That pump was running for a long time with many air bubbles in the input feed line, leading to bad aeration and cavitation and so erosion of the blades in the centrifugal impeller. * At 2:59, that is not the extractor/ puller one uses to pull off the impeller, as it will distort and warp it if it was going to go back into the pump. Those two holes in the impeller are meant to screw two pulling bolts in them and pull on them and push on the shaft. Those two holes are closer to the centre and they will pull the impeller from more solid location without distorting it. * At 8:31 the gap between the impeller and the body of the pump between the input and output separator is too wide, and there will be a cross over loss from the high pressure to the low pressure side rendering the pump inefficient and will lose the head. There should be no gap there for maximum efficiency. At 7:38 the impeller should not be hammered in, as that is too tight, I prefer it to be not tight and the impeller will settle in on the running surfaces on both sides when the last enclosure of the impeller is placed in position.. * At 9:41, that two pin plug should have been cleaned for a better contact. A squirrel cage induction motor takes a starting current of about 3 to 4 times the running current.
Yr video is good and in detail. My 1hp crompton motor pressure is low now since one week. Two yrs back purchased. Servicing done now and seal, capasitor, impeller changed one by one but no pressure improvement. Even mechanic do not understand why is happening like this. No more parts left to change. No leakage & air gap. Can u suggest me on this. This is a mysterious problem and its a challenge to get answer. Awaiting for yr reply.
Thank you Sanjay Kumar Gupta for the video. I have concern for water pump. In our society, my house is at number 7. And only one water line. So first 6 house run their motors and get the water but I am unable to get water. Currently I am using 1hp Hitesh Water Pump. Can you help solving the problem?
Iska shi polar btaye. Konsa le taking date tede mede ya crack nhi ho jroor btaye konsa shi hoga mere pas bi khatan 0.5 HP ka yhi mortar he seal Chang krni he
Sir mere pass Venture Water pump machine hai 0.5 HP Wala To Muje Us machine Mai Zyada Pressure Chahiye Taki Mera 2 Floor ka building Hai to To 1000Ltr Ke Do Tank Hai to Muje US mai Zyada Presure Padna hai To Zyada Presure Wala machine Chahiye to Uske Liye Kya karna Padega
Hlo sir mere paas centrifugal monoblock pump h 0.5hp aise pani theek nikal rhi h, but tanki mei pani chadao toh 1-2 minutes k baad pani chadana bnd kr deti h kya kru koi suggestion do .......
While purchasing new one all dimensions of impeller should identical otherwise it creates problem. Many time for new person difficult to get correct substitute. Shop keeper is generally not replace if some difference is there and for customer no use . Mechanic they can use somewhere to other customer.
Sir mene abhi pani ki motor ki nai winding dalwai he...motor chalu krne k aad usme se धूँआ aata he or motor ki body bhi jyada garm ho rahi he..kya karan he iska..plz answer me
👍👍👍 3 साल पहले मैंने इंपैलर निकालने की कोशिश की थी लेकिन मेरे पास पुल्लर नहीं था तो इस वजह से मेरा इंपैलर भी खराब हो गया था क्या इसे निकालने का कोई देसी जुगाड़ भी है तो कृपया आप बताएं जिससे इमरजेंसी में इंपैलर को बिना पुल्लर के निकाल सकें।
Look for the pump curve if it is available for that pump and check if you can add bigger impeller in that pump which will give you higher head at the required flow rate.
सर मेरे वाटर पंप में नया empelar डालने के बाद जहां मोटर लगी है वही प्रेशर ठीक है लेकिन जब हम प्लास्टिक की 100 मीटर hard पाइप में उसको जोड़ते हैं तो वह पानी हार्ड वाली पाइप में ऊपर नहीं चढ़ता है क्या कारण हो सकता है सर
Sir mai impailer aur water sheal dono change kiya per tab bhi pani kam de rha hai kya karna hoga Aur bhi koi tarika hai pani jada badhane ka to bataiye jaldi sir please
Very nice video, both part, with this video i have repaired (complete shaft , bearing , seal etc) monoblock pump. I saved money. Thanks. One request to you. If possible, can you please make a video on repairing Arise Shallow Max ll - 1hp same like this with complete detail.
भाई आपने इम्पेलर को सेट करने की सही जानकारी दी है जिससे पम्प वाटर प्रेसर अधितम देगा ये मुझे विश्वास हो गया है।
धन्यवाद 🙏🙏
🌹 Share this video
वीडियो मस्त लगा मेरे को
Thanks
नमस्कार सर जी आप ने जो दिखाया हैं बिल्कुल सही दिखाया हैं
Thanks
That pump was running for a long time with many air bubbles in the input feed line, leading to bad aeration and cavitation and so erosion of the blades in the centrifugal impeller.
* At 2:59, that is not the extractor/ puller one uses to pull off the impeller, as it will distort and warp it if it was going to go back into the pump. Those two holes in the impeller are meant to screw two pulling bolts in them and pull on them and push on the shaft. Those two holes are closer to the centre and they will pull the impeller from more solid location without distorting it.
* At 8:31 the gap between the impeller and the body of the pump between the input and output separator is too wide, and there will be a cross over loss from the high pressure to the low pressure side rendering the pump inefficient and will lose the head. There should be no gap there for maximum efficiency.
At 7:38 the impeller should not be hammered in, as that is too tight, I prefer it to be not tight and the impeller will settle in on the running surfaces on both sides when the last enclosure of the impeller is placed in position..
* At 9:41, that two pin plug should have been cleaned for a better contact. A squirrel cage induction motor takes a starting current of about 3 to 4 times the running current.
You are a genius.....I loved your detailing and I too agree with all your points !!
thanzzz u sir aap k saare video ache h sab laga bhi h
Bohot tej dimag lagate ho sir aap nahi to ye ampelar leth machine ke Bina nahi khulta thanks sir
Aap mere teacher hai sir...nice
Namaste Sir very helpful video thank you.
आप इस Video को अपने सभी दोस्तों और रिश्तेदारों को Share जरूर करें
Good information video...👌👌 Thanq very much sir...👍👍
Most welcome
🌹Share this Video
Good Sanju brother Thank you excellent video.
[PAKISTAN]
Always welcome
Bahut hi saral tarike se ap bta diye
Excellant demonstration. Love from Pakistan.
Ok
J
Valeu amigo, vídeo muito bom.
C'est simple et profitable, merci.
Thanks so much sir good bless you
thankyou very much good topic👌👌👌👌👌👌👌👌👌👌👌
Maine apki all video dekhte hai apki video dekh kor maine ek fan ;ek motor ka problem solv kiya hay.
very good
Thanks you sir. 0.5hp monoblock pump wineding video banao na please sir.🙏🙏🙏
bhai sab excellent demonstration 🤗👌👌👌👌👌
Thanks
Nice video, how to increase water pressure.
Good Explanation
Thanks
Sir apka video bahut achha lagtahe
Nice
Very very excellent
Yr video is good and in detail. My 1hp crompton motor pressure is low now since one week. Two yrs back purchased. Servicing done now and seal, capasitor, impeller changed one by one but no pressure improvement. Even mechanic do not understand why is happening like this. No more parts left to change. No leakage & air gap. Can u suggest me on this. This is a mysterious problem and its a challenge to get answer. Awaiting for yr reply.
Change the NRV (non return valve)
thanks sir very helpful video👌
Thank you Sanjay Kumar Gupta for the video. I have concern for water pump. In our society, my house is at number 7. And only one water line. So first 6 house run their motors and get the water but I am unable to get water. Currently I am using 1hp Hitesh Water Pump. Can you help solving the problem?
Switch to Crompton Mini Master 1
Kya water pump ko sewage pump mein convert kiya ja sakta hai.
Thanks
Best video
Please next video
Ok thanks
Ektham badiyaaaa👍👍👍
Thanks
धन्यबाद सर
Very good 👍. Why impeller is getting demedg without touching back side or front side. Please answer
THANKS G YOUR ALL video s Ajmal s from TAMIL NADU
M
Iska shi polar btaye. Konsa le taking date tede mede ya crack nhi ho jroor btaye konsa shi hoga mere pas bi khatan 0.5 HP ka yhi mortar he seal Chang krni he
Very nice video thank you sir
आप इस Video को अपने सभी दोस्तों और रिश्तेदारों को Share जरूर करें
Sir 0.5 motor winding achi hai bearing bhi thik hai fhir bhi motor garam hoti hai aur no load current 7amp leti hai kya karan ho sakta hai
बहत ही अच्छा विडियो बनाए आपने, दो legs के puller से impeller खोलने से केया impeller के दांत खराब हो सकता है ?
हाँ , खराब हो सकता है , इसलिए मैं बता चुका हूँ कि ये impeller पूरी तरह से खराब है इसलिए मैं इस puller से निकाल रहा हूँ
Surajit Das ppp
kase nikale ampurar
Nice feeling of imppular
Sir mere pass Venture Water pump machine hai 0.5 HP Wala To Muje Us machine Mai Zyada Pressure Chahiye Taki Mera 2 Floor ka building Hai to To 1000Ltr Ke Do Tank Hai to Muje US mai Zyada Presure Padna hai To Zyada Presure Wala machine Chahiye to Uske Liye Kya karna Padega
Snju bhai apki aawaz bhut achhi h
Hlo sir mere paas centrifugal monoblock pump h 0.5hp aise pani theek nikal rhi h, but tanki mei pani chadao toh 1-2 minutes k baad pani chadana bnd kr deti h kya kru koi suggestion do .......
While purchasing new one all dimensions of impeller should identical otherwise it creates problem. Many time for new person difficult to get correct substitute. Shop keeper is generally not replace if some difference is there and for customer no use . Mechanic they can use somewhere to other customer.
Sir impeller fit krne k Bad line ment thik nahi hai kya kre
Esi vedio like nehin subscribe Bhi banta hai
🌹 आप इस Video को Share जरूर करें
Nice video sir
Thanks
Very useful Sir thanks
shivaraju 200011
Mere pass ak motor hai uska pani Ka pressure Na ke barabar hai uska hal batawe.
Water pump पर मेरे कुछ और भी video है। आप मेरे channel पर जाकर उन सभी video को देखे। शायद आपका काम हो जाए।
Dada isko blade anticlockwise no clockwise ghumta hai please puchiye.
Nice sir✌🏻✌🏻✌🏻
आप इस Video को अपने दोस्तों और रिश्तेदारों को Share जरूर करें।
Bhut acha video sir
Thanks
बहुत लम्बी वीडियो बनाया है ।
How much the price of this impeller?
Sir mene abhi pani ki motor ki nai winding dalwai he...motor chalu krne k aad usme se धूँआ aata he or motor ki body bhi jyada garm ho rahi he..kya karan he iska..plz answer me
Mere paas kirloskar ka 0.5HP ka motor hai use chalane ke turat baad garam hokar band ho jata hai or pani bhi kam deta hai... Kya karein ?
Thank you 🙏
🌹 Share this Video
अगर इमप्लेयर उल्टा बेड़ायेंगे तो क्या पानी के प्रेशर फर्क पड़ेगा ?
Can you tell me what is check valve in a pump.
हाफ एच पी का मोटर है 8:00 का कैपिटल लगा है 10 का लगाने से क्या होगा पानी नहीं ऊठा पा राह है
Very good video sir I
Thanks
Aap Se JNnna Kahta Hun ki Aap Tul Pump Ka Winding Hath Se KAise Kurnga Achhi Tarah Se Tar Turn Pitch Me Kase Dalna Batane ka kirpa Karyn Danywad
Cancil
Good job videos
Thanks 🌹 Share this video
best video sir
Thanks
Very nice sir
Thanks
Very good video
Thanks
👍👍👍
3 साल पहले मैंने इंपैलर निकालने की कोशिश की थी लेकिन मेरे पास पुल्लर नहीं था तो इस वजह से मेरा इंपैलर भी खराब हो गया था क्या इसे निकालने का कोई देसी जुगाड़ भी है तो कृपया आप बताएं जिससे इमरजेंसी में इंपैलर को बिना पुल्लर के निकाल सकें।
Gupta ji water seal kitne type ke hote hai .1hp aur 0.5hp pump ko ek type ki water seal lagti hai Kya
शुक्रियाआपका ये वीडियो भाहुथ अच्चाहाई
The water pressure on the ground floor is fine, but it reduces by half on the first floor. Any suggestions?
Look for the pump curve if it is available for that pump and check if you can add bigger impeller in that pump which will give you higher head at the required flow rate.
ধন্যবাদ ভাই আপনাকে
most welcome
सर मेरे वाटर पंप में नया empelar डालने के बाद जहां मोटर लगी है वही प्रेशर ठीक है लेकिन जब हम प्लास्टिक की 100 मीटर hard पाइप में उसको जोड़ते हैं तो वह पानी हार्ड वाली पाइप में ऊपर नहीं चढ़ता है क्या कारण हो सकता है सर
My water pump crompton mini masterplus 1HP not proper water pressure plz advise me repair or change motor
Thanks vidio
🌹 आप इस Video को Share जरूर करें
Nice video sir..
Thanks
Sir mai impailer aur water sheal dono change kiya per tab bhi pani kam de rha hai kya karna hoga
Aur bhi koi tarika hai pani jada badhane ka to bataiye jaldi sir please
Motor awaz Karti h ahhi empilar change Kiya h १५ din पाहिले ??
Motor pani na uthanay ki problem ispe video banao
vry good sir...
Thanks
Sir.. मोटर का capaciter कब change करणा पडता है. मतलब के कोणसा fault आणे पे समझे की capaciter बदलना है.. इस वजह भी तो प्रेशर कम दे सकती ना.. Pls बतायें
Haat se guhmane pe chale tab
Sir mujhe 1.5 inch motor ka impellor khol ke dikhaiyea na please mujhe aapka video bahut pasand aaya
मौका मिलेगा तो video बना दूँगा
Sir 1.5 inch 40mm pipe Wala motor ka impeller kholne Wala video banayea na
Thank you sir
Welcome
Sir.mera.kilokar.moter.kds(12).ka. hi. Kya. Kds(13).ka.lmpeler.aega
जल्दी जल्दी बताईये. 😀😀😀
Nice video
सर नमस्कार ।।। टेप नल और 0 मोटर और टुलू पंप के नाम से बोलते हैं birra me
Thanx🙏🙏🙏🙏
Most welcome
Good Video
Thanks for the visit
Acha h sir
keep watching
Sir gharelu motor ki winding jal jaye to dobara winding kaise krenge
Thanku bhi
always welcome
Nice sir
Keep watching
Bhaya mujhe 1 karn ka hal btaye motar haph ranch eanch kahai motar hit horha hai motar ko vendig kiye hai Kiana bhi malum kiya hai patanhilaga hai
Kya water pump ki suction power jyada ki jasakti hai kya
Very good
Impeller change karne ke baad Moter head me se air leakage ho rahi hai kay kare
Thank you
You're welcome
🌹 Share this video
Ak paip me teen kanekshan hai aur agar do admi ke nalke chlu hai totishre nalke me moter se pani nhi ataa upay batay
impeller rod ke sath loose fit hai, kya karna hoga?
Good explanation. TNQ
Gjb sir
Very nice video, both part, with this video i have repaired (complete shaft , bearing , seal etc) monoblock pump. I saved money. Thanks.
One request to you.
If possible, can you please make a video on repairing Arise Shallow Max ll - 1hp same like this with complete detail.
Amplifire ka daam kitna padega