Fontop Stainless Steel Glass Rinser Installation and Review
Вставка
- Опубліковано 15 тра 2022
- Easy to install, powerful jets, saves water, leak-free, durable and stylish looks. Amazon Affiliate Product Link: geni.us/dqXT
Buy direct from Fontop: fontopus.com/collections/glas...
You’ll receive an illustrated manual with detailed step-by-step installation instructions, a 2.5 foot flexible supply line and mini wrench, stainless steel base on a downward sloping angled wedge, actuator arm with stainless steel core and silicone top, mounting shank with pre-installed washers and nuts, and a T-adapter for your water line with two rubber washers.
The kit includes a small nylon washer that is meant to be installed over the spray nozzle, under the actuator to reduce friction, though technically it’s optional, and the unit functions fine without it. The small gray and orange rubber plug is a back check valve and should be installed with high-pressure water lines to prevent reverse flow that could potentially cause leaks when the water to the rinser stops flowing.
The glass rinser has a diameter of 5”, and length of 6” inches from the back to the front of the unit. The height it will sit above your countertop will be about 1.75”. The unit is made of solid stainless steel and feels durable and heavy-duty. It has a stylish brushed metal finish that will match other stainless fixtures and appliances. The unit activates when the actuator is pressed down and powerful jets of water emit in all directions from the small holes in the sprayer nozzle.
The assembly order will be the shank, then the base, the large rubber washer flat side up and ridge side down, metal washer, and lastly the brass nut. If you’re replacing an existing fixture like a soap dispenser, you’ll have to disassemble and remove it first which may involve unthreading mounting nuts or other components under the counter. Keep in mind that you’ll need at least 3.5” inches on center between fixture holes and 2.5” from the backsplash to the hole center in order to fit the base. In order for the water to drain out of the rinser into the sink, the lip has to extend over the edge of the sink, so the hole’s center should be within 3” of the sink’s edge.
To use, just place a glass over the actuator and press and hold down firmly. Powerful jets of water will shoot into the glass in all directions, reaching the bottom and all sides as long as the actuator is depressed, quickly rinsing out your glass in seconds. Because the base is angled into the sink, most of the water drains out of it, though there’s still a little left in mine, on top of the actuator and near the edge of the lip.
The rinser is water efficient as two presses dispense less than ¼ cup of water, versus traditional glass rinsing, which can use over a cup of water to rinse a single glass. The rinser works well with tall glasses too, like this champagne flute and the spray reaches all the way to the bottom of the glass. It’ll also work with mugs, wine glasses, and mason jars as long as the diameter of the vessel is less than 4.5”. My recommendation is to rinse with a series or quick bursts, rather than running the rinser for a few seconds. This is especially helpful when rinsing oddly shaped or narrow necks containers, as high volumes of water tend to pool in the bottle neck, preventing the jets from reaching the bottom of the vessel and potentially causing splashing.
Overall, this glass rinser was easy to install, works well, and cleans efficiently, rinsing my glasses quickly with less water than using the faucet. I also like that it looks great with my existing stainless steel fixtures and cleans up easily with a simple wipe with a dish cloth.
Amazon Affiliate Product Link: geni.us/dqXT - Навчання та стиль
Enter to win one for FREE: www.reviewedbyphil.com/p/giveaways.html Contest runs 6/27/23 - 7/5/23. Good Luck everyone!
this is the kitchen version of my wine-bottle washer.
I shall buy one when I get paid.
Go to the video I uploaded and in the comments there is a link to the product from which I purchased and received it_
Well... I have to say excellent job on this video. I was in search of a review and had no intention of watching an installation, but your video was so well assembled and the content was straight to the point that I found myself halfway through the installation before I realized it. Again... great video; excellent content.
This products consistent two things. One primary for rinsing and two washing(Secondary) with soap added
Most of the time its used for rinsing on a cup or small items. With, this shooting bombard spray of hydrojet it can lift any tough stain on the inside.
For washing using soap added its good too. Precautions its inside being wash not the outsideb
Thank you so much 🥰
You’re welcome 😊
Go to the video I uploaded and in the comments there is a link to the product from which I purchased and received it_
Nice review! It seems like a cool product. Do you find that you still need to wash with dish soap or is it clean enough without?
It depends. If it's an unsweetened water based drink like tea, black coffee or seltzer, no soap is not needed. But if there's dairy in it the fats from the milk typically require a quick wipe with a soapy sponge before rinsing and very sugary drinks may leave behind a sticky residue without soap.
Go to the video I uploaded and in the comments there is a link to the product from which I purchased and received it_
Have 1.5in to backsplash. Any ideas for attachments or ways to make it fit without drilling new hole?
To my knowledge, there isn't a great workaround for this issue. If the clearance isn't there, then you won't be able to install the glass rinser without drilling a new hole elsewhere. I have seen some installations with the hole drilled to the side of the sink or overhanging one of the back corners.
I’m curious, the glass washing doesn’t cover the surface outside the cup where the lips would usually keep in contact with. So would u end up washing that portion separately first?
Yes
Yes separated it's better this is primary for rinsing and secondary(Washer) when used in soap a bit added. It's for quick rinse even the toughness stain can handle because it bombard with fast strong hydrojet sprayb
Bonjour, pouvez vous me envoyer le mode d installation papier, merci 😊
But what happens to water pressure to the cold or hot water!? Does it affect the pressure of the water when not in use!?
No, your water line pressure will not be affected when not in use because pressurized lines always return to equilibrium when water is not running.
How big is the hole u need to drill in countertop to install?
The standard faucet hole size is 1-3/8 inches
Any idea what to do if sprayer won't turn off?
Not sure, sounds like the spring isn't popping back up to shut off the water flow. Perhaps the water pressure in your line is too high. In that case, you can try partially closing the valve to the water line and see if that reduces the flow enough for the sprayer spring to actuate and shut off.