I print black and white 99% of the time (with the option print in b&w selected from the printer's software) and I wonder if I use all my inks, or just the monochrome ones, Basically I need to know if I still have to run nozzle checks within the 60 hours window, even if I print b&w prints in intervals shorter than 60 hours.
Thank you in advance for your answer and best wishes for a healthy and happy 2017!
I can't say for sure whether printing in B&W mode uses only black and grey inks or a composite of all colors. I think not. B&W seems to basically just do an on the fly file conversion to B&W at the driver level. To try to answer your question concerning printing within the 60 minimal.period. Anythng you print will count. However there are reports of other types of noises occurring before a job begins to print even under the 60 hour period. Its hard to determine what the printers are actually doing.
thanks for the information, clearly canon printers are not the brand to buy, thanks again.
Actually they are outstanding. Once you know how to use them properly.
Jose, is there any reason my Canon pro 10 can not print a 13 x 38 inch pano print? When I set it up the paper size and print, but it places the image going the wrong direction. I changed the orientation, but it still prints only a horizontal strip of the pano image. What can I do?
I confess to being confused. I wish you had pointed the camera at the printer just once. Are there really $1000 Canon printers? What does it do to be worth that? I bought a Canon Pixma 3600 series printer at Walmart for $40 and I have printed documents in color and black and white and even 8.5" x 11" photos on photo paper and they look great. It also scans and I have digitized hundreds of family photos into my computer. Never once has it done anything on its own or run a cleaning cycle. I'll admit the cartridges are a bit pricey ($60 for one of each) but I haven't kept close track so I could break it down by page. So, why $1000 printers?
Those $60 Canon Printers are only letter size paper capacity and so that limits it as far as creating LARGE prints which is what you pay the extra bucks for. Unless you use third party inks the inks would cost you 2x the price of the printer and that is why they are priced so cheap. The PRO level CANON Printers we are working with will range from $400 to Thousands of $$$. The technology is many fold more advanced and is meant for truly professional production work. The one next to me is the PRO-1000 and it retailed for $1300.
Jose, love your videos and just purchased a Pixma Pro-100 printer. Can you share the details on the "un-clog tool" and scheduling software that you discussed in this video? Much thanks!
I have videos on just that in my QIMAGE Playlist!
Thank you Jose!
You are welcome!
I am surprisedat the number of users here that don't seem to understand that when you talk injets vs. laser it's apples and oranges. For high quality photos you need ink jet, for documents you don't.
So true! If a laser could produce Photo Prints on Baryta Rag paper I would switch instantly but.... they can't!
Thanks very much, but I just ordered a Canon TR7520. Would this be the same routine for this series of printers? If not, what can you offer for keeping it from clogging when I get and start using it? I think I have found a good ink supplier that gets their ink from a US manufacturer and is supposed to be formulated to the same specs as OEM much less expensive. Ink Owl is who I am considering for the ink. Any advice for me? Thanks. I enjoy and have seen some of your videos before and they are very good. I can tell you really love your printing.
Yes the routine would be the same. But the times cycles would be different and No one knows what those are. Ink Owl inks are made by Image Specialists who was bought by a Florida based company. And no. No 3rd party inks dye or pigment match oem 100%.
Thanks much Jose. So I should avoid ANY 3rd party inks then, right?
I didn't say that. You want to save a lot of money? And don't mind losing a bit of quality but still want to the print? Then by all means. A good paper printer and ink profile will get you as close as possible but not exactly. So you can't have your cake and eat it too.
That'll work for me. I am not an aficionado and probly didnt even buy the best printer for my needs. I will be using it to print flyers for my business now and then and mostly text documents. I was gonna get a Canon Maxify but I think that one will only use pigments which I dont need. I really wont be printing alot of pictures. Just once in a while. I had an Epson Workforce which was a nightmare after one year. I had one previous to that one and same thing. So i thought I would try Canon. I purchased 3 refurbished Brother Laser 9130CWs for my business. Every one of the Brother 9130CWs would leave toner smudges every few pages and would also come off on my hands. I had to return them all. That would have been my printer of choice for my needs. Was very disappointed. So I'm back to trying an inkjet again with Canon which I never owned before. Thanks again. You are a great resource and I subscribed.
Hi there nice review, so what do you make of Epson Eco Tank printers. Would you recommend that for some one serious about photography And want to print photos. Many thanks.
If you want to pint photos then you need to get a Photo printer and not an Eco not l. They use cheap low longevity dye inks. These Pinter as for quick document printing on plain paper such as you would need in an office situation and you need some quick flyers. Don't believe the claims from Epson.
Ok. I just cleaned my pads myself, for free. My hands are dirty now but if i wore nitro gloves they would not be.
so now I got this. I just need to print something, even a check heads test sheet every day or two and I will be all good. Oh yes, and I do not need a puppy. I don't pay squat for ink, this is why I love my cannon.
How did you reset the ink counters? Were you able to enter service mode?
I have some directions here that I got off line but they do not seem to work, what I ended up doing was by passing the error by just clicking OK. it did come up again and I did the same thing I just pushed OK on the printer. The error code went away and the printer continues, i guess it may do that every time I shut it down and power it back up. it is working though so no biggie I guess. The instructions I got were like the damned Hokey pokey dance, they didn't do anything it seems but waste my time. i will keep looking though, if for nothing else but to save the extra clicks LOL Oh! those pads were easy to clean up, I used a little dawn detergent and hot water from the tap, I kept ringing them till the water ran clear and then I flattened them out in paper towels and set them on a rack in my oven on proof. which is 100 degrees worked great. the inks light right now, I took the head out and cleaned it the same way , I think it will get darker after a few prints go through.
i was looking on eBay while my pads were drying and I saw print heads from China for that use ONLY BLACK, I wrote to ask how they work, that would be a huge money saver for me.
I have a Red resetter. I got the cheap one and hacked into it so I could re power it . it works great.
Hi, Jose.
I've heard you often speak about the timed Canon cleaning cycles, 60 h, 120h, 480h. You say that if one prints before the timed cycle "your ink will go to the print and not be wasted on a cleaning cycle." I'm confused by that statement.
Do the cleaning cycles occur even if you are printing every day, or does printing "reset" that cleaning cycle clock so that it does not occur until the printer is idle for the 60, 120, 480 hrs? Thanks
Okay. We now know that printing those not disable any of the cleaning cycles that occur. Pigment printers like a pro 10 will run a cleaning cycle every 60 hours whether you print or not. The pro 100 being a dye ink printer has a longer. 120 hours again, whether you print or not. Please go to my video list and look at the very recent one that I did a few weeks ago it explains everything We now know about the maintenance Cycles at the Canon printers run.
@@cheo1949 Aha, found it, thanks
Dear sir. I have the pro 10, and expecting to receive a pro 100 soon. They are such a good value to be passed by. Just a casual check. Do you think the chassis of the pro 100 is the same as the pro 10? You think if a pro 10 print head is inserted into the pro 100 chassis .. and perhaps unlocked it's use as a pro 10? They are so similar that it seemed plausible that Canon could be manufacturing the mechanical parts as the same design, whilst having a different firmware for each model will bring down their manufacturing costs. If this hypothesis is true. We may just have a cheap chassis for replacement in case the ink pad (irreplaceable) becomes saturated.
I'm pretty sure that will not work. Both printers PRI t head carriages are different and so are the heads. The chassis is internally also different as is the motherboard and firmware.
Jose, could you answer this for me? I want a large scale printer (13x19) to print on 140lb watercolour paper, pretty much only in brown ink (the line art must be waterproof) and the printer would be sitting not used much of the time. I could buy a used epson r2880 (found one used for 250, but how old is it?l and might sell today) or a new Canon Pro 100 ($400 by payment plan)....could you advise what printer I should buy and things I should take into account? The essentials: waterproof ink, large scale that takes heavy art paper and will sit not used, but I could only use brown line art ink. Under $600 has to be, can't afford more
I don't know of any Brown ink for any of the common printers. You would have to custom mix ink compatible to EPSON photo printers and load cartridges with it! So for instance with the R2880 you would need 8 refillable Carts loaded with this custom ink. Theoretically should work.
I like canon printers, but i am away for long periods from home like a month or two. What do you suggest me to do about my ink cartridges? Should i move into a laser one?
You carts will not suffer at all. But the print head could show clogging. Dye inks will clog less than pigment.
So do i need to leave my printer on and plugged in? I have a Pro-100 which I do my best to use every few days, but every time im done printing I turn it off (still plugged in, just pressing the power button). I've noticed that when go back to turn it on and print the printer will make some noises for around 30 seconds. Is this the cleaning cycle you are mentioning?
Yes. On 24/7. You can prevent the cleaning circles that take place whenever you repower on the printer. But you cannot get rid of the cleaning cycle take place for normal maintenance but at least you can reduce or eliminate the ones that would occur when you re power on so leave it on 24/7
Buy Brother. They dont use "smart cartridges" that commit suicide, yet. Simple mechanical reset wheels.
If I was talking about office Printers then maybe but I am not. I am talking about dedicated pro level photo printers and not document types. If you print non photo document then a simple cheap laser will fit your needs better. I am talking about a totally different class of printer here.
hi, i have an old (circa 1990) Canon Bjc-250 printer, very good, that worked very well for me and uses Windows XP. The printer worked well until 2017, when, one day it stopped printing altogether...when i send the command "print" (in black and white, that is all I do...)there is total silence. Before this , at the clicking on the "print' word, there used to be an immediate whirring sound and the pages would start being printed quickly. when the problem started i bought a new b&W cartridge,installed it, and again clicked on "print", but there is a total silence, nothing happens.....could the cause be that microsoft stopped supporting the WINDOWS XP around 2014/15, and then this cause my BjC-250 stopped working forever?
Nope it died of old age.
Thanks for the awesome video. Just purchased my first Canon printer, an MX922. Looking forward to long life. Just curious, did you ever find a way to trigger a nozzle check from a PC?
You can trigger a PURGE print but you need a script which I do not know anything about. But Qimage Ultimate, the print layout tool will allow you to PRI ta scheduled color Purge print on schedule.
Jose Rodriguez Awesome. I'll look into that. Thanks. 🙂
Coool... Thanks for sharing your experience. As an aside... Google is awesome!!!! Without Google, I never would have saw your wonderful videos.... In either case, thanks again and I am going to eventually get a Canon printer, but I am wondering what sort of upgrades would be in store for the second version of the Canon 1000. Will they make a second version that would still be desktop, but can print 24 inches? Will they address or present an alternative method to their anti-clogging feature? It will be interesting. I am actually thinking about just holding off to pay full price for whatever the second version of the Canon Pro 1000 may be. In either case, have a nice day.
I don't really anything of a desktop 24" model. The PRO 2000 already covers those features except for being a floor unit. This one uses roll and cut sheets. The PRO 1000 still has a length limitation.
Thanks for your kind and prompt response. I actually just received my Canon quote yesterday for the Pro 2000. But the more that I thought about it, I love the concept of the desktop more so I decided to pass on the Pro 2000. Maybe I can upgrade to that one later if I never get what I want in the desktop version. I just wished the Pro 1000 could print 24 inches. I am not too concerned about length as I am primarily printing portraits and likely some landscapes.
I just figured that by the time that I have the money for the Pro 1000, maybe they will have a second version of it out. I was curious on what that new version would be. Could it be 24 inches in a desktop environment? I know some may say that they would not risk galvanizing their Pro 2000, but a I just truly see the products as different. Ooooooor could it be something truly awesome such as larger ink carts going from 80 mL to 137 or 200 mL which I believe are in the larger models.
Pay me no mine... I was just brainstorming what the ideal next version of the 1000 would be. It seems that a number of big companies have gotten in the habit of upgrading their products about 18 months to 24 months. Which means... That is too far away since the Canon 1000 was released. By that time, I will be ready to buy.
In either case, thanks for your kind response. Talk to you soon....
You can buy the pads on ebay and replace them yourself. there is no magic key to open these printers and the pads are user replaceable if you learn how to do it.
Sure! Easy for you to say! If it was that easy everyone would do it.
Also the new Canon models require you to log into the Canon Service Server and also have the service tool. Do you have the password and serial key for the server??? I don't think so!
Hey Jose, so if I turn my pro-100 off after printing is that worse then leaving it idle? Or is it just unplugging that's worse? I've been unplugging my printer every time I use it as I needed the socket :(
No need to ever do that. Unplugging will waste more ink when you decide to printer next time. The idea of turning off printer is antiquated and no longer relevant with today's modern printers.
Hola Jose, no se si me podras entender pero de igual manera te pregunto. He visto varios de tus videos pero no he encontrado la solucion a mi problema pero me han servido de mucho. Tengo una pixma pro 10 y cuando imprimo en papel tamano 4x6 al final de la impresion la foto queda descuadrada. Justo antes de terminar de imprimir la impresora como que hace un salto y la impresion se descuadra. Me gustaria mostrarte las fotos de como queda. Porque pasara eso ? es posible que sea el papel ? Tengo fotos de las fotos por si te gustaria mirarlas. Saludos
Estas usando paper brilloso? Canon, o otra marca? Creo que los rolos de transporte estan resbalando. Corre el proceso para limpiar el.Paper Transport que we encuentra en el Maintenance Tab.
Jose, te agradezco muchisimo que me hayas contestado. Si, es papel brilloso, es otra marca y ese papel tenia muchisimo tiempo guardado y como justo compre la impresora lo use. Cuando imprimo en papel brilloso tamano carta si imprime queda perfecta la impresion. Es posible que sea el papel ? Como se corre el proceso ?
Aca te dejo el link de como quedan las imagenes. Solo sucede con papel 4x6.
wetransfer.com/downloads/3aa62a0e899ef19565f75278d57deb2b20180828195903/8c68313db33f131a61569ee7e5ee44ea20180828195903/0b75ce
Si no es CANON puede que sea demaciado resbaloso i al final se muve o se mueve. En el Driver se va a "Maintenance / Roller Cleaning" i siga las direcciones. Si eso no lo arregla el problemba tendras que usar otro tipo de papel. Que Marca es?
La marca es 'image plus' eso lo compre hace como 6 anos minimo. Creo que si es el papel. Tengo que probar con otro y te aviso. Gracias de verdad
I have an older Canon MG8220 Photo printer that has 9600 x 2400 dpi but only prints out a 8 1/2 x 11" borderless max.
It prints out beautiful pictures, so my question is about the Canon Pro 10. Would it print out pictures that would be considerably better?
By the way, I can clean it through the maintenance program, all done manually. It can sit for months and no problems with clogging.
The front right side paper tray was broken by someone but it can still be positioned to work.
The PRO10 is of course a superior printer dedicated to printing photos. Unlikenan AIO type. It will print on any type of paper.and canvas up to 13x19
Will you need a huge difference? Not in most cases.
@@cheo1949
Thanks, I'm currently looking at the Canon Pro 10, and 1000 printer.
If you are just getting into this I would forget about the PRO-1000. That is a production printer requiring daily use with lots of large prints or you will use more ink on maintenance cycles than on producing prints.
Thanks for taking your time to share your advice. I was leaning towards the 10.
Does the 10 require a lot of usage also or will it also perform maintenance cycles after 60 hours of non usage? You may have stated that in the video and if so I apologize for not remembering.
Thank goodness for affordable laser printers! Life got so much better when we threw out our HP ink jet printer. Never could figure out if HP's protectionist ink policy was more akin to armed robbery or extortion.
So what are you using now? A Laser I hope. If you are printing only documents then inkjet is not the way to go.
Jose Rodriguez We were slow to realize laser printers had plummeted in price. What little color printing we absolutely must do, we do through local printing and photo services. Grayscale pinch-hits for everything else. Brother is the brand we went with. Figured we'd feathered the nests of enough HP executives. Very happy so far.
Dear Jose, just discovered your video channel. It's clear to see you are an expert on printer problems. However l suspect many people just want to print off occasional bill receipts and photos et, not professional quality
That is why I do not deal with document type All In One printers. This channel IS about Photo Printing and photo printing and NOT about once a month printing of a bill or envelope.
Jose: Just got the Brother Mfc-J5830dw. The inks are claimed to be archival by Brother. As expected, they say you need to use their paper. Does the type of paper you use effect the archival quality of the ink? I intend to use QEM ink only as I will sell 11x14 pics. Thanks Charlie
Yes Paper is just as important as the inks themselves. But you know that printer only uses four colors and if by prints you mean Photos, that is not going to work very well as far as color fidelity of your prints. The gamut will be quite low even with OEM inks.
My Pro 9000 mark2 eats ink, it seems to run a cleaning cycle every time it is turned on, even once a day
Of course. You are not supposed to turn it off and on. That is what it is programed to do. Leave it ono and print every other day and the ink will be used for the creation of prints.
Is they a flashlight looking. Spring in with the scanner arm if so where does it go I replaced glass in my canon 6820 puxma and seen a spring rolling around in there since the glass was broke I wasn't sure if it was to be in there also the arm won't return to scan goes all the way left but will not return to take copy
I am sorry Debbie but a printer mechanic I definitely am not. I can teach you how to print great photos 24 / 7 though! If the printer is worth it you might want to take it for servicing. Obviously something mechanical has broken in the scanner. I hope the printers is still able to at least print.
Christ, just say it already. How do you stop the freaking internal clock for the cleaningcycle?
OK. You can't! If I knew I'd tell you all!
love your lathe videos when you did them .
Thank and I will be doing more of that very soon.
This may be too old to ask, but do you have expierience with the IPF755, The other day I turned it on and booted straight to an error, So did a reset, Navigation+Load+power. Got into service mode. everytime i try to load paper I get a code 2f14, 2f13,2f2a, Can't figure this out, i use it to teach a graphic art class to students that can not afford a vo-tech, So I pay for everything, any ideas on what to try
Sorry Mark but do not I ow that model. Have you googled those error codes? Often after a lot period of non use they tend to through errors. Pull the p!it for about ten minutes, re plug and re power and see if that works. Otherwise, I'm afraid there is not much one can do with an old printer like that.
Just purchased the software, Muchísimas Gracias..!!
What software? Qimage?
Yes sir..
I am looking for a printer that I can print on CD and that I can change the waist pad my self. What printer can you recommend me?
Hardly any. I have an old AIO Epson Artisan 720 that would print to disks and had a user replaceable waste ink cartridge but it no longer made. None of the photo level printers will suffice. Look at the Expression series and see if they offer both of the functions you neee.
Does the timed for regular prints with Qimage requires the printer and the connected computer to be on?
Yes. Computer and printer and Qimage as well. Remember this is only keep the printer exercised and reduce the chance of logging. CANON's timed cleaning cycles will still occur regardless.
I have a Canon printer. I hate them. They keep changing to all colors. I do not do any photos. I only print documents.
I have to keep buying color carriages.The printer reverts back to all color to make black print.
Printers must use all color to print ANY document whether is is composed of only black or not.
My recommendation is to get a laser printer since you don't print photos.
What is the black carriage for??????? If printing text has to use the three color to print black. Printing a photo should be the same, Black is black.
This is not a stupid question! How does a laser printer print? What is the print median?
If you print bw documents buy a brother laser printer that takes toner NOT INK. Best $125 I ever spent!
Hi Jose can you recommend a simple budget printer where mostly i print black and white doc, bills and pictures (borderless print) from my hand phone and for home use only. I use to have a printer but i hardly use it this time i planing to get borderless printer to print some of my picture taken from the hand phone. Jose can you suggest me a one please, thank you.
I guess what you want is a all in one type printer. The problem is I have no idea about any of these model since I only use and work on larger Photo Only Printers. So I would not know where to even begin to suggest one. Canon and EPSON has goo AIO printer that also have scanners built in. Usually about $100 and up. Look for something that has WiFi so you can print through the smart phone.
Thank you Jose.
Jose can I use just a regular paper for cleaning, or it must be a photographic paper? BTW, I own Canon Pro 100.
Sure. Just regular copy paper.
Thank you, Jose.
The only time I recommend using a glossy photo paper is when performing AUTO nozzle checks or AUTO print head alignments. These AUTO tests require that the printed results be scanned and analyzed by an internal sensor. These results are sharper and easier to detect and be read by the sensor when printed on glossy rather than copy paper which wicks ink a bit more. Only some printers have these features. For simply printing nozzle check or purge charts you do not need special paper.
Jose Rodriguez Muchas gracias, Jose.
Jose Rodriguez Muchas gracias, Jose.
My low mileage canon mb5320 printer: Power light stays ON forever, the yellow light in the triangle stays ON as well. The printer is not working, the display window has no light ... totally blank. Canon tech asked me to replace the printer. Any tips?
It may be low.mileage but it is old.and printers so. called duty cycle of d# of print or # of years before they are done! Mileage is less important than time. I have two Epson pro3800s both ma y years old. One is still.working fine with 17K prints under its belt. The other one is the same age but died at about 5k prints. One has used heavily and one was not. I am nervously waiting for the other one did soon but at least I got a.to air prints out of it. So the bad news is that the tech for once is probably correct. Ultimately printers will succumb to time especially when not used often.
how would you guys schedule nozzle-cleaning-print jobs on a mac?
There is a little tool that someone from DPreview wrote just for MAC.
I have a Canon Pixma MG2920 printer I have replaced the ink cartridge several times before, but have just purchased 2- 245 Black cartridges and it keeps giving me an error that the cartridge isn't installed properly or is the wrong cartridge I have tried everything I can think of and when I diagnose and repair it says there is no problem
I really do not know as I do not use those printers. I only use and work with PRO level Photo printers. Are they OEM carts or compatible?
Jose Rodriguez I hve a question ,which printer do you think is the best and less expensive to use I do not print on a daily basis..Here are 2 I was searching on Canon Pixmz TS9120 or the Canon Pixma G-1200 mega tank injet printer...Are the mega tanks better and cheaper? Curious on what you think
You are asking the wrong guy but, generally The Megatanks G class Canon just like the L series from EPSON will be more economical to operate but they cost much more from the start. The truth is I do not use ANY non PRO level Photo Printer so I can't give you a direct answer from actual experience.
Thank you for your reply
Get a laser printer. Printing with ink is stone age.
Thank you so much for the information. I am getting ready to set up my Cannon Pixma Pro-10 that I have had sitting in the corner for about 2 years. I hope the ink has not hardened up!!! Silly me! Now I have subscribed to your channel and I am looking for your Patreon.com or I have tried Patrion.com to look for your website, and I just can't find it. Oh well. Again, Thank you so much for all of this wonderful information!
My Patreon link icon on the main channel page on the lower right of the channel art image. But just is case the URL is www.Patreon.com/jtoolman
Thanks and don't forget to join us tonight at 6 pm EST USA for the first live stream of the year.
Hello Jose, I have a sudden strange problem with my canon pixma mp530. Basically, once Printing the noozzles pattern test, it comes out only exactly half of the grid created by the cartridge PGBK. The lower half of the grid is blank. I've flushed it under hot water for a while, but only the colours came back to normal pattern. Any suggestions, please?
Unfortunately a 50% of the nozzle check blank on any channel means an permanent electronic failure. New print head will solve the problem unless your logic board caused the electronic failure to begin with.
Thank you for the prompt answer. In your experience, do you reckon that a new print head could have a reasonnable/affordable cost? Or it's not worth it?
Hi Jose, I'm loving and learning from your series of video blogs which include information I've never read before. In this video you mention that Canon printers should not be turned off because they have an internal clock to keep inks agitated and nozzles clear. You listed the printers involved from the Pro 9500 onwards. I have the Pro 9000 would you know if this printer has the same internal clock system? Thanks in advance. Andy.
The inks are not kept agitated. Basically its a timer that will trigger a cleaning cycle if you do not use the printer for 60 or more hours and yes, it also affect true PRO-9000.
Hi Jose thanks for your advice and help.
Hello, thank you for your info on Cannon printers. I let my cartridges run empty, or at least I thought. The black cartridge still printed but not thoroughly. I purchased new black and color cartridges. Now, although the printer prints as I test printed pages, cleaned thoroughly from printer panel, the ink cartridge supply ink levels keeps reading "information not available". Can you kindly send m e link or info on how to remedy problem. Thank you.
You left out which model Canon printer? I have never had nor heard of that error message. Are you using original carts?
Jose Rodriguez hi thank you for your reply. It’s a cannon pixma 492. Cartridges purchased at staples and microcenter. I do not get any errors such as lights or messages. It simply does not pick up the ink level and when I click it to find out. It says “information not available” I took the cartridges out unplugged machine put them back in and still no show. That was the only suggestion I could get from cannon support page for that machine. Thank you
Not a model I am experienced or familiar with as I only work with Pro Photo printers but if the carts are not original Canon cartridges, that will be a possible cause for the non recognition of the ink levels. If the are original then something's mg is damaged with the internal contacts on the print head contacts or the communication with the printhead to the printer
Jose Rodriguez ok well thank you anyway. May they are cheap refills via staples and MicroCenter. I will call cannon soon. I do appreciate your time. Thank you very much for being helpful to us. Be well.
If they are not OEM they will cause that problem.
My pro 1 bit the dust after 5 months of use.canon has stopped making them so they are sending me a pro 10 I will have some extra replacement chip for sale soon
Sorry to near that! Let me know when you are ready to let go of the chips.
Does Canon make LED printers? And if so what are the model numbers.
Sorry but I'm not entirely sure what an LED Printer is. Please clarify. Thanks
@@cheo1949 I believe it's a faster version of a Laser printer.
Don't know anything about those. I only deal with inkjet photo printers.
Hi Jose, I have a canon pro 100 because I saw your videos, but I cant print 4x6 always said paper jam......all other size is OK but 4x6 doesn't. Is there a trick that you can share > Thank you in advance
That should not be happening it should be able to print flawlessly in 4 x 6.
You might want to run the roller cleaning utility in the driver is located in the maintenance tab
@@cheo1949 Thank you....you are awesome.....I want another tip for you, I have canon photo paper Plus Semi-gloss, what paper for best result like photo printed at walmart photo center (it's said FUJI FILM) but no idea I need print photo from church.
-
Your Canon plus semi gloss is perfect. I like better than what the one hour shops produce.
Great tutorials.I couldn't understand the name of the site to make contributions. Can you spell it out?
I think you might mean www.patron.com/jtoolman
That is for automatic donation from $1 and up. Otherwise there a SUPPORT bottom on the mid right area of my main channel page for single one time support donations. Often it is called A Tip Jar.
Thanks!
Got it. Just started supporting you. I just got the Canon pro100 and want to finally understand printing. So far, you've helped a lot already.
Thank you Gregory I just saw that and I appreciate it. Hopefully I can make your experience with the PRO-100 a good one.
You have so far. Can you tell me which of your videos shows how to turn of printer color management. I'm not sure if I've done it right and can't remember which of your videos shows it. Thanks!
Preference driver window click on COLOR / Intensity Manual Adjustment then Matching then NONE.
Do you know how to reset the ink counter on the mx series to clear the end of life messages that you get when you hit 60,000 prints to reset it back to zero ?
There was a program made by an Indian tech student that could service a lot of settings in the printers that were the L series
It doesn't work for the newer MX models
Any help is appreciated
Thanks
Bill
Do mean you want to reset the waste Ink counter?? You need the WIC reset tool plus a $10 serial key for the reset. Get it from www.ocotoinkjet.co.uk But if you mean something else then I need more details. Realize that just resetting to zero does not remove all the waste Ink out of the pads. Eventually they overflow.
Jose Rodriguez the counter needs to be reset to zero. Cannon sets it so when it reaches the number it stops working and says end of life even though nothing is wrong.
I can clean or replace the pads
I thought there was a way to clear the counter from the buttons on the top using a sequence to get to that hidden menu
Wait are you talking about Epson or Canon here. New canons quite often cannot enter service mode unless you have access to the can on server along with login credentials. If Epson look to see if the WIC reset tool will work. Otherwise there is not much more I can tell you.
Thanks for the reply, Jose. Great content. I subbed!
Thank you!
Hi Jose, this is Hector. I have a Canon MG5720 Inkjet printer which I have not been able to use since new because the magente color would not print. I placed a tech report directly with Canon and they so kindly sent me a new headprinter in the mail. I replaced the headprinter and to my surprise nothing changed. I still have the same problem of the magenta color not being able to print. Somehow I am inclined to think that the printer has not registered within its local memory, I suppose, that it has a new printhead. If this makes sense, do you know a way to tell it that it now has a new headprinter ? or maybe you can tell me what other problem I may be facing. Thank you very much.
I have no idea as I only use PRO Photo printer. I know nothing about any of the MG models. Did you fully remove the vent tape on the magenta cart? If not ink will not flow and the printhead will burn out.
If you suspect the memory, why not download new firmware? I have a Canon MGxxxx, and I can reset some problems just by holding "Stop" for 5 seconds.
You need to run a nozzle check or a print through your printer every couple of days to prevent your printer from wasting ink on automatic cleaning cycles. Now you know everything from the video and skip the pain and suffering of watching it.
Sorry I put you through pain!
You obviously are not used to the format of our videos here.
It's more like a conversation and not a 1-2-3 of A-B-C impersonal do as I say in two minutes. If that is what you are looking for them I suggest you look.else.where.
Stumbled into your channel by chance. Just a question, isn't this ink printing outdated technology? Why not go with color laser printing which is hassle-free and isn't the resolution catching up? I think you could get size E and larger printers for some time. By the way my attention span is just a little under 9 minutes so I'd watched most of this video.
Thanks for watching by the way but....Outdated???? You are kidding right? LASER can not even come close to what you get from a 12 color Fine Art Photo printer. For documents and flyers, that do not require gallery level photo quality.... ok maybe! When I see laser printers than come even half way close to my quality then I might change my mind but that will never happen due to the simple totally different chemistry used by either technology. Those LASER Printed Photo albums and nooks you buy on line absolutely suck in comparison. I will put up with the inconvenience and babysitting you have to devote for the unbelievable quality you can get from a great inkjet photo printer. remember I am not talking about the junk you get a the local Staples Store.
There is no way to disable the cleaning cycle? Is this for all Canon printers? TY
Absolutely not. You prefer a clogged printer?
I prefer a printer that does not perform this task every sixty hours of non-use.
Good luck! Epson wont do that but they still do auto cycles after a long enough period.
I settled on an HP Envy. Great price at 29.95 clearence. Love it!
the BJC-50, 70, 80, 85 etc also seem to do this I own a few of these and have opened them and cleaned inside including the pads used for this. I still dont know how to make these printers pick a sheet of paper from loaded stack after a few years, any help with this would be helpful. also how to replace the battery pack for models with that option to extend recharge times
I am not familiar with this family of printers. Just how old are these models? When the paper refuses to feed after a year or so of sue is due to the rubber rollers no longer being "Sticky" so they can no longer grab the sheets of paper consistently!
Are these portable printers? I would assume their waste pads reach max load very quickly!
correct. the series was from about Win 3.0 through Win7 when Pixama came out as an upgrade. then mobile printers dropped out for some reason. the model numbers ran out of order also BJC-70, 50, 80, 55, 85, 90/pixima tru the 100s til Pixima was dropped then a few years til ink was dropped. I own several as I love the portable office ability with IBM laptops which I also have many
I remember seeing these on the old PC magazine. They problem was their internal ink pads maxing out very quickly! But they did seem very convenient at the time.
oh and the waste pads also disentigrate after long un serviced periods and seem unreplaceble without a whole part being changed but they are no longer supported so gotta tinker and DIY made parts from donors.
I have learned to get several of the tray cases that screw down air tight to store ink in between use and when traveling to save ink and printer problems. the battery pack has removable battery but havnt found replacement yet. likely costly also. I may try rebuilding it inside if I find a spare in case it gets damaged.
Hello Jose!
I have a PIXMA Pro9000 Mark II. After replacing an 8M and an 8PC, my printer stopped printing and popped up a window with a B200 error message. I removed the print head from the printer (which, to my surprise, was very dirty) and held it under the faucet to clean it out. I rinsed that print head about five minutes before the water was clear. After the print head completely dry (I'll let it air dry overnight), what do I do now? I can't afford to take my printer to a repair shop right now. Can you help me? I certainly hope so.
B200 is a print head failure! Thought it could possibly be something else but usually it indicates a new print head is needed.
Thank you, Jose. Where would I get a new print head for this printer (PIXMA Pro9000 Mark II)?
www.inkjetprinthead.com/canon_printhead_for_i9900_i9950_ip8500_ip8600_pro_9000_duplicate.htm?manf=5
Thank you, Jose. BTW, you said it could be something else. What else could it be? I would really hate to buy a print head (they're not cheap) and that's not the problem.
Actually that one is pretty cheap! Try $500!!!
When you removed the head and did your washing, did you unplug the printer? The reason is the recommended thing to do is to power off, remove the plug for about 20 minutes and then re plug and power up. Besides a damaged printhead it could something as simple as a bad contact of the back plate of the printhead to the contacts of the printer. If after checking that and doing the power off and back on it does not work then your only option is the new print head.
I have just purchased a PIXMA ts8050 printer can I use cis on it?
At your own risk.