For the dreaded solid green light, please try this: 1) Reflash or downgrade the firmware for the transmitter. 2) Put the transmitter into bind mode. 3) When you power the Rx (without the bind button pressed), does the LED turn red color? If so, then the Tx should ask to update and proceed through.
Hi, mine have solid green light since begining, tried your advice to downgrade is done but nothing happened, it just still solid after pressing the bind button after power up the rx. downgraded 6.06 to 4.1. any advise?
Nice video, I have done all you said, only mine is not going in to a rapid flash again for the second time, but turns solid green after the double green flash :-( Any advice
Hi, I do the whole process like you do, only that when I unplug the quad and plug it back in, it loses the bind, and every time I have to redo the same operation, has this ever happened to you? How can I fix?
A few things to try to rule out a few things otherwise your receiver is broken/defective and needs to be replaced by TBS Support: 1) Have you tried different firmware and downgrading? The latest one that has encryption has caused some issues for people. 2) Power up the receiver first and then the transmitter first to establish a bind?
@@OfficialMatrixFPV I did many tests, I followed various guides including yours but all without success, on the rx it doesn't let me downgrade, on the tx yes, I tried but nothing happens, I tried to bind by turning on the rx first and then the tx, then in reverse, but every time I disconnect and reconnect the battery it loses the bind, in fact I'm sending it back, because something like this has never happened to me until today, and the only tool to restore the rx is a tbs core pro which costs around 40-50$
Mine won't bind, TBS Tango 2 says: Reload Crossfire FW in agent X. But I just updated it. Receiver just go red after blinking fast, also Agent X app won't read receiver, neither the Transmitter. So I can't update it
Greetings I have a question. Tbs nano is connected for my diversity controller, module and receiver are glowing green but no response. Do I need to update the tbs xlite module for it to work or should I update it to my remote? control version 2.2 opetx
My receiver doesn't stop to blink fast after pressing the button for the second time. The green light even blinks rapid when I don't press the button and connect the battery. All of that happened after the first bind failed in updating. :/
After the update is 100% my rx goes again in rapid green flashing mode and tx shows binding in progress, no matter how many times I repeat the process it ends in rapid green flashing state 😢 Please help.
I know this is an older video. I followed the steps and everything went as it shows in your video. Bound up and works perfectly... but when I unplug the battery and then wait and go to re-connect a battery it is just flashing again and I have to go thru process again... Kind of lost in where to go from here... Anyone have any suggestions? Thanks
Have you been able to downgrade and try other firmware, I would try different types to see if binding is stable? It's rare that binding has issues with TBS - check with what others might be saying about the latest FW on the TBS Facebook group. You can definitely get more support by asking there or opening up a ticket with their support - they are fantastic and will do their best to make things right.
@@OfficialMatrixFPV I ordered some new Nano Rx's but haven't gotten them yet. So I went to a buddies house tonight and borrowed his spare Nano rx and it bounded up perfectly and is holding bind as it should. 👍
5. Release the bind button when green led flashes rapidly For me, after I press the LED for about 5-7 seconds, it becomes solid green. And the transmitter is unable to detect it.
whycaee you holding the button down. you don't have to do that with crossfire . you don't have Nichols the button while powering to get it to bind. it will do it automatically and update the rx
Led turned off after emergency procedure, no red light. Tried downgrading micro tx to 2.42 cause that the lower i can go on tbs agent and still nothing. Any other solution.
That is an odd issue and I haven’t seen this before. Would you please post this in the TBS Lounge Fb page or create a support ticket at TBS? I’d definitely like to know more.
@@nicklessticksfpv Thanks! I will keep an eye on this on Fb, if there is a potential solution I can add it to the description/comments as that was a similar issue with the dreaded solid green light.
@@OfficialMatrixFPV i think i had the same problems, did the normal thing, bind new RX and then a pop says about updating, so do that, it does its thing, at part of rebooting to then rebind after flashing, both LEDS are off, i left mine for a good five mins, then ended up pulling the power and back in again, it will not bind and will not go into recovery mode so i can reflash the thing, i made a ticket with TBS and they just ended up sending another one, had the thing in a draw for six plus months so it was nice of them to sort me out, but like to know if i can fix the broken one instead of binning it, this is what mine does ua-cam.com/video/oLBaw17eyjU/v-deo.html
@@andrewmaudsley7692 that is a definitely a weird issue as the red LED doesn’t show up. Also noticed that the blinking green LED was quite erratic. At least they sent you another one. I’m thinking it’s related to actual HW issue. A way to see if you could try to fix is to connect the TBS Core Pro unit via BST and reflash the FW manually from their Agent X software from the computer.
my received after relase the button the second time, all led power off and procedure don't done or remain fixed green, but radio not bind. I've try procedure many time with same failed result, have you any other idea to reset rx? thanks
DareDevil_ FPV I’m guessing the a solid green light the process is different from what I found online... Which Tx firmware version are you running? I would try a lower version and put it into bind mode. When you power the Rx (without the bind button pressed), does the LED turn red color? If so, then the Tx should ask to update and proceed through.
@@OfficialMatrixFPV hi I am having an issue with multiple recievers where they flash red after i start the binding process on the tx. When the tx is not powered on, and quad gets booted, my rx will flash slowly green. But then when I turn on the tx it will go to a red flashing. The tx does not prompt the "update firmware" anymore. I have tried a bunch of button presses, downgrade of firmware to all kinds of version on the tx, but with no change. Would you happen to have any suggestions as to what I can try to get it working again?
Souldk86 Which firmwares have you tried? I was digging around online...try firmware version v2.25 beta for the transmitter. 1. Switch on the TX and enable bind Mode 2. Power the Rx WITHOUT pressing the bind button - the LED will become red 3. TX should ask you for updating the Rx 4. If this works, bind the other receivers and then update the Tx to the latest FW 4.xx and the proceed with normal bind process.
I’m not familiar with an orange light LED color per their manual. I would factory reset and try the binding again. Emergency update procedure is done on the receiver level, the transmitter will know how to bind from there.
@@earlybirdflights9884 Great to hear that. Would you mind sharing how you resolved it so it can help new viewers? I will add it to the stickied comment and credit you.
I just pluged the usb lead in and used tbs agent x , the orange light started flashing as soon as I loadeed the app. it flashed for about 30seconds and was done. cheers.
Hi! Is the beeping coming from the radio or the quadcopter? That might be a completely different thing as you can still have Crossfire bound without the radio on if you have it module powered with external power (ie USB).
@@OfficialMatrixFPV Hi, yes the beeping is from the radio. Soon as the crossfire module and receiver go green the taranis starts beeping. Any idea? Thanks.
@@Kenny-lq1fz Which Taranis model? I saw beeping could be related to low supply voltage to the module or something with the baudrate if using the older QX7...
@@Kenny-lq1fz That's definitely odd as my previous radio was the X9D Plus. I would try updating to new OpenTx version if you have not. In this video, I am running v2.3.9 (June 14, 2020) release. Your Crossfire binding and settings are saved in the transmitter module and not in the radio as an FYI.
You might not ever have that issue if you power the rx first and then press the bind button. Don’t hold the bind button as you power up the rx. I’m pretty sure you should never do that.
It’s barely visible, but you bring up a good point and noticed it after the video was shot. Wasn’t able to reshoot since my other receivers don’t have this issue.
![☀ Навороченный нано приемник + маяк от ТБС. Для серьезных парней. [Crossfire Diversity Nano RX]](http://i.ytimg.com/vi/hj1xBDP8UYY/mqdefault.jpg)
![☀ Навороченный нано приемник + маяк от ТБС. Для серьезных парней. [Crossfire Diversity Nano RX]](/img/tr.png)
For the dreaded solid green light, please try this:
1) Reflash or downgrade the firmware for the transmitter.
2) Put the transmitter into bind mode.
3) When you power the Rx (without the bind button pressed), does the LED turn red color?
If so, then the Tx should ask to update and proceed through.
Hi, mine have solid green light since begining, tried your advice to downgrade is done but nothing happened, it just still solid after pressing the bind button after power up the rx. downgraded 6.06 to 4.1. any advise?
What if TX dont ask to update?
@Seii-FPV realized that my receiver has little fracture on CPU, kinda not repairable 😅
20$ got loss ☹️
Spend two days trying to figure out why my receiver wouobind and update. This video for me up and running. Thanks 🙏
I was struggling with this issue and this video help me, thanks so much
your video saved me my transmitter, i would have smashed it to the wall. Bless you mate
I am so so grateful! You helped me so so much, can not even describe it! You are a true legend in my eyes :) The method 100% works!
Thanks and glad I was able to help you. Time to send it!
Nice video, I have done all you said, only mine is not going in to a rapid flash again for the second time, but turns solid green after the double green flash :-(
Any advice
It works holding the bind button
Thank you so much. I ran into this problem and this fixed it. Your my hero.
I get my drone to bind and update but once I swap battery the receiver gets unbind and starts flashing fast. You think this would fix it 🤔
Thank you 🏅
Hi, I do the whole process like you do, only that when I unplug the quad and plug it back in, it loses the bind, and every time I have to redo the same operation, has this ever happened to you? How can I fix?
A few things to try to rule out a few things otherwise your receiver is broken/defective and needs to be replaced by TBS Support:
1) Have you tried different firmware and downgrading? The latest one that has encryption has caused some issues for people.
2) Power up the receiver first and then the transmitter first to establish a bind?
@@OfficialMatrixFPV I did many tests, I followed various guides including yours but all without success, on the rx it doesn't let me downgrade, on the tx yes, I tried but nothing happens, I tried to bind by turning on the rx first and then the tx, then in reverse, but every time I disconnect and reconnect the battery it loses the bind, in fact I'm sending it back, because something like this has never happened to me until today, and the only tool to restore the rx is a tbs core pro which costs around 40-50$
Thank you man, my tbs is working :)
Mine won't bind, TBS Tango 2 says: Reload Crossfire FW in agent X. But I just updated it. Receiver just go red after blinking fast, also Agent X app won't read receiver, neither the Transmitter. So I can't update it
how you sorted this praoblem , i have today same red light and no update not show tango 2 ?
to 2min 08sek all good done same , but after 2min 08sek remote tango 2 not show any update , help ?
WOW ,,, man you have a very nice and cool stuff ,,, I like it.
Thank you for keeping simple
I got mine to go through that whole process and then I was finally bound but then when I went to arm it kept going in and out
Greetings
I have a question.
Tbs nano is connected for my diversity controller, module and receiver are glowing green but no response.
Do I need to update the tbs xlite module for it to work or should I update it to my remote?
control version 2.2 opetx
My transmitter doesn’t flash when turning on what should i do?
yes that what happen flash green very helpful thanks
My receiver doesn't stop to blink fast after pressing the button for the second time. The green light even blinks rapid when I don't press the button and connect the battery. All of that happened after the first bind failed in updating. :/
did you fix it? 😭
After the update is 100% my rx goes again in rapid green flashing mode and tx shows binding in progress, no matter how many times I repeat the process it ends in rapid green flashing state 😢 Please help.
Does this work if the receiver light is blinking slow
I know this is an older video. I followed the steps and everything went as it shows in your video. Bound up and works perfectly... but when I unplug the battery and then wait and go to re-connect a battery it is just flashing again and I have to go thru process again... Kind of lost in where to go from here... Anyone have any suggestions? Thanks
Have you been able to downgrade and try other firmware, I would try different types to see if binding is stable? It's rare that binding has issues with TBS - check with what others might be saying about the latest FW on the TBS Facebook group. You can definitely get more support by asking there or opening up a ticket with their support - they are fantastic and will do their best to make things right.
@@OfficialMatrixFPV I ordered some new Nano Rx's but haven't gotten them yet. So I went to a buddies house tonight and borrowed his spare Nano rx and it bounded up perfectly and is holding bind as it should. 👍
@@P.G._FPV That seems like your Rx is faulty. You might be able to TBS to replace it free of charge.
@@OfficialMatrixFPV it was the Rx. Actually both Rx's I had were bad... what's the odds of that. LOL
@@P.G._FPV Yikes! That is pretty rare.
Thank you!
My module stays blue is this a problem
5. Release the bind button when green led flashes rapidly
For me, after I press the LED for about 5-7 seconds, it becomes solid green. And the transmitter is unable to detect it.
what if there's no light at all? yesterday I managed to bind it though, tried to fly and wouldn't bind :((((
whycaee you holding the button down. you don't have to do that with crossfire . you don't have Nichols the button while powering to get it to bind. it will do it automatically and update the rx
Ty sir
Thanks it fixed it!
Thanks, the way works
Thank you so much this worked
Led turned off after emergency procedure, no red light. Tried downgrading micro tx to 2.42 cause that the lower i can go on tbs agent and still nothing. Any other solution.
That is an odd issue and I haven’t seen this before. Would you please post this in the TBS Lounge Fb page or create a support ticket at TBS? I’d definitely like to know more.
@@OfficialMatrixFPV i've done it. On Facebook and a ticket to tbs.
@@nicklessticksfpv Thanks! I will keep an eye on this on Fb, if there is a potential solution I can add it to the description/comments as that was a similar issue with the dreaded solid green light.
@@OfficialMatrixFPV i think i had the same problems, did the normal thing, bind new RX and then a pop says about updating, so do that, it does its thing, at part of rebooting to then rebind after flashing, both LEDS are off, i left mine for a good five mins, then ended up pulling the power and back in again, it will not bind and will not go into recovery mode so i can reflash the thing, i made a ticket with TBS and they just ended up sending another one, had the thing in a draw for six plus months so it was nice of them to sort me out, but like to know if i can fix the broken one instead of binning it, this is what mine does
ua-cam.com/video/oLBaw17eyjU/v-deo.html
@@andrewmaudsley7692 that is a definitely a weird issue as the red LED doesn’t show up. Also noticed that the blinking green LED was quite erratic. At least they sent you another one.
I’m thinking it’s related to actual HW issue. A way to see if you could try to fix is to connect the TBS Core Pro unit via BST and reflash the FW manually from their Agent X software from the computer.
my received after relase the button the second time, all led power off and procedure don't done or remain fixed green, but radio not bind. I've try procedure many time with same failed result, have you any other idea to reset rx? thanks
MerkuFPV Does the receiver turn green or red when you power on the quad?
DareDevil_ FPV I’m guessing the a solid green light the process is different from what I found online...
Which Tx firmware version are you running? I would try a lower version and put it into bind mode.
When you power the Rx (without the bind button pressed), does the LED turn red color? If so, then the Tx should ask to update and proceed through.
@@OfficialMatrixFPV hi I am having an issue with multiple recievers where they flash red after i start the binding process on the tx. When the tx is not powered on, and quad gets booted, my rx will flash slowly green. But then when I turn on the tx it will go to a red flashing. The tx does not prompt the "update firmware" anymore. I have tried a bunch of button presses, downgrade of firmware to all kinds of version on the tx, but with no change. Would you happen to have any suggestions as to what I can try to get it working again?
Souldk86 Which firmwares have you tried? I was digging around online...try firmware version v2.25 beta for the transmitter.
1. Switch on the TX and enable bind Mode
2. Power the Rx WITHOUT pressing the bind button - the LED will become red
3. TX should ask you for updating the Rx
4. If this works, bind the other receivers and then update the Tx to the latest FW 4.xx and the proceed with normal bind process.
ok just tried this and now when I turn on my radiomaster I am not getting an orange light on my tbs module. no light at all. any help please
I’m not familiar with an orange light LED color per their manual. I would factory reset and try the binding again. Emergency update procedure is done on the receiver level, the transmitter will know how to bind from there.
got it sorted thanks ,
@@earlybirdflights9884 Great to hear that. Would you mind sharing how you resolved it so it can help new viewers? I will add it to the stickied comment and credit you.
I just pluged the usb lead in and used tbs agent x , the orange light started flashing as soon as I loadeed the app. it flashed for about 30seconds and was done. cheers.
Hi, I have done this but as soon as it binds my taranis starts beeping constantly. Any ideas what's wrong? Thanks.
Hi! Is the beeping coming from the radio or the quadcopter? That might be a completely different thing as you can still have Crossfire bound without the radio on if you have it module powered with external power (ie USB).
@@OfficialMatrixFPV Hi, yes the beeping is from the radio. Soon as the crossfire module and receiver go green the taranis starts beeping. Any idea? Thanks.
@@Kenny-lq1fz Which Taranis model? I saw beeping could be related to low supply voltage to the module or something with the baudrate if using the older QX7...
@@OfficialMatrixFPV hi, its the x9 plus but it is a few years old.
@@Kenny-lq1fz That's definitely odd as my previous radio was the X9D Plus. I would try updating to new OpenTx version if you have not. In this video, I am running v2.3.9 (June 14, 2020) release.
Your Crossfire binding and settings are saved in the transmitter module and not in the radio as an FYI.
Very good 😂 problème 8 days not bind
Lo intentó tngo mismo problema
still not work, still green flash rapidly :(
That isn't good. Did you get to the double blinking green flashing?
Which FW are you running on the Tx?
@@OfficialMatrixFPV I have double blinking green flashing
oh hey lol I commented before I watched the vide. it worked!
@@matthewarchibald5118 No worries, glad it worked out for you - time to send it!
i would kiss you if you were here thank you so much lol
You might not ever have that issue if you power the rx first and then press the bind button. Don’t hold the bind button as you power up the rx. I’m pretty sure you should never do that.
again what learned, like we use to say in German
almost a good video...but you covered up the lights so we can't see your blinking blinking!
It’s barely visible, but you bring up a good point and noticed it after the video was shot. Wasn’t able to reshoot since my other receivers don’t have this issue.
Mine doesn’t work thumbs down
My receiver isn’t getting any power?