Putting A 460 HP LT1 Into A '71 C10 - Truck Tech S3, E9
Вставка
- Опубліковано 27 сер 2024
- On this episode of Truck Tech the classic '71 C10 pickup returns for custom brakes, fuel system plus cab repair
PARTS USED IN THIS EPISODE:
HP Tuners, LLC.: HP Tuner, VCM Scanner, Reads PCM & TCM Codes, Kit
More Info: pntv.us/pn_pt_...
Yukon Gear & Axle: Dura Grip Positraction Carrier, Traction-Loc, GM 8.875 in., 30 Spline, 3.08 to 3.90 Ratio, Each
More Info: pntv.us/pn_pt_...
Yukon Gear & Axle: Ring and Pinion Gear Installation Kit, Master Overhaul Kit, 30 Spline, GM 8.875 in., Kit
More Info: pntv.us/pn_pt_...
American Powertrain Systems: Tremec T-56 Complete Manual Transmission Conversion Kit With Hydramax Hydraulic Slave Kit, White Lightning Shifter, And Quicktime Bell Housing
Baer Brake Systems: 13" Front Track4 Brake System, 1960-1987 C-10, Front Systems, Vehicles with CPP 2" Drop Spindles 5 Lug
Baer Brake Systems: 12" Rear SS4 Brake System with Park Brake, 1960-1987 C-10, Rear Systems, Stock 12 bolt 5 lug
Brothers Truck Parts: Pre-Bent Brake Line Kit, 1971 Shortbed - Rear Coil - Brake Lines - 1/2 Ton - Power Disc - Steel
Brothers Truck Parts: 63-72 Gas Tank - Underbed - Aluminum
JBA Performance Exhaust Co.: Headers, GM, LT1, Full Length
JBA Performance Exhaust Co.: Headers, GM, LT1, Shorty
LMC Truck: Front Cab Support
LMC Truck: Grille - Radiator Support
LMC Truck: Inner Fender - Primed
LMC Truck: Front Bed Panel - Steel Floor
LMC Truck: Bed Floor Assembly
LMC Truck: Cab Corner
Pace Performance: Prototype Front Accessory Drive System For GM Lt1 Engine
Pace Performance: LT1 Wet-Sump 6.2L 460HP Crate Engine
PowerTrain Products: One of the nation s leading supplier of remanufactured, rebuilt and used engines, transmissions, differentials, transfer cases & cylinder heads. Providing you with an industry-leading, nationwide parts & labor warranty of up to 4 years
The Industrial Depot: The Industrial Depot - Fasteners, Hardware, and Shop Supplies
We'll continue to post these episodes here on UA-cam. If you can't wait for the rest of the build, visit our site to binge-watch: www.powernationtv.com/shows/truck-tech
Ekdkdkdd
I want to swap my 1986 Monte Carlo luxury sport any info on that can't really find much out here about LT swaps
This was the best 20 minute commercial I've ever seen.
There's more..
FYI at 12:03 the replacement support from lmc is designed to fit over the existing bracket so you don't have to remove the old one. At least that's what we did. There was also minimal rust
Nice show truck definitely not a average guy job.
Man this series is so much better than the "Week to Wicked" series. Thanks for giving them some much needed competition. Cheers
For the money your sponsors put into the pretty new engine and everything else, I could get me a really nice used truck. I wish I had a shop with a lift, a hoist, and any tool I wanted.
Keep dreaming
You can do this in a garage.
5:19 brought me a wholesome feeling. One day I look forward to buying a transmission from this manufacturer.
yo vi ala virgen jsjsjs
@@adantrejo3854 y si Todas las transmisiones salen con su bendición
I thought Tremec was in my home state Queretaro... But than again they said north America... Mexico is north America. 👍
Looks like I need to get the LT1 in my garage up and running
Oh God they put new brakes on. The comment section is going explode that the average guy can't afford them. 😆
When you get this project done I'd be glad to test it out for you!!!!!
"Thats not the best place for a gas tank " I totally agree, while at the same time GM has me driving pretty much on top of my plastic gas tank. 08 rado. Go built in the USA
Nice y'all putting out the 2001 videos 👍
"Posi-tively cool", sheesh Dad
Great Information 👍🏻
Thanks
17:35 No reason top replace those axle seals after spending $600,000 on brakes and carrier.
You' re the Best .
Awesome informative Video experience Y'alls God Bless Ya 🙏
Did he really pour shade on eBay @8:47? 🤣😂🤣😂 we not all rich I check there first always
I gotta put one of these in a 96 Impala
Smh the box and bubble Chevy era is over!
Smh a good Impala will never be over
I hear you!! I got my 96 SS daily with the stock lt1 ....
I like the c10
Just wait till that direct injection carbons up.
Murphy Davis maintain it clean
The AFM system fails too often. Every body deletes them when they find out how often they fail and how expensive it is to repair.
Good work guys!
GM should not have used the name LT1 on anything newer than the 1972 Z28 and Vette. The LT1 was used on the 70 to 72 Z28 and the Corvette.
yes I agree they fuck up
John Milner lack of creativity when it comes to marketing. Wife’s 2007 Tahoe LTZ started rusting inside 3 yrs at the door skins. Paint peels without any history chipping. Wheels rusted in 3 yrs and wouldn’t hold air. Cheap ass engineering. They want high dollar price for old school Hyundai engineering, who definitely upped their game. GM get your shit together!
we are aware of that fuckface
The GM direct injectors fail at an alarming rate
Have fun !!
What do you drive?
Ha-Ha, tell em! I knew that one, that's why I drive a Ford , shits from 65 and still burning sum lightly mod gm Turds.
gee thanks. Now i got that to look forward to
What automatic transmission would you use in a similar situation?
(Edited: this will take longer than 19 minutes to complete. Results may vary)
Surprised they didn’t go with the TR6060 Manual transmission
Brake discs installed wrong - left on right and right on left
Nice
Great work 👍
Gonna have a strange vibration,didn’t install input shaft bearing.
vilsiran 17:12
Hey guys why you never anwser the questions the fans ask i got a 1970 c10 i like to restore how i can get a cuote
Nice 👍 guys I like your work!!!!!!
What will be your suggestion for Burb 1999 K1500. I have 10k budget wouldlike to change engine and gearbox? What are your suggestions within this budget ?
I wish they would have put the 8 speed in, but a 6 speed has it's place.
Weird tip: black nail polish...it dries hard, and comes with a small brush.
About a buck for the cheap stuff.
After drilling a hole it can be used to protect the metal. ¯\_(ツ)_/¯
Never use a impact on any bolt in a rear end they are very hard and will crack seen it many times
please dont advise the comments section
@@trillrifaxegrindor4411 i can say what i want douchebag
Just so you know..... New battery for your vernier calipers costs about 50c 😕
Why is that man wearing gloves handling brand new parts that ain't even dirty
I love the truck, and the host are outstanding.
My complaint goes to the producers,...
That motor will run into the neighborhood of 15 to 20 grand.
The frame and suspension upgrades have to be tipping the scales at around ten grand, and you haven't even gotten to the body and paint, or the interior.
Very very few of us are going to go 40 to 50 grand on a pickup.
I know your promoting for an aftermarket parts company, but a lot of us are tired of being told, that our dream will have to stay a dream.
Find something that you can build, ( and look good) for ten grand.
You'll be shocked at the number of customers buying their products after that.
Can't do that?
Okay, cater only to the rich, and watch the rest of us stop tuning in.
enjoy the video,realize it isnt made so you can duplicate it.do what you can afford,no one wants to watch you refresh a 125 horsepower 305 with a spray can.this is a scripted commecial
@@trillrifaxegrindor4411 actually, the youtube show " Roadkill " has become a regular tv show, and zipties and spray can paint is their speciality.
Stacy's from Boise, Boise is a Republican State, the Republicans would sale their own mother's blood to make a profit.
Simple equation, easy to understand and prove.
I like Stacy, but he should have tried a little harder to go low buck, or just told the truth about our chances to aford much of anything at all.
If your making it better then others, bless you, but yes, they do expect you to spend that kind of money.
That's why a paint shop qouted me 10,000 dollars, just to respray a 63 chevy pickup.
You have the floor,...show me one car, ( not gotten from a family member) that was posted ( looks great) made before 1976,...that only has ten grand invested in it.
Why can’t I find find the other episodes?
Meh.. your just adding overly complex engine with headaches for future owners. SBC, or BBC... done.
hawkdsl i agree! Add a Holley carb, all set.
Ok
Hey anyone have any advise on putting this engine in a 96’ Impala SS, ie…accessories, best trans combo & fitment?
Why weld in a bolt in tunnel? Bolt it in.
I guess all of L.T. co-host must be shorter than him...🤔😄
In the real world, what does all this cost ?. Excluding labour. [ Sorry guys Aussie spelling!!! lol.]
about 20k ....think ls3
@@alt7488 w2r1221dvd
use the internet to your advantage
So basically its vvt direct injection engine
How much did that LT1 cost? 10k - 12k? No one ever talks about cost of these projects. At the end you've spent $100k for a $35k truck... I have a 1972 C-10 and would love to do stuff like this but the ROI always stops me which leads to frustration. Results in just dreams and not action. Nice video however.
I like watching you guys build those vehicles but I can't stop laughing at the way you talk. Ending each sentence with the same accent. This must be a production thing. Still laughing.
Yep...All the hosts do it
Ok, did you film the C 10 paint, or the finished truck? Great job.
would like to know what kind of a tool brand your using
I wish I coulda done this to my 69 when I had it. It was my daily driver for years. Had a mild 350, 350 turbo, and 4:11 gears. It was NOT good on gas lol. The lock in torque converter didn’t even work. It pretty mich stayed in 3rd gear all the time and it was already screaming at 55mph. But I miss the old days of hearing gas slosh around in the cab lol
What about the pedal assembly
Daniel Leighton it’s not that hard to find a manual pedal set these trucks did have a manual transmission option
Too bad the fuel tank wasn't placed in a more safe position
GM designed some trucks with the tank outside the frame, these guys didn't do too bad.
hello what is the price of that 460 hp LT1, Is automatic or lever to the floor?
pace performance
Id delete that garbage AFM while the engine is out.
AFM is one of the worst ideas GM ever had, alot of work to fix them, which is why they make kits to eliminate it
When cars go electric it'll just be slapping in a motor and slapping a battery
Eso videos de pm son aburridos porque siempre los dejan cortados,se vuelve uno loco buscando en dónde continua
Just bolting things together. Not really any fabrication here....
Holley offers all of the swap components that are needed for this engine swap.
www.holley.com/products/engine_swap_parts/lt_swap_systems/1967-1972_c10_2wd_lt_swap_components/
No Opti spark.... it’s not a real LT1.
It's the newer generation LT1, not the one from the the 90s.
Original LT1 came out in the 70s
John Crankshaft close- that was an LT-1.
note to exceptionally stupid people :you will not see every element of the build in this video,don't comment on the things you dont see happen.
use your brain occasionally,stupid fucks
Hello, what is the price of an LT1 engine?
pace performance......check it
Direct injection and AEM sucks!
DIDNT DO AXLE SEALS??/
not in real time,idiotfuck
@@trillrifaxegrindor4411 F U IN REAL TIME!...LOL..
Yeah that's cool and all, but it looks like a pain when shit brakes.
At least you know the vehicle will slow down when it brakes
its not built for you,you couldnt afford a bicycle
@@trillrifaxegrindor4411 Yeah.Good.Okay. lol.
When msje a program un.spanish
Burn it in? Really? Why not just weld it off? Aaha ha ha ........
Talked so much
LT expensive
😢 Why would you destroy that truck by putting a newer motor and it? It's just gives all these idiots out of here. Another dumb idea to ruin a value of vehicle.
Cala boca
These shows are so unrealistic lol not everyone has 500 million dollars to buy all the parts they use. cool to watch tho.
I run the car maintenance UA-cam channel in Korea. I'm always learning such a great ideas on your channel. I hope we have a chance to be together. Thank you.
These shows are all about sponsors, like a 20 minute freaking commercial. I had to stop watching, can't stand the way you talk!
United by ducks! 1st view and like!
Lol, cringeworthy fake voices.
2nd view “ ha ! 🤘
Nice job guys. It helps to have a $500K shop and tools. When DOGECOIN hits 1000 I'll get one!