_Shoot, why can't an AMG body kit still be a sleeper? I mean after all, a 'sleeper' may be something ordinary looking, except for the engine! Back in the day, it would be like seeing a Chevy Impala that appears to have a little six banger, but in all reality, the car had a 409!!!_
Two reasons I love this channel: 1) You push what can be done with a TINY budget compared to so many other UA-camrs. Their content needs seven sponsors, lottery winnings, and a third mortgage to get that Lambo that will be in the shop 4 times before 15k miles. 2) You show the importance of doing as much as possible yourself. Get to know your car, how to drive it, how to fix it, how to mod it, etc.
In several other, (later), videos he talks about going to his job. In one of the dark gray Escalade videos, he talks about riding shotgun so he can edit videos while his wife drives her Escalade. It's distinctly possible he got the day job later. They have a nice house and three kids under age five or so.@@joe_moms_lover
ROLLING COAL In a Mercedes now that's Badass!!........It's super awesome that you're doing some turbo diesel videos too, I have found recently that the diesel lovers Community is very large. I just wrapped up the turbo diesel go-kart today!
@@drewkeen1 something like that. It hits that quickly too. That's why I don't think the cannonball record is in jeopardy with that top speed. You probably need to go 150+ at times.
I'm ready to tune my 648. And my 642. This content introduced me to lsc. And keeps me coming back. I finished diesel school in 89 driving a 79 w116 with a non egr om617 to and fro. This was the first mb diesel in a long line of on/off road engine experience. I stopped driving mb just after I got married (the 79 was my last too) and have driven large vehicles (a couple of eurovans) since. I was reinspired to get back into the diesels by watching the black death series, while I was appalled a Mercedes direct injection diesel would have an injector seal failure with so few miles, i knew there would be solution. I found an 05 for $4k with 149k, picked it up and straightened it up. Rebuild the turbo (turbo international) with a new turbine shaft & rebuilt kit. Replace all charge seals, clean egr, filters and fluids (amsoil diesel synthetic). Repaired turbo actuator internal wiring. Spent $500 total, no dtcs engine or transmission. It is a rocket ship, no turbo lag at all, tires spinning from a stop even with minimal pedal effort. Just got an 07 r320 cdi 4matic, 155k receipts for : new turbo and transmission (turbo verified) full size 2 inch receiver tow hitch (brand new) full infotainment w/ front /rear dvd players, 3 screens, back up (factory) iPhone, hdmi, etc and the factory roof rack. Sorry for the long story, but I have actually enjoyed the e320 and look forward to enjoying the r320 and just wanted to share with you. Thank you P. S. I know you have seen the kids drifting that 750hp 648
First run was test run was the worst, with a lot of smoke, we were still figuring stuff out at that point. With last version of the tune engine smokes only for short period of time before turbo hits max boost ~2400rpm, then it cleares up. It's not the best spooling turbo despite the fact it's a ball bearing unit. I couldn't set max boost earlier than 2400rpm because we were experiencing TQ slippage. There is still some stuff I'm working on to tweak it here and there. It will be almost smokeless, but at this level of modifications some smoke is inevitable.
@@xxxHoskixxx Are there any good resources for adding drive modes? Is this just unlocking existing modes or can one program in custom ones? I'd really like to be able to floor (not kick-down) my 2001 W203 220CDI Automatic but have it shift ealier than it would normally.
I want more CDI vids! This LSC E320 CDI video series is why I flew half way across the US to finally buy one for my wife. She loves it and wants a Marcin tune. The E320 CDI Facebook group has been helpful too.
Love that I thought the mount would go mine did even with less power I changed both mounts and trans mount. If I lived in the states I'd be right there for a tune. Keep it up great job.
Finally, a CDI video. Was getting used to the see through wagon😅. This is my dream build. It’s such a sleeper and keep it that way. Cheers Alex, you’ve taught me a lot about DIY repairs and mods. Just sold my w203 C320 just so I can get one of these. Definitely message you for advice when it arrives. Cheers
Best tuners in Finland have gotten ~450hp/1100nm out of a 420cdi, with a proper remap, and DPF still in the car. The bkorven's e420 has just some crap piggyback tuner...
Holy crap!! Pulls like a freight train, and smokes like one too lol! That CDI is insane! Literally replaced the mounts on mine 2 nights ago in my shop. What a difference. My drivers side was not cracked it all-yours if you want it dude. Damn I wish I was closer to Marcin! Chi town a bit far away :) It's tempting...
I have one of these. They are great. When I travel I get mid 40 mpg. They are spunky, even in stock form. The only failure I have had outside of maintenance is the oil cooler. While fixing that I pulled the intake off and cleaned it up. Removed the flaps and reinstalled. Two things to note, 1 MB extended the SBC warranty to 25 years unlimited miles and 2 they just issued a recall on the sunroof.
@@dubpong No have the om648 with 5 speed. Mine is a 2005 e320 crd. they went OM642 V6 in 2007. Still running and best mpg to date is 52 on a trip to key west
Just did a coming black death fix followed your instructions, new seals under the injectors, car is good for a other 271,000 miles , order the injectors Cleaning and hammer tools, it all worked great. Thanks jacques
That which doesn't break me only makes me stronger!!! What a beast!!! Had the giggles watching this video saying to myself "it's gonna blow! It's gonna blow!" LOL That diesel 6 cyl is amazing!
Congrats Alex and Marcin. I wasn’t too far off of my prediction of 300 HP and 600 lb/ft of torque. Remember-torque hauls the mail! AMG it. Too bad MB/AMG didn’t offer something like this stateside. But...that is why we like you Alex.
Fun to see it's possible to get good power out of these CDI diesels too. Easy on the old mechanical ones, just stick a bigger pump on. Thank you for all the info!
OH, MAN! Now I'm almost definitely gonna keep my "broken" engine to get the one cylinder rehoned or sleeved or whatever then slowly add these things on. What a beast!
Wow! I had a 2005 Cdi! This is the best build you have done! I currently have a modded 2008 Cdi gl320, it it nice but nothing like this! Makes me want another one! Yippie!
Keep the air/fuel ratio in the 18:1 mark, Make the injection wait for the boost(that will make the pick torque to move to 3krpm or so and also will be easy on the engine lower parts. Also less smoke). You can use methanol injection to lower the charge temp making it better to charge the cylinder.
Definitely the old school chain limiter. Make some mounts for a chain from frame to the block motor mount. Leave a little slack for the mount to function. The chain only takes the load in high torque situations. Ez fix and super bulletproof.
This is unnatural! Mere mortals (i.e. me) cry buckets of tears when something breaks on the car. This guy just laughs it off as if it's a great thing! 😱
I had a e280cdi V6 Diesel, same generation but a facelift, 190bhp orginal, after a stage 2 chip it was 298hp. Without a downpipe, it was a great car and enjoyed it for 7 year
Yeah without an EGT number these HP and TQ numbers are pretty meaningless. Making this kind of power with these motors is a fairly straightforward recipe. Looks like it doesn't have enough air for the fuel level and needs a bigger intercooler and a different turbo. They need to invest in an iDash sensot setup to figure out where the low hanging fruit is.
I swear while watching the dyno portion I couldn't help but think "engine mounts" At the end I thought you broke the transmission but then I was like no way lol! Been there before. Good work!
I was wondering what would go first after such a huge mod, thanks for not hiding that part too 😜 It looks like easiest possible fix. I finally heard my name mentioned again 😜
Any diesel tuner that smokes out on a tune without matching the air, doesn’t know what they’re doing. It is completely unacceptable; go watch gale banks, he explains why very well
A little bit of smoke does not hurt a diesels performance too much.. especially if it is just sootin under full load. Would be bad if it threw a real cloud like a fucking steam train.
Yeah, all really tuned Diesels puff a bit especially before turbo get's boost fully up! Even stock tune if you bump gas when standing still and on gear, you'll get small puff and that's ecu spooling turbo up ;)
You don't know what a diesel car is if you said that. Diesel engines always run "dirtier" even without an tune. With an tune it's impossible to not have smoke. You can't make fire without smoke boy.
You can say that all day but i never seen an stage 1 or higher done to an diesel car and not get smoke. The only way to not get smoke out of an diesel exhaust is if it's equipped with an DPF filer, because that filter "catch" all of it until it's full and you need to cut it down because that thing is to expensive to change. I live in an country in EU, here in my country around 60% of cars on the street are diesel, so i know what i'm talking about. Alot of my firend have diesel cars and almost all of them smoke alot when cold or when you rev them unless you still have the DPF filter.
When I saw the Topic I was like on no please not the motor because this is my dream car and I'm going to do exactly as you did..... I had to watch the whole video and damn man it's just a mounting ooh thank God the motor is so strong now I have a reference of how much power and torque thus baby can take.
I had a crazy question... would you ever sell this car?? I absolutely love German diesel sedans!! I had one of the Volkswagen dieselgates that I sold back, and just a couple weekends ago I got in a bad accident in my BMW 328D with my Fiancée. I loved both cars for too many reasons but now I love them for the safety they provide as well. Considering we hoped outta the car to help the other lady in the accident. Thank you in advance for your response!!! Keep making the amazing content! You deserve all the success for helping ppl out as well as Brightening their day!!
Erotikstudio Winkler GmbH i meant efficient and not much of air pollutant when crusing around 2300rpm, even gas cars spit a bunch of carbons under Wide Open Throttle
Crap! That car is sick! I would love to see it in person. I really didn’t know you can build diesel to a beast. Thank you for sharing. Enjoy that car. Hope you don’t sell it.
You can ignore my comment about "stage" because there isn't clear rule how it's defined. My definition goes like this; Stage 1: remap with stock part Stage 2: some supporting mods like bigger intercooler, downpipe, dpf delete etc. Stage 3: bigger turbo and/or bigger injectors. Bigger high pressure fuel pump etc.
Different tuner/ company's go by many different things as to stages. Some do power levels (depending on vehicle) and some do by bolt on kits. My tuner happens to go by a combination. Full emissions deletes, and a hot tune is what his stage 3 is for the m57 diesel engines.
How much power could you get without any black smoke from the back? I have a CDI, would love to build it, but definitely don't want it to smoke at ALL. Right now, the exhaust is unbelievably clean despite missing a cat and EGR.
AMG body kit or keep it a sleeper?
AMG
It deserves AMG treatment :)
Keep it as a sleeper ;)
_Shoot, why can't an AMG body kit still be a sleeper? I mean after all, a 'sleeper' may be something ordinary looking, except for the engine! Back in the day, it would be like seeing a Chevy Impala that appears to have a little six banger, but in all reality, the car had a 409!!!_
A...M...G...
15:19 - a true mechanic never exit a car without opening a window. never trust a car to not lock on you.
Respect.
Hah good catch. Noticed I do the same thing
TRUE i noticed that
valet guys too.
If the keys are in the contact, it's not happening.
Amen
Two reasons I love this channel:
1) You push what can be done with a TINY budget compared to so many other UA-camrs. Their content needs seven sponsors, lottery winnings, and a third mortgage to get that Lambo that will be in the shop 4 times before 15k miles.
2) You show the importance of doing as much as possible yourself. Get to know your car, how to drive it, how to fix it, how to mod it, etc.
Then when hes done YouTubing he goes to work and busts his butt like a regular person.
@@kurta2372 didn't he say in a bunch of videos that UA-cam is his job
Nope, Alex films his yt material in the morning and proceeds to works late shifts. He has mentioned that more than once.
@@joe_moms_lover Second job ;)
In several other, (later), videos he talks about going to his job. In one of the dark gray Escalade videos, he talks about riding shotgun so he can edit videos while his wife drives her Escalade. It's distinctly possible he got the day job later. They have a nice house and three kids under age five or so.@@joe_moms_lover
I would keep it a sleeper, love this channel!
Both is okay buh I'd prefer AMG body kit...
ROLLING COAL In a Mercedes now that's Badass!!........It's super awesome that you're doing some turbo diesel videos too, I have found recently that the diesel lovers Community is very large. I just wrapped up the turbo diesel go-kart today!
ua-cam.com/video/yEdxNw3dMvU/v-deo.html
Now you need to take the CDI and beat the diesel cannonball run record.
The top speed of the e320 isn't very high, mabey a final drive change would help
Also, theyre not made to hold high RPMs for a long time, thats probably their weakspot
@@zkljaja well, they can run max rpm until the fuel runs out.
I was referring to the gears, i have the same car
. And it only gets to 120mph.
@@madmagyver9981 a stock e320 CDI will do 130mph and hit the electronic speed limiter before it runs out of rpm.
@@drewkeen1 something like that. It hits that quickly too. That's why I don't think the cannonball record is in jeopardy with that top speed. You probably need to go 150+ at times.
"Diesel doesn't rev as high as Gasoline" OM606:"Hold my beer"
*OM648
@@greaseonmyhands493 They can both manage up to 7000 RPM but the 606 is the one for Big numbers and engine swaps.
@@TheGalifrey the engine in the video is an OM648
@@greaseonmyhands493 the statement in the video was "diesels don't rev as high as petrol" I was arguing that the Om606 does, get with the plot FFS
I'm ready to tune my 648.
And my 642. This content introduced me to lsc.
And keeps me coming back. I finished diesel school in 89 driving a 79 w116 with a non egr om617 to and fro. This was the first mb diesel in a long line of on/off road engine experience.
I stopped driving mb just after I got married (the 79 was my last too) and have driven large vehicles (a couple of eurovans) since.
I was reinspired to get back into the diesels by watching the black death series, while I was appalled a Mercedes direct injection diesel would have an injector seal failure with so few miles, i knew there would be solution.
I found an 05 for $4k with 149k, picked it up and straightened it up.
Rebuild the turbo (turbo international) with a new turbine shaft & rebuilt kit. Replace all charge seals, clean egr, filters and fluids (amsoil diesel synthetic). Repaired turbo actuator internal wiring.
Spent $500 total, no dtcs engine or transmission. It is a rocket ship, no turbo lag at all, tires spinning from a stop even with minimal pedal effort.
Just got an 07 r320 cdi 4matic, 155k receipts for : new turbo and transmission (turbo verified) full size 2 inch receiver tow hitch (brand new) full infotainment w/ front /rear dvd players, 3 screens, back up (factory) iPhone, hdmi, etc and the factory roof rack.
Sorry for the long story, but I have actually enjoyed the e320 and look forward to enjoying the r320 and just wanted to share with you.
Thank you
P. S.
I know you have seen the kids drifting that 750hp 648
FINALLY!! E320 CDI owner here and so excited to finally see this.
Thanks Alex.
You need to turn up the boost even more, not enough air going in.
First run was test run was the worst, with a lot of smoke, we were still figuring stuff out at that point. With last version of the tune engine smokes only for short period of time before turbo hits max boost ~2400rpm, then it cleares up. It's not the best spooling turbo despite the fact it's a ball bearing unit. I couldn't set max boost earlier than 2400rpm because we were experiencing TQ slippage. There is still some stuff I'm working on to tweak it here and there. It will be almost smokeless, but at this level of modifications some smoke is inevitable.
@@xxxHoskixxx Are there any good resources for adding drive modes? Is this just unlocking existing modes or can one program in custom ones? I'd really like to be able to floor (not kick-down) my 2001 W203 220CDI Automatic but have it shift ealier than it would normally.
Amazing, Marcin is a legend
Marcin did my CDI and it was perfect
@LegitStreetCars look at my instagram @blazejkuba - you will like the look of the w211
Can i have his contact or insta?
Did you found it?
I want more CDI vids! This LSC E320 CDI video series is why I flew half way across the US to finally buy one for my wife. She loves it and wants a Marcin tune. The E320 CDI Facebook group has been helpful too.
Mercedes KNOWS how to make a great sounding diesel
Keep it sleeper! Love these CDI vids as an owner of CDI Benz
Love that I thought the mount would go mine did even with less power I changed both mounts and trans mount. If I lived in the states I'd be right there for a tune. Keep it up great job.
Wooow, i love seeing the engine twisting from the torque on the front footages
Finally, a CDI video. Was getting used to the see through wagon😅. This is my dream build. It’s such a sleeper and keep it that way. Cheers Alex, you’ve taught me a lot about DIY repairs and mods. Just sold my w203 C320 just so I can get one of these. Definitely message you for advice when it arrives. Cheers
Safety is our number own priority!
This mercedes smoked a lot less than that broken ass Range Rover you "fixed" :)
Your heading for a million plus subs bro ! Just keep up the awesome content!
Imagine the things you can do with E420 diesel.
Or an Audi A8 TDI 4.0TDi.
That way you would have power AND traction.
Nah, check out Audi Q7 with 6.0 V12 diesel.
Best tuners in Finland have gotten ~450hp/1100nm out of a 420cdi, with a proper remap, and DPF still in the car. The bkorven's e420 has just some crap piggyback tuner...
@@Turbokilpuri tuikku onki kova jätkä
Wonder how much HP and Torque they could get out of my W123 1982 300D stock 120 HP Turbodiesel?
Holy crap!! Pulls like a freight train, and smokes like one too lol! That CDI is insane! Literally replaced the mounts on mine 2 nights ago in my shop. What a difference. My drivers side was not cracked it all-yours if you want it dude. Damn I wish I was closer to Marcin! Chi town a bit far away :) It's tempting...
YES! The CDI is back! AMG kit it!
I have one of these. They are great. When I travel I get mid 40 mpg. They are spunky, even in stock form. The only failure I have had outside of maintenance is the oil cooler. While fixing that I pulled the intake off and cleaned it up. Removed the flaps and reinstalled. Two things to note, 1 MB extended the SBC warranty to 25 years unlimited miles and 2 they just issued a recall on the sunroof.
you have the OM642 V6 diesel engine with probably the 7g tronic transmission. This one on the video is OM648 inline 6 with 5-speed automatic.
@@dubpong No have the om648 with 5 speed. Mine is a 2005 e320 crd. they went OM642 V6 in 2007. Still running and best mpg to date is 52 on a trip to key west
@@aviator97msncom what do you mean that there is no om648 with 5-speed tranny?
So glad you have the E320 back on the channel, enjoy diesel cars and enjoy watching you push this platform.
Finally a Diesel vid! It’s been a little.
First it was trying to jump off the dyno then the engine tried to jump out of the bay! Torque monster!
Looking at the front shots of the dyno run, it looks like that motor mount was well and truly broken already at that point.
Now, I want one! Thanks, Marcin, for showing what is possible with a Mercedes diesel.
Just did a coming black death fix followed your instructions, new seals under the injectors, car is good for a other 271,000 miles , order the injectors Cleaning and hammer tools, it all worked great. Thanks jacques
I love the content of this channel! That car pulls like a bulldozer! You must order more engine mounts ...!
That which doesn't break me only makes me stronger!!! What a beast!!! Had the giggles watching this video saying to myself "it's gonna blow! It's gonna blow!" LOL That diesel 6 cyl is amazing!
Congrats Alex and Marcin. I wasn’t too far off of my prediction of 300 HP and 600 lb/ft of torque. Remember-torque hauls the mail! AMG it. Too bad MB/AMG didn’t offer something like this stateside. But...that is why we like you Alex.
Brilliant… great how you both laughing at the motor mount fail at end!!!! 🤣🤣🤣
Fun to see it's possible to get good power out of these CDI diesels too. Easy on the old mechanical ones, just stick a bigger pump on. Thank you for all the info!
OH, MAN! Now I'm almost definitely gonna keep my "broken" engine to get the one cylinder rehoned or sleeved or whatever then slowly add these things on. What a beast!
Great to come see the progress! Sleeper FTW!
Wow! I had a 2005 Cdi! This is the best build you have done! I currently have a modded 2008 Cdi gl320, it it nice but nothing like this! Makes me want another one! Yippie!
Keep the air/fuel ratio in the 18:1 mark, Make the injection wait for the boost(that will make the pick torque to move to 3krpm or so and also will be easy on the engine lower parts. Also less smoke). You can use methanol injection to lower the charge temp making it better to charge the cylinder.
Swietna robota Marcin. tak trzymaj
Definitely the old school chain limiter. Make some mounts for a chain from frame to the block motor mount. Leave a little slack for the mount to function. The chain only takes the load in high torque situations. Ez fix and super bulletproof.
I recently had my 3.0 tdi remapped, from 240hp/500 to 300hp/606hp... really flies for a 1850 car!
This is unnatural! Mere mortals (i.e. me) cry buckets of tears when something breaks on the car. This guy just laughs it off as if it's a great thing! 😱
Well, it’s a 10 minute job for him and he knows how to do it and he even got the spare part on the shelf at home! =)
I had a e280cdi V6 Diesel, same generation but a facelift, 190bhp orginal, after a stage 2 chip it was 298hp. Without a downpipe, it was a great car and enjoyed it for 7 year
Banks power needs to see this
I was thinking the same thing. Gale Banks would have plenty to say about all that soot as evidence of unburned fuel and lost power.
That would be hysterical.
@@maxcactus7 he would be asking what are the egt's WHAT ARE THE EGT'S?!?
Yeah without an EGT number these HP and TQ numbers are pretty meaningless. Making this kind of power with these motors is a fairly straightforward recipe. Looks like it doesn't have enough air for the fuel level and needs a bigger intercooler and a different turbo. They need to invest in an iDash sensot setup to figure out where the low hanging fruit is.
i'd like to see Gale Banks reaction as well
I swear while watching the dyno portion I couldn't help but think "engine mounts" At the end I thought you broke the transmission but then I was like no way lol! Been there before. Good work!
Keep it as a sleeper ;)
This is so cool!! So much feeling/seeing power than gas engines!!! Like it a lot!
Excellent job! I'd keep it a sleeper to the unsuspecting.
I was wondering what would go first after such a huge mod, thanks for not hiding that part too 😜 It looks like easiest possible fix. I finally heard my name mentioned again 😜
Will fix the motor mount and get some track times Alex, Your audience demands it.
CDI ⚠️⚠️
I really enjoy watching your Mercedes content
Love it!
Thanks for the play list of videos since the beginning.
You should make AMG Menu in speedometer. It shows oil temperature which is quite helpful with tuned CDI. 😉
alright , more CDI!!!!
So what happened with this build?? It is Feb 9th 2022 and the last date for a video was May 16, 2020
Hey Alex! How come they haven’t been anymore cdi videos?? What happened with this thing ?
When the engine wants to fly out of the hood because of the massive torque.
That Mercedes looks like a beast of a car, keep up the great job !
Awesomeness! I always have fun watching the vids. Keep ‘em coming Boss 😎
Any diesel tuner that smokes out on a tune without matching the air, doesn’t know what they’re doing. It is completely unacceptable; go watch gale banks, he explains why very well
You’re kinda correct! the intercooler is the limiting factor!
I am a simple guy.. I see a Mercedes video I press like
If airfuel is good then your intercooler is too small. Too much smoke.
A little bit of smoke does not hurt a diesels performance too much.. especially if it is just sootin under full load.
Would be bad if it threw a real cloud like a fucking steam train.
Yeah, all really tuned Diesels puff a bit especially before turbo get's boost fully up! Even stock tune if you bump gas when standing still and on gear, you'll get small puff and that's ecu spooling turbo up ;)
You don't know what a diesel car is if you said that.
Diesel engines always run "dirtier" even without an tune.
With an tune it's impossible to not have smoke.
You can't make fire without smoke boy.
@@noitrex Smoke is literally incomplete combustion because of too much fuel. I think Gale Banks is smarter than all of you, including me.
You can say that all day but i never seen an stage 1 or higher done to an diesel car and not get smoke.
The only way to not get smoke out of an diesel exhaust is if it's equipped with an DPF filer, because that filter "catch" all of it until it's full and you need to cut it down because that thing is to expensive to change.
I live in an country in EU, here in my country around 60% of cars on the street are diesel, so i know what i'm talking about.
Alot of my firend have diesel cars and almost all of them smoke alot when cold or when you rev them unless you still have the DPF filter.
Keep in mind that the whole Europe is subscribed to you by this W211 ❤
When I saw the Topic I was like on no please not the motor because this is my dream car and I'm going to do exactly as you did..... I had to watch the whole video and damn man it's just a mounting ooh thank God the motor is so strong now I have a reference of how much power and torque thus baby can take.
The main thing I missed on my 2002 ml 320 was the big triangle that would just spook you, glad to see yours still has it haha.
Awesome to see the diesel back on your channel! I hope you will do a similar project on a newer E250......
Another great video,best channel on you tube by far
You can tell Marcin is legit when he rolled down the window before getting out of the car. CarWizard just explained why true shops mechanics do that!
Burgundy w204 in the background when reading out dyno, looks 👌
Hi Alex, I really enjoy your content! I just watched this series again. Just one question, what happened to the mercedes diesel?
Diesel is crazy, ma highway tractor have a 13 liters engine 510 HP-1950ft/lbf. Pull weight like crazy at 38 psi of boost ! Insane numbers...
What a beast of a car, epic build.
Nice job guys!))om648 and om606 are best 6inline engines ever made!
What a f***ing machine, crazy torque!! Really impressive
I had a crazy question... would you ever sell this car?? I absolutely love German diesel sedans!! I had one of the Volkswagen dieselgates that I sold back, and just a couple weekends ago I got in a bad accident in my BMW 328D with my Fiancée. I loved both cars for too many reasons but now I love them for the safety they provide as well. Considering we hoped outta the car to help the other lady in the accident. Thank you in advance for your response!!!
Keep making the amazing content! You deserve all the success for helping ppl out as well as Brightening their day!!
Good stuff man! If you ever wanna test race a tuned 335d, let me know 😁
I have a e320 cdi because of your videos!
Whatever happened to this car
ya. . . just quit
Marcin, a Great mechanic
Love your videos and I am in line to purchase the "LSC CDI". I promise to also have the same license plates in my state😁
It looked like the engine was trying to break out of the and attack you!!
Diesel Demon-Posession!!
Brawo, panie Marcinie! Piekna robota. @marcinhoski Nice work, guys. Makes me want to hunt down a CDI for myself.
Cool project. More collaboration with this guy!
Ignore these people triggered from the black smoke! They just envy the power you made with the cdi! I bet the cdi is very efficient on cruise!
Erotikstudio Winkler GmbH i meant efficient and not much of air pollutant when crusing around 2300rpm, even gas cars spit a bunch of carbons under Wide Open Throttle
Love this build man.. somethings about the W211 just gets to me
Crap! That car is sick! I would love to see it in person. I really didn’t know you can build diesel to a beast. Thank you for sharing. Enjoy that car. Hope you don’t sell it.
In Hungary there is BMW e90 335d with 450hp and 850nm, it does the 1/4 mile in 12 seconds :D
Love the diesel content. I've got a stage 3 335d, made 356hp/542tq on a hub dyno.
That's stage 1 power with everything stock. Just saying.
@@keijokojootti7790 all I have is a down pipe, and emissions deletes.
You can ignore my comment about "stage" because there isn't clear rule how it's defined.
My definition goes like this;
Stage 1: remap with stock part
Stage 2: some supporting mods like bigger intercooler, downpipe, dpf delete etc.
Stage 3: bigger turbo and/or bigger injectors. Bigger high pressure fuel pump etc.
Different tuner/ company's go by many different things as to stages. Some do power levels (depending on vehicle) and some do by bolt on kits. My tuner happens to go by a combination. Full emissions deletes, and a hot tune is what his stage 3 is for the m57 diesel engines.
@@shapoopeedee Fair enough.
My bro got darkside developments turbo but got some other geezer to do the map?? Darkside are the boys for diesel remapping 🙌🏼
Marcin is such an kind nice guy
That car was a proper killer!
Looking forward to the Caprice Police car build!
That is a bad ass diesel there has to be some G Force going on with that much torque.
Marcin you are the MAN!
ooooooooooooooh boy look at this guy with the fancy license plates! starting an empire he is!
I was thinking the motor mount was questionable during the dyno runs. Look at how much it was lifting during those.
How much power could you get without any black smoke from the back?
I have a CDI, would love to build it, but definitely don't want it to smoke at ALL. Right now, the exhaust is unbelievably clean despite missing a cat and EGR.
Damm Alex your CDI is a beast now! Great video bro!🐟
I got paddle shifters in my e320cdi they work great.
I have a 2003 E320 CDI and SBC Hold and Stop came with it.
Right. You probably don't live in the U.S. then
@@LegitStreetCars That’s interesting to know that US cars are programmed differently. The beauty of computer cars 😂
Awesome mercedes video 💪🏼💪🏼😎👌🏼