Suggestion: How about "Vertical support risers" for each side of the turn drum? When the river raises, the drum would raise too. With (5' - five feet of raise) from (4) 6ft pieces of pipe, (2) anchors one top and one bottom, fear of wash-out is lowered.
Is it possible to lift water up to one hundred meter height with this pump. Please guide me . I want to apply this pump at my home to lift water up to 100 meter height.
Luiz com relação a ocorrência de "enxurradas", acho que poderia ser utilizada uma plataforma flutuante que acompanharia a elevação do nível do rio e, desde que estivesse bem ancorada nas margens, evitaria o risco de perda da bomba. Parabéns! Belo projeto!
Obrigado pela ideia. Eu só tenho medo de algumas enxurradas que são mto fortes mesmo heheh esse ribeirão é bem estreito pela vazão que tem. Ele nasce num conjunto de serras e em alguns temporais a água sobe mto chegando a alagar os pastos e tem uma velocidade incrível
I could see 4 in a row pumping to a elavated pond or tanand and then dishcharge into a micro hydro plant an discharge before the pumps to reduce water loss.
You tub video The air that is trapped in the pump helps to lift water by displacing water. Water in a vertical column is .44 psi pounds a foot. If half that column is air you can lift twice the hight at same pressure. In pipe bigger than 3/8" air bubbles can pass the water. The pump I made I put a water/air separator. It is a 3" abs pipe with intake from pump at top, a 3/8" hose the travels 150 feet to a 80 foot hight, and a 5/8" hose that rise 55'. In 24 hours it lifts 500 gal. to 55 feet and 700 gals. to 80 feet using 21 psi of pressure. At 25 psi pump stops working and 27 psi it pushed the water back out the intake. Because there is no valves the weight of the water in the loops of the pipe is what the column of water pushes off of. Increase the water being taken in each turn of the pump or increase the amount of loops in the pump you will increase hight the water can be lifted. 1 pound of water (1 pint or .5 liter) 2 feet of lift. It looks like your pump is taking in .5 liter a turn times your loops will give you max that your pump can lift without air in water. The air will displaces some of the water in the pipe making it able to lift it higher. The pump looks very well built and gives you the hight you want. Well done! Stream powered water pump.m.ua-cam.com/video/rIVDgHx3XBc/v-deo.html Stream powered pump lates designRotary valve slide show m.ua-cam.com/video/b9u-sUJY5Lk/v-deo.html Rotary valve installed m.ua-cam.com/video/vyzXEiJEDQE/v-deo.html Floating barrow water pumpm.ua-cam.com/video/rIVDgHx3XBc/v-deo.html
under stand the sudden high water issues there...but what if you made that a bit lighter without using a wooden wire spool, like just make a frame of the water wheel & paddle parts?? I believe a shade bit lighter in the frame (Alum) would also allow you to use two old hot water tanks (stripped down) and holes sealed and use them on both side like a pontoon instead....it would float at the level of water and if properly tied to trees will only go up and down with the water...??
+Pedacinho do Céu Construção Obrigado! Então essa parte realmente eh a mais difícil. Eu, neste projeto, utilizei uma peça que é utilizada em bombas de combustíveis que são acopladas ao gatilho. O nome dela é união giratória. Pode ser encontrada em lojas que vendem peças para postos. Uma observação: Ontem mesmo coloquei para funcionar uma outra bomba. Observei que quanto maior o diâmetro do eixo central maior será a pressão. Recomendo vc fazer esta bomba com um eixo de no minimo 10cm de diametro e 100 metros de canos 3/4''(50m de cada lado)
Ficitaciones : una pregunta ¿ en el video solo se observa la entrada al eje central de una sola manguera y la otra manguera del otro lado como se acopla???
luis buenas noches yo estoy tratando de hacer algo así pero mi problema es la union giratoria no se como o que poner me podrías con ayudar diciendo que metodo usaste o uniones
+Josep Smaravilla ¡Hola! En el video he usado una pieza llamada articulación giratoria. Es una pieza difícil de encontrar. Tiene un proyecto en el sitio lurkertech.com/water/pump/tailer/ que enseña a hacerlo. Otra solución que encontré fue a comprar esa pieza que se une a una manguera de la bomba de combustible. Esto es fácil de encontrar en las tiendas que dan asistencia en bombas de combustible.
You should put a 4-6" pvc pipe check valve on the end that scoops the water... you're losing half of the water that's scooped on every turn... allowing air to get in... the gate would slam shut with the water in it until it's submerged again... could pump twice the water... less gaps...
I used a piece called swivel joint. I found this piece in store sales of gas station pumps. thumbs.dreamstime.com/t/bocal-da-bomba-do-posto-de-gasolina-11271853.jpg
+EdinUNI DESIGN7 Hi! The pump could elevate 300 liters per hour (7,200 liters per day) at a height of 18 meters to 13 rpm (in video). Now at the start of the rainy season, the pump speed increased to 18 rpm and the flow rate increased to about 450 liters per hour. At the end of the rainy season the wheel will turn around 25-30rpm and consequently the flow rate will increase proportionally.
Qual a vazão do rio? As vezes é necessário que se crie um desnível no rio para que a energia potencial da água se converta em energia cinética. Este ribeirão do vídeo tem uma vazão na seca de 1,5m^3/s. Recentemente aumentei o desnível do rio naquele período e consegui ligar 2 bombas em série.
Seria possível você me enviar por email os detalhes e procedimentos para construção. Já pedi para muitas pessoas que postam esses vídeos mas ninguém ajuda. Estou precisando e vejo outros interessados também nesse tipo de roda. Se puder ficarei muito agradecido. Talvez você não tenha um projeto,.mas basta uma sequência de orientações , um passo a passo. Obrigado
Good idea! I live directly to a stream and I am currently working on a pump too. The wheel is constructed. Next comes the spiral. I want to pump up the water up to 2,5m. Do you think it would work with your pump?
Wow - what a beautiful location to test a spiral pump and somewhat similar to ours. Did you do any later adjustments and is the pump currently in use? Must be something similar to our location. 1.1 gallons per minute is a starting point and you seem to be pumping a fair distance up. As I'm sure you realize, there are some easy minor adjustments which should give more pumped water volume. If you or any of your fans are interested, we have started a public facebook group for water wheel pumps discussions - please join in: facebook.com/groups/240458583255303/
Boa tarde, vc tem whats preciso tirar uma dúvida,a minha roda depois de uma certa altura ela trava para de virar, 50 metros dos dois lados de mangueira de 1 polegada, a mangueira que leva a água é de meia polegada, mesmo com válvula de retenção a roda trava depois de uma certa altura, se tiver whats me chama 19 99880 3551, obrigado!!
Well done! Yours is very well built and strong, very good! Stream powered pump lates designRotary valve slide show m.ua-cam.com/video/b9u-sUJY5Lk/v-deo.html Rotary valve installed m.ua-cam.com/video/vyzXEiJEDQE/v-deo.html 1 1/4" pipe thread to 1" hose barb, 1 1/4" p trap, 3/4" pvc thick wall pipe (use slice from slip on end as stop), 5/16 in. x 1-1/2 in. Zinc-Plated Fender Washer, 1/4 in. x 1-1/4 in. Zinc-Plated Fender Washer, cut a piece from p trap to slip in hose barb, 3/4" copper pipe, 1/2" female thread to 3/4" copper sweat fitting. From eBay 12" by 1/4"-100% GFO Marine Shaft Packing (Gland Stern Stuffing)
LOVE the music! Thanks for sharing this. Hope this helps me fix my irrigation problem.
What did you use for rotary joint?
So smart!
Thank you so very much for sharing this video!
This is one of the the technologies that the world needs. Together with small scale wind and solar Not nuclear power.
Suggestion: How about "Vertical support risers" for each side of the turn drum? When the river raises, the drum would raise too.
With (5' - five feet of raise) from (4) 6ft pieces of pipe, (2) anchors one top and one bottom, fear of wash-out is lowered.
thank you - have been looking for this for a long time.....
We don't need the music, but we need this kind of pump
Is it possible to lift water up to one hundred meter height with this pump. Please guide me . I want to apply this pump at my home to lift water up to 100 meter height.
that looks like a simple design...will definetely do it...genious!
+Ahadi Luhanga : Thanks!=]
Any idea how the water outlet is connected to the hose?
Luiz com relação a ocorrência de "enxurradas", acho que poderia ser utilizada uma plataforma flutuante que acompanharia a elevação do nível do rio e, desde que estivesse bem ancorada nas margens, evitaria o risco de perda da bomba. Parabéns! Belo projeto!
Obrigado pela ideia. Eu só tenho medo de algumas enxurradas que são mto fortes mesmo heheh esse ribeirão é bem estreito pela vazão que tem. Ele nasce num conjunto de serras e em alguns temporais a água sobe mto chegando a alagar os pastos e tem uma velocidade incrível
uma distância de 400 metros do rio e uma altura de 30 metros, quantos litros ela joga por hora?
What is the solution for rotary joint. Is there any kind of joint available in market? Please let me know. Thank you for your video.
I could see 4 in a row pumping to a elavated pond or tanand and then dishcharge into a micro hydro plant an discharge before the pumps to reduce water loss.
What its sad its that there are many beautiful machines like this, but in youtube nobody, almost nobody xplains to others.
You tub video The air that is trapped in the pump helps to lift water by displacing water. Water in a vertical column is .44 psi pounds a foot. If half that column is air you can lift twice the hight at same pressure. In pipe bigger than 3/8" air bubbles can pass the water. The pump I made I put a water/air separator. It is a 3" abs pipe with intake from pump at top, a 3/8" hose the travels 150 feet to a 80 foot hight, and a 5/8" hose that rise 55'. In 24 hours it lifts 500 gal. to 55 feet and 700 gals. to 80 feet using 21 psi of pressure. At 25 psi pump stops working and 27 psi it pushed the water back out the intake. Because there is no valves the weight of the water in the loops of the pipe is what the column of water pushes off of. Increase the water being taken in each turn of the pump or increase the amount of loops in the pump you will increase hight the water can be lifted. 1 pound of water (1 pint or .5 liter) 2 feet of lift. It looks like your pump is taking in .5 liter a turn times your loops will give you max that your pump can lift without air in water. The air will displaces some of the water in the pipe making it able to lift it higher. The pump looks very well built and gives you the hight you want. Well done!
Stream powered water pump.m.ua-cam.com/video/rIVDgHx3XBc/v-deo.html
Stream powered pump lates designRotary valve slide show m.ua-cam.com/video/b9u-sUJY5Lk/v-deo.html
Rotary valve installed m.ua-cam.com/video/vyzXEiJEDQE/v-deo.html
Floating barrow water pumpm.ua-cam.com/video/rIVDgHx3XBc/v-deo.html
under stand the sudden high water issues there...but what if you made that a bit lighter without using a wooden wire spool, like just make a frame of the water wheel & paddle parts?? I believe a shade bit lighter in the frame (Alum) would also allow you to use two old hot water tanks (stripped down) and holes sealed and use them on both side like a pontoon instead....it would float at the level of water and if properly tied to trees will only go up and down with the water...??
Tq for sharing my friend.. its help me alot
Very nice project. impressive
If you put a 1/8"-3/16" hole at the neck of the bottle it will allow the air to escape and more water will be scooped up.
Love the background music
I thought that was the theme song of pirates of Caribbean (WAIT IT IS!)
Can we use it to transport water up the mountain? For a height of thousand feet?
Yes, but all the system itself must be increased.
Один виток сколько метров подымает?
how make rotary seal..give me video bosse
Muito bom mesmo parabéns, preciso fazer uma urgente, só não sei o nome desse ferro que gira com a mangueira, poderia me falar essas conexões ?
+Pedacinho do Céu Construção Obrigado! Então essa parte realmente eh a mais difícil. Eu, neste projeto, utilizei uma peça que é utilizada em bombas de combustíveis que são acopladas ao gatilho. O nome dela é união giratória. Pode ser encontrada em lojas que vendem peças para postos. Uma observação: Ontem mesmo coloquei para funcionar uma outra bomba. Observei que quanto maior o diâmetro do eixo central maior será a pressão. Recomendo vc fazer esta bomba com um eixo de no minimo 10cm de diametro e 100 metros de canos 3/4''(50m de cada lado)
+Luiz Henrique Machado será que podemos conversar mais, 71-991237644 zap
parabéns cara ...uma execelente soluçao pra falta de água cara uma duvida qnts nilimitris e essa mangueira
A mangueira é de 3/4 de polegadas
Ficitaciones : una pregunta ¿ en el video solo se observa la entrada al eje central de una sola manguera y la otra manguera del otro lado como se acopla???
La otra manguera se acopla en el otro lado del eje. Ella no apareció por qué la rueda estaba en frente de la visión en el vídeo.
luis buenas noches yo estoy tratando de hacer algo así pero mi problema es la union giratoria no se como o que poner me podrías con ayudar diciendo que metodo usaste o uniones
+Josep Smaravilla ¡Hola! En el video he usado una pieza llamada articulación giratoria. Es una pieza difícil de encontrar. Tiene un proyecto en el sitio lurkertech.com/water/pump/tailer/ que enseña a hacerlo. Otra solución que encontré fue a comprar esa pieza que se une a una manguera de la bomba de combustible. Esto es fácil de encontrar en las tiendas que dan asistencia en bombas de combustible.
gracias luis
conector click truper
Preciso de uma dessas. Esta roda foi feita com aquelas bobinas de fio elétrico? Como foi feito esse eixo, os rolamentos? Como saber mais detalhes?
Exatamente.. A roda foi feita a partir daquelas bobinas mesmo. Eu comprei o eixo e os rolamentos em um ferro velho
i like a musical water wheel,,,,never heard one before
Another one, if you like! hehehe => ua-cam.com/video/7TuSU-R-3ng/v-deo.html
muy bueno e ingenioso, q altura eleva al agua?
18m
Un ejemplo: bomba diametro 2m; distancia 1,5km, cantidad 7500 litros/dia => 9m de elevación
You should put a 4-6" pvc pipe check valve on the end that scoops the water... you're losing half of the water that's scooped on every turn... allowing air to get in... the gate would slam shut with the water in it until it's submerged again... could pump twice the water... less gaps...
We will build one model so I was thinking about the check valve too!
Para Ecuador você tem um distribuidor que venda a bomba
The pressure that is made is caused by compressing air in the hose. this means it can pump long distances! :D
joe m but he lives on a cattle ranch. So I don't like him.
What If i use 4inches hose you think its gonna work?
I think so, but the lift height will be low
What do you use for the union that allows the pump to turn without twisting your outlet hose?
I used a piece called swivel joint. I found this piece in store sales of gas station pumps.
thumbs.dreamstime.com/t/bocal-da-bomba-do-posto-de-gasolina-11271853.jpg
that is pretty clever! Does the ball socket not wear out quickly with the constant movement?
Hi Luiz, do you have a figure or a rough guide for the volume of water collected per day/ per hour?
+EdinUNI DESIGN7 Hi! The pump could elevate 300 liters per hour (7,200 liters per day) at a height of 18 meters to 13 rpm (in video). Now at the start of the rainy season, the pump speed increased to 18 rpm and the flow rate increased to about 450 liters per hour. At the end of the rainy season the wheel will turn around 25-30rpm and consequently the flow rate will increase proportionally.
Douglas Barclay, @@haisergyn Another example: pump diametre 2m; distance 1,5km, flow 7500 litros/dia => 9m de elevation
Really! do you have a video of your model? @@combonianosbrasil
I don't have such video. The figures I gave came from calculations done in the project,😀 @@LuisAlbanes
@@combonianos.brasil thank you
Cuanto metro de altura arroja
18m de altura a uma distância de 160m em linha reta
what is the first piece of music name?
Marcus Viana - Escarlate
great ...please make video how to make
water utilization good
2022 e olha nós aqui! 💗
Um pé em 2024 e olha nós aqui kkkk
Boa noite, quantos metros de mangueira vc utilizou na roda?
Boa noite. Utilizei 100 metros (50m em cada lado)
Luiz Henrique Machado fiz a minha porém ela para de rodar qdo enche a mangueira que manda para o alto.
Qual a vazão do rio? As vezes é necessário que se crie um desnível no rio para que a energia potencial da água se converta em energia cinética. Este ribeirão do vídeo tem uma vazão na seca de 1,5m^3/s. Recentemente aumentei o desnível do rio naquele período e consegui ligar 2 bombas em série.
Luiz Henrique Machado vazão não sei mas é bem forte, vou mudar a roda em breve aviso Vc, valeu obrigado ! Whats 19 99880 3551
Seria possível você me enviar por email os detalhes e procedimentos para construção. Já pedi para muitas pessoas que postam esses vídeos mas ninguém ajuda. Estou precisando e vejo outros interessados também nesse tipo de roda. Se puder ficarei muito agradecido. Talvez você não tenha um projeto,.mas basta uma sequência de orientações , um passo a passo. Obrigado
Fiz uma dessa muito top
owsome project knowledge
quantos litros/hora ela joga nesse exemplo do video?
Ela joga 300 litros por hora na caixa d'água que fica a 180 metros do rio a uma altura em relação ao nível da água de 18 metros.
@@haisergyn hola cordiales saludos desde Mexico, cial esnla altura máxima que puede alcanzar una bomba de espiral.?
@@Cholate.enbola20 m de altura (eje z) y 180 m de distancia (eje xy)
Good idea! I live directly to a stream and I am currently working on a pump too.
The wheel is constructed. Next comes the spiral. I want to pump up the water up to 2,5m. Do you think it would work with your pump?
make a wheel of 2.5m diameter and your problem is solved.
Top idea
Hola. los invito a ver el vide "COALCOMÁN. ELEVAR SUBIR AGUA RIO MANGUERA" Está muy bien explicado sobre la forma en que funciona el artefacto.
music made me feel like i was playing runescape. mining coal and fishing while botting
increible :)
I love me some depressing harpsichord and mandolin
Wow - what a beautiful location to test a spiral pump and somewhat similar to ours. Did you do any later adjustments and is the pump currently in use? Must be something similar to our location. 1.1 gallons per minute is a starting point and you seem to be pumping a fair distance up. As I'm sure you realize, there are some easy minor adjustments which should give more pumped water volume. If you or any of your fans are interested, we have started a public facebook group for water wheel pumps discussions - please join in:
facebook.com/groups/240458583255303/
muito bom
Look at Aqysta! They made this pump commercially
Why? Could you give reasons?
i like this omg
Boa tarde, vc tem whats preciso tirar uma dúvida,a minha roda depois de uma certa altura ela trava para de virar, 50 metros dos dois lados de mangueira de 1 polegada, a mangueira que leva a água é de meia polegada, mesmo com válvula de retenção a roda trava depois de uma certa altura, se tiver whats me chama 19 99880 3551, obrigado!!
brasil 2019
68 non likes work for the power and water company
Spiral way to heaven 😂
show Luiz
Dislike the background music
If you have a couple of oxen, try this:
docs.google.com/presentation/d/1aHDumJvA6Pz7EEN5T8tXfh_3qmkgGb8GpoHXiTNVLtk/edit?ts=58e3ff69#slide=id.p
wearing gunboots and then letting them fill with water. Must be Irish
this is said muisic
and cool
This video makes me very sad.
Oh~~^^
Well done! Yours is very well built and strong, very good!
Stream powered pump lates designRotary valve slide show m.ua-cam.com/video/b9u-sUJY5Lk/v-deo.html
Rotary valve installed m.ua-cam.com/video/vyzXEiJEDQE/v-deo.html
1 1/4" pipe thread to 1" hose barb, 1 1/4" p trap, 3/4" pvc thick wall pipe (use slice from slip on end as stop), 5/16 in. x 1-1/2 in. Zinc-Plated Fender Washer, 1/4 in. x 1-1/4 in. Zinc-Plated Fender Washer, cut a piece from p trap to slip in hose barb, 3/4" copper pipe, 1/2" female thread to 3/4" copper sweat fitting. From eBay 12" by 1/4"-100% GFO Marine Shaft Packing (Gland Stern Stuffing)
wwe top 10
lux 1
How is the Fish? How do the Fishes travel downstream? Do you want to kill them all?