Trailer Brakes 101 And How To Diagnose Wiring Problems Yourself !!!
Вставка
- Опубліковано 8 вер 2024
- GO TO MY WEBSITE AND BMW FORUM !!!
www.nathansbmw...
CLICK HERE TO BUY YOUR NEXT CAR PARTS FROM MY AMAZON STORE
www.amazon.com...
Trailer Brakes 101 And How To Diagnose Wiring Problems Yourself
/ nathansdiygarage
/ nathansdiygarage
/ nathandiygarage
Send stuff to my PO box for products you want reviewed or for a shout out on the channel,
Nathans DIY Garage
PO BOX 115
Altenburg MO
63732 For Business Contact :
Nathan's BMW Workshop
Po Box 115 Altenburg Mo 63732
nathan.youtube@yahoo.com
I agree with you about replacing the front end of that harness. Actually, after seeing that burnt wiring, I'd replace all of it so it's new. I like to go with the one piece plug harness and terminal box, mounted to the frame and go with all new wire and run it in conduit. Even something as simple as PEX pipe or EMT secured to the frame will keep the wires safe from damage. The time, effort and cost is worth it once it's done because you won't have any wiring issues for years to come - if ever. Cheap peace of mind in my opinion.
Thanks for sharing.
I am new to trailers. I’ve bought three in the last year, all from different manufacturers. Two cargo trailers and a hydraulic dump trailer. I’m constantly amazed at the cheap wiring, it’s all waiting to fail.
Thank you for your video!
When I pass wires through a frame, I drill a larger hole and insert a piece of rubber tube tpo form a grommet. it pays off over time.
Man thank you so much. I’ve been dealing with no breaks on my single axel dump trailer. I checked for power coming to the rear with a volt meter and was getting 12.0. I cut one of the Scott factory connectors out and used a regular one and bam I have breaks again!
This was good to show how issues occur and how a quick patch can be done.
This is not repaired.
A complete rewire is needed unless you like endless wiring issues.
Nathan! I started watching this video because I just bought a homemade trailer and the brakes were cut, so I'm gleaning information on how to successfully fix them. As soon as the video started and I heard you talking, I realized that you are the same Nathan from one of my favorite MRE review videos! It's great to put a face to a voice finally. Thanks for the help and great videos!
My brother gave me a trailer. The wiring had so many splices done half assed, I removed all the wiring and started over. NEW everything lights, brakes trailer to vehicle harness and breakaway. It did not cost that much. Well under $200.00. I wont have to worry for awhile.
Dielectric grease in crimp connectors then coat with Liquid tape to seal.
Better to use the crimps with heatshrink ends built in then cover in heatshrink.. Or better yet, solder, wrap w/good tape (or liquid tape), then heatshrink. Also, you should have found the melted wire in the initial inspection :)
WTH?
Shrink OVER tape?
Ridiculous!
@@teejay622 if it works, it is not ridiculous.
I would suggest a complete re-wire including a junction box to clean up the existing wiring. Trailer wiring takes a real beating and needs to be task-specific and of higher quality. One can get creative to get a trailer home, but for the long haul, it's better to do it right. Good luck.
Good tutorial. Though I do take issue with the apparent bias against incandescent bulbs. Incandescent bulbs have worked fine for 100 years, they are simple, proven tech, and replacement bulbs are relatively cheap and easy to find. I can see where if say 25 bulbs were in operation drawing say 15 watts each, that would be a dangerous and problematic overloaded circuit. But with just a handful of bulbs, the switch to LED’s would be expensive and unnecessary.
NEVER ground any trailer through the ball. That's the best way to misdiagnose any trailer wiring issue.
thanks, you gave me steps to figure where my problem might be, and what to look for.
put a 7 way junction box n break away
What if my lights work but not my axle brakes new installation?? Please help
I just want to know what kind of mat you are laying on while working on the rough ground
You rewired harness. Not sure if you opened junction box for wire splitting. But that was my problem.
You have to check everything from Harbor Freight.. I hear you on that one 👍😅😂🤣
What do you hook the two wires coming out of the hubs too. What are the connections for it?
When I'm pulling my trailer it keeps saying trailer connected and trailer disconnected over and over as I'm driving. All the lights work but there is no power at the blue wire which is the brakes. Does anyone know what is wrong?
@Edward Duran Try some dielectric grease on your plug. It is probably just bouncing around.
Wire crimps red,blue ,yellow ones are not made to be taped around for designed to be open at where moisture can escape
wanabe logger ... Then why can you buy them where the covering is shrink wrap?
@@keenanleetodd The heat shrink type have dielectric grease inside to help repel moisture.
What wire is the ground and hot, I o ly have white and black, where do I hook up the blue wire?????
The blue crimp wasn't even a heat shrink version crimp still not water tight lol
Just picked up an old trailer, lights work but.... The trailer brake wires were cut.??? How do I fix that?
Should be called "Half Assed way to wire trailer"
Should not of
Wow this is a great video on what not to do I didn’t realize it so hard to make a great video
Sequoia, sweet. ..and I "understand what your talking about" I own 5 trailers currently the 2 with brakes are around 10 y.o. this video helps. Clear and to the point! Thanks Nate!
You solder the wires before you heat shrink them..
I ran my trailer and failed to connect the Plug to the brakes. My brakes locked and I dragged it a ways before I discovered the problem. I’m worried now I might have compromised my wiring and brakes. How do I check to see if the wiring is good/bad?
he knows very little more than the owner of the tra. .......lol
I was wiring my trailer today started watching this then realized he sound just like the guy from STFN 👀
That was great
great vid thanks
They should be soldered together, it may easily pull out of the heat shrink.
watching this at 3:58 am lol learning does have a time!!
on my trailer I got the whole wire light kit, driver light everything thing is fine but passenger light on turns on but don't blink or flash wen u brake
So is the white wire hot or ground?
I don't have a trailer but it's still interesting
Sir, respectfully, you should have advised the trailer's owner that he really does have a major need to completely re-do his trailer's wiring.
Yes, you helped him a little bit with the "bandaids" that you performed -->, just enough to limp on. However, if he comes to a roadway inspection station, and/or an alert highway patrolman, your friend might have to do some fast talking. Moreover, and just for safety, if your friend is to rely on that trailer, common sense would dictate for a complete wiring overhaul, eliminating this cluster-mess.
Hello, I liked your video. I just completed a tent trailer wire up with electric brakes. The brake controler seems to be working but, when I activate the brakes i do not hear them. I have not road tested it yet, any suggestions on testing if electricity is getting to the brakes? Thanks so much.
Trailer brakes 101? LOL. Should have named the video, "I'm gonna try to figure this shit out."
🤣🤣🤣
Good information.
I'm clicking off ..Soon as he said twist the wires together that was it for me.. You have to solder the wires and use the sealant type heat shrink ..
What brand are those LEDs? I almost bought the LED square ones from Tractor Supply but they don't seem to get the best reviews.
i think i bought those from buchheits , they have a store in herculanium
Don't do close up video if you're going to be starting at your image in the screen... It's distracting... your audience is in the camera lens.
Do not twist wires then cover that up with heat shrink, solder them or get butt connectors, this is VERY WRONG.
That plug cable needs to be replaced. You are way beyond replacement time
You need to change the name of the video please. It indicates you are troubleshooting brakes and in your intro you say rewiring brakes and lights.
Your wiring is atrocious on your trailer. Worst I've ever seen. It's embarrassing putting it on youtube
lol well its not my trailer and I didn't wire it, it seems that 43000 people disagree with you and 10 agree,
He even stated it's not his trailer, that he is fixing it!
Scott Ivey .... He never fixed it. He red greened it.
when you you fix something fix it right should of yanked all that wire out put all new hope your friend didn't pay you
If that's the worst you've ever seen, you don't fix much of anything.
He clearly mentioned that it is not how he would normally do it, as he lacked the supplies.
I gotta ask those of you saying he should have done it better, what is your proper procedure for fixing broken wire?
Most of the time, people who like to talk don't even know how to do anything in the first place.
Keep your day job because you're not qualified to wire a trailer.