Brother 8810dw replacing the fuser

Could be similar to 8710dw and 8910dw

[@KMayflower]

Two 50 year old women used this video to install a new fuser on a Brother MFC-8710DW in 20 minutes with just a screw driver!!Thank you for the great video, we couldn't have done it without it!!

[@angrycatowner]

How many 50 year old women does it take to replace parts on a MFC? Don't put them down, they are not stupid.

[@stevesikora]

Thanks for the step-by-step demonstration of both disassembly and reassembly. It helped me get over a couple of areas where the parts seemed to be too tight, so I thought I was doing something wrong. I changed the fuser unit since the print coming out blurry and would jam sometimes. Everything works well now and the print is crisp like before.

[@yichunzeeck7038]

I am have still using ur video after all these years. Please keep it on UA-cam. Thank you

[@jaredsavino5129]

Thanks for the video! This video also applies to the Brother MFC-8950DW. Just followed this video while replacing the fuser on my 8950.

[@TheRealLaughingGravy]

Thanks so much. I just did this with an MFC-8910DW, and the parts and procedure are the same. The parts came out easily but went back in with much more difficulty because everything is black inside. It was very helpful to have this video to refer to.

[@jcolonjr]

Invaluable video! Our fuser has needed replacing three times (the ONLY thing that has gone bad on this printer) and all three times I've used this video. THANK YOU for recording and sharing!UPDATE: Now it's been 4 times this video has helped! This Brother printer has outworked our past Kyocera & Xerox!

[@bens4life]

how do you know when it has gone bad? What is the exact problem?

[@sharond2422]

Thank you! I did it! Saved myself big bucks on a nearly new printer with fuser issues.

[@lHurtYourFeeIings]

Damn saved my printer

[@sherridyer1402]

You are my hero. Saved me a ton of $$ and I have my printer working perfectly again. Many thanks.

[@Ilovenygal]

Thanks for taking the time to post this. I was able to replace my fuser with no problem! :)

[@paulv2664]

Thanks for posting this. Fixed it myself no problem with your video!

[@SPARTANsui1]

Video was very helpful, thanks for taking the time to make it.

[@SainatoChiropractic]

Thanks for the video - replaced fuser for MFC-88719DW - thank you again for posting

[@SainatoChiropractic]

sorry MFC-8710DW

[@grizzlypeg]

Very helpful video. Thanks!

[@brianbailey1505]

Thank you so much for recording this!

[@gmm1878]

UENOS DIAS OJALA ME PUEDAS AYUDAR TENGO MFC 8950 IGUAL COMO LA DEL VIDEO. EL DETALLE QUE FUNCIONABA BIEN Y DE PRONTO ME DICE QUE CAMBIE EL TONER. ENTONCES YA SE LO CAMBIE Y EL MENSAJE ME SIGUE APARECIENDO , YA CAMBIE COMO 3 TONER NUEVOS DIFERENTES YA HASTA CAMBIE EL DRUMMM COMPLETO Y AUN ME SIGUE APARECIENDO EL MENSAJE ME DICE " CAMBIE EL TONER AQUE SE DEBE O CUAL ERROR PODRIA HACER AYUDAME

[@josueparra9495]

Donde consigo la guia de plastico blanco que quitas antes de sacar el fuser que esta a tu lado izquierdo se me quebro

[@garlati]

Muchas gracias!!! Excelente el vídeo!

[@ramonperera6218]

I need to get to the power supply board on an MCF L2700DW. It does not turn on after a lightning. I do not know how to open the panels to get there. Please help. Thanks in advance,
Ramon Perera.

[@Krisstofers]

Oooh! I like his watch!

[@johntjarks329]

Awesome Video Thanks so much!!!!!!!!!

[@popsy3k]

just open and close the front door concerning the nylon latch, and the fuser cover has 2 notches .........

[@davidlis6709]

Good video.

[@emilarnest6702]

thanks too much it very nice it is help me

[@paismast]

gracias me sirvio de mucho

[@user-ww8lo4kq5w]

There's a jammed paper in the rear off mfc8910dw help me remove it

[@christopherdouglas4375]

I busted the little spring with my ham fists will it still work or is that a ground?

[@siggymartin]

Couple little springs. Yes, a ground for that skinny one. Did it still work?

[@tundratekk]

Where can i order a fuser for my Brother 8710dw unit?

[@KIkeAutoElectric]

good, I liked the video but I ask you, Where can I buy that part for my Printer?

[@Mike_Jones281]

Amazon

[@noyempleo]

Assemble replacing?

[@davidlyles9154]

How do you reset fuser counter to get rid if fuser error in display

[@brentee]

That's what I'm looking for too.

[@briangray5921]

Hold 3 and 9 keys together to get to reset menu

[@williamsturgeon4271]

why replace a junky fuser with another junky fuser? they all melt down with moderate use. no support from brother. buy hp.

[@CubanB1978]

all fusers wear out. they are designed to do so.

[@popsy3k]

ok, ...rich boy ,thats funny, Brothers support team answers my Emails

[@johnrichardson4963]

Switched to Brother from HP. 100% of the functionality with 75% of the headaches. Plus it's cheaper all around.

[@dottorb7054]

Same. Used to be HP only but their support was so horrible (and rude and obnoxious) that I switched to Brothers. Man, the things are workhorses!

[@luvpoems4u]

Great video! I removed (on the left) the little white plastic cam or whatever it's called, and the nipple or tit is broken off...I have no ideal how to find this part!!! HELP! plzzzz...If I had a part number maybe I could find it. Thanks for your help! (Brother model# MFC-8910DW)

[@crystinaperera9726]

I have same problem. Do know the part number

[@lazaronieto85]

This video would be way better with some explanation of what you are doing and without that horrible music

[@embroderyknittingscreenpri7349]

why replace a junky fuser with another junky fuser? they all melt down with moderate use. no support from brother. buy hp. i agree 100%

[@TheRealLaughingGravy]

Is there an echo in here?

[@siggymartin]

Mine’s original and 10 years old. Patience, 91% alcohol or butane, and G8010 grease and mine still works!