The project got bumped done on the priority list for a bit, but now I’m revisiting it. Thank you so much for replying to my Reddit post and providing the world and litematica downloads. These should help me a lot figuring out the blast chamber of mine.
Nice work, thanks for sharing. The main thing I had been wondering about X's design was why he built this "rising staircase" instead of just a single-layer plane using conveyor belts. Would you run into issues due to those being observer based there as well?
The main issue with using piston snakes and blocks streams between pads to keep it in a single plane is that its much less lag efficient. I used the same concept in my first iteration of of a clay farm of a much smaller size than this farm was putting out substantially more lag which translated into a higher mspt and lower frame rate due to pistons constantly firing. Yes you run into issues using observers between pads, but can easily be circumvented with the pre observer smart piston methods, which again, increase lag and lower frames due to inherent lagginess from both pistons and redstone dust. Using the stair step method in this farm (and a future clay farm from me) you not only reduce your lag, but you also ELIMINATE any failures due to clogging INSIDE the farm. Issues can still arise before and after in the block streams, but nothing should EVERY go wrong inside the farm :)
Has there be any tests of this farm on multiplayer? Considering trying it on a Paper server. Would low tps cause any major failings? Increidble video btw, subscribed now and looking forward to your next video.
Shouldn't cause any tps problems :). Go check out my omnifarm video for a much better layout though. If you're worried about the lag that 6 piston conveyors might cause, you can just push the blocks directly up between layers :) just make sure to use the same blast chamber shown here because my new blast chamber doesn't work reliably on paper servers.
This is actually as fast if not faster than spacing them apart, not to mention, much easier to automate. Having the oxidized cut copper slabs between each platform (with at least 4 spaces filled with oxidized between the bottom and return platforms) actually speeds up the checks the game makes for whether or not a block should oxidize. Obviously it would be SUPER slow if you didn't have the oxidized copper between the platforms, and I didn't do very well emphasizing it the vid.
@yellerthc6010 I've subscribed and am keen to see where you go. I think your content quality is good. However, if you grow in channel size it may be a good idea to have a different skin. Keen to see what you make next.
I appreciate the sub! I agree I will have to change my skin eventually, and it was only meant as a place holder until I either made or found a skin I liked. The Kakashi skin and variants of it still to this day are some of the cleaner looking skins, though
its been caressed and i kicked that subscribe button too
The project got bumped done on the priority list for a bit, but now I’m revisiting it. Thank you so much for replying to my Reddit post and providing the world and litematica downloads. These should help me a lot figuring out the blast chamber of mine.
I dont even go on reddit so someone else must've sent ya, but it's appreciated nonetheless!
Great design! 5:49 reminded me of the "16 times the detail" meme xD.
Nice work, thanks for sharing. The main thing I had been wondering about X's design was why he built this "rising staircase" instead of just a single-layer plane using conveyor belts. Would you run into issues due to those being observer based there as well?
The main issue with using piston snakes and blocks streams between pads to keep it in a single plane is that its much less lag efficient. I used the same concept in my first iteration of of a clay farm of a much smaller size than this farm was putting out substantially more lag which translated into a higher mspt and lower frame rate due to pistons constantly firing. Yes you run into issues using observers between pads, but can easily be circumvented with the pre observer smart piston methods, which again, increase lag and lower frames due to inherent lagginess from both pistons and redstone dust. Using the stair step method in this farm (and a future clay farm from me) you not only reduce your lag, but you also ELIMINATE any failures due to clogging INSIDE the farm. Issues can still arise before and after in the block streams, but nothing should EVERY go wrong inside the farm :)
Has there be any tests of this farm on multiplayer? Considering trying it on a Paper server. Would low tps cause any major failings?
Increidble video btw, subscribed now and looking forward to your next video.
Shouldn't cause any tps problems :). Go check out my omnifarm video for a much better layout though. If you're worried about the lag that 6 piston conveyors might cause, you can just push the blocks directly up between layers :) just make sure to use the same blast chamber shown here because my new blast chamber doesn't work reliably on paper servers.
Why are the blocks together instead of spaced apart to increase conversion rate?
This is actually as fast if not faster than spacing them apart, not to mention, much easier to automate. Having the oxidized cut copper slabs between each platform (with at least 4 spaces filled with oxidized between the bottom and return platforms) actually speeds up the checks the game makes for whether or not a block should oxidize. Obviously it would be SUPER slow if you didn't have the oxidized copper between the platforms, and I didn't do very well emphasizing it the vid.
Ethoslab????
I wish... Nah, just a fan of Kakashi
@yellerthc6010 I've subscribed and am keen to see where you go. I think your content quality is good. However, if you grow in channel size it may be a good idea to have a different skin. Keen to see what you make next.
I appreciate the sub! I agree I will have to change my skin eventually, and it was only meant as a place holder until I either made or found a skin I liked. The Kakashi skin and variants of it still to this day are some of the cleaner looking skins, though
Isn't this just Xisumavoids? wdym "I AUTOMATED"
Edit: lmao nevermind forget what i said i didnt start watching the vid
It's all good, I find myself doing the same sometimes :)