How to Make a Homemade Sheet Metal Brake
Вставка
- Опубліковано 10 січ 2019
- Follow me and stay tuned:
Instagram / diyfixman
UA-cam / diyfixman
Facebook / diyfixman
Pinterest / diyfixman
TikTok / diyfixman
Watch all my Videos bit.ly/2kHCZq0
Thank you very much to all my UA-cam followers. Thank you for your great support. You are the ones who motivate me to make interesting new videos for you. Without you it would not have happened! if you like my videos please let me know in the comments, like, share and follow me, your help is much appreciated. If you would like to support my videos feel free to like, share and subscribe, that helps me a lot. I wish everyone a pleasent and enjoyable viewing.
#DIY #TOOLS #HOMEMADE
Honestly the best bends I've seen from a diy brake. I was about to mount my hinges on top but I see the logic here. Great job
Thank you very much my friend
Best diy brake I have seen.
thanks 😊
Best DIY brake I’ve seen
well done brother! Thank you
Today I used a hammer, tomorrow I'm building this. Great project.
Thank you very much my friend
@@DIYFixManI'm buying material to build 1 today finally.
Супер станок без сварки
Very nice bender!
Отличная идея!
Respect. You got a new subscriber.
Thank you very much my friend, I am very happy
פשוט מדהים! 👌
תודה
Gracias por compartir
Great video
Amazing creativity
good for bending polycarbonate too
I want to build one specifically for this reason! :)
ขอบคุณมาก
👍❤
You stuff is awesome
🤗❤️
Excelente muy bueno saludos desde Argentina
❤️
Yep, another brake builder who get's it wrong and the people commenting haven't a clue so make inane comments about how good it is and the best video they've seen!
The clamp bar on ALL brakes has to be able to slide way from the point of bend by the thickness of the metal being bent THEN clamped down!
I've watched dozens of these videos and only seen one that got it right. One of them had to cut the video at the moment it couldn't reach 90 degrees because the clamp was fixed on the edge! He didn't mention it.....
Fine if all you are going to do is bent the same thin tin all the time, it doesn't matter but if you were doing a production run of bends then you need adjustable stops that you can set for whichever thickness metal.
It's not rocket science but sadly there are far too many people posting videos on YT for all kinds of things but who are of low intelligence.
¿Can you post the link for the correct configuration? (for the clamp sliding bar)
This should be easily done by ovaling the holes that mount the clamp bar (on the table side), or adding multiple holes along the bar at different pre set distances.
If you're that concerned about production runs, get a production brake. Or this simple mod does the same.
Hi Jonathan
Can you give me the link for the " one who got it right "please as I need to build one of these?
👏👏👏👏
Thanks
За гайки с ушками - like.
Very good 👍 👍 👍
thanks buddy
Hey other universe.. bite my shiny merel.. woops got the wrong bender... 😂
Very nice good job sir
Thanks 🤗
Very talent person
روعة
Mande as medidas da drobadeira quero fazer uma 2:20 por 1'50 pra dobrar chapa de 1'8
Very nice, ThankQ
Thanks 🤗
С такой штукой я бы тоже гнул всё подряд 😀👍
I guess... if your sheet metal is only 15" wide.
Nice 👍
Thank you 🤗
из за рояльной петли там не будет 90 градусов
Pero como puedes trabajar sin guantes !!!
👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
👏👏👏👏👏👏💖💖💖
❤️❤️❤️❤️
Si pero dobla una pieza de 20' ????
too much free time my friend
freezing / cooling down the aluminum to make it harder for a cleaner cut is something 99% of men fail to do
Who cares.
Plenty of ways to clean it up afterwards.
Who has a freaking freezer in their shop.
Достойно
can you gift detail specifications?
А Федя ломик об каленку гнул
Thank you 🤗
He must like radiation burns on his hands
Oui c bonne
Ненужная херня. Тупо можно в тисках все загнуть.
No hay esa bisagras
There are hinges
👏👏👏👏
Thanks