Saved my life this vid thanks! Quick adjustment and off I go ..thanks 🍻 Big panic this morning as was stalling as soon as I let the clutch go….quick fiddle and working fine now !
The adjustment on the lever is your minor adjustment the adjustment on the cable is considered major adjustment and the pressure plate is maintenance adjustment... No more then a nickels worth between perch and lever of Freeplay...
Thank you for the demonstration. I have a couple of questions. 1- What would be a good starting point? Lever half way, the cable half way and then adjust the screw? 2- when I loosen the lever and the cable all the way to maximum cable slack, then, I screw in the clutch also all the way, the wheel continues to rotate (with no resistance applied) is that normal? 3- it is hard to get my bike into neutral. When I do manage to get it into neutral and tilt the bike to the right the transmission engages. Tilt it to the left, it disengage. Could this be a clutch adjustment or is my transmission bad? I bought it second hand with only 182kms on the odometer. Looking forward to your response.
2 try to screw it all the way in and then apply the rear brake it should stop without affecting the engine tone question 3 if the clutch isnt adjusted properly you will struggle to get into neutral
So I've got a ybr 125 put new. Clutch in its a wet clutch have adjusted cable to factory specs and clutch still slips I've done the end screw on the clutch it's. Self all the way in u till. I hit clutch aquater and back of quarter of a turn but bike is still slipping not as bad as it was but still not delivering the full power any help please
it is quite hard to diagnose an issue without seeing the bike directly but i would check the clutch basket itself the plates may be biding in there or maybe replace the 4 tension spring
My yamasaki ym50 struggles to go from 1st gear to 2nd. I’m not sure if it’s something to do with the clutch needing tightening or if it’s another issue. Any suggestions?
@@Ridingreviews Yh the gear indicator goes blank sometimes inbetween neutral and 1st but you can tell it’s still in gear because it tries to pull of when you release the clutch
Thank you for your vlog tutorial about how to adjust the clutch thank you again.God Bless.
Glad it helped stay tuned for more helpful tutorials
Saved my life this vid thanks! Quick adjustment and off I go ..thanks 🍻 Big panic this morning as was stalling as soon as I let the clutch go….quick fiddle and working fine now !
i am really glad my video helped you out that is what they are there for
The adjustment on the lever is your minor adjustment the adjustment on the cable is considered major adjustment and the pressure plate is maintenance adjustment... No more then a nickels worth between perch and lever of Freeplay...
thank for adding you say it better than i can
@Ridingreviews oh yeah great job on the video... Just my 2 cents from mmi... Haha... Keep it up... Thanks...
Thank you for the demonstration. I have a couple of questions.
1- What would be a good starting point? Lever half way, the cable half way and then adjust the screw?
2- when I loosen the lever and the cable all the way to maximum cable slack, then, I screw in the clutch also all the way, the wheel continues to rotate (with no resistance applied) is that normal?
3- it is hard to get my bike into neutral. When I do manage to get it into neutral and tilt the bike to the right the transmission engages. Tilt it to the left, it disengage. Could this be a clutch adjustment or is my transmission bad? I bought it second hand with only 182kms on the odometer.
Looking forward to your response.
2 try to screw it all the way in and then apply the rear brake it should stop without affecting the engine tone question 3 if the clutch isnt adjusted properly you will struggle to get into neutral
@@Ridingreviews will do that.
Thanks again
@@Ridingreviews Just to let you know. Clutch is now perfect 👌
Thank you
is there a way to just losen the tension of the clutch? my hand gets quite tired after a few minutes riding :(
How is the bike not stalling if its in 1st gear with no clutch pulled in ?
It's not bearing any weight on the bike cause it to free move. If the back wheel was on the ground it would stall immediately
My bikes clutch is releasing at the very end. Which adjustment will get the clutch to engaged sooner? Closer to the grip.
if there is no adjustment already on the cable you will have to adjust it on the engine
So I've got a ybr 125 put new. Clutch in its a wet clutch have adjusted cable to factory specs and clutch still slips I've done the end screw on the clutch it's. Self all the way in u till. I hit clutch aquater and back of quarter of a turn but bike is still slipping not as bad as it was but still not delivering the full power any help please
it is quite hard to diagnose an issue without seeing the bike directly but i would check the clutch basket itself the plates may be biding in there or maybe replace the 4 tension spring
Cheers iv got new springs so will put them. On and see if that helps make a difference
I know this question is unrelated to the video but what what are you wearing? I know it’s a smart watch but can’t work out what make and model. Thanks
Lol is is a samsung gear s3 watch
On my. Bike i here a clunk when put it in first witch way shoukd i adjust it. thanks
were is the biting point on your clutch lever
My yamasaki ym50 struggles to go from 1st gear to 2nd. I’m not sure if it’s something to do with the clutch needing tightening or if it’s another issue. Any suggestions?
I would say it will be clutch for that i brt it is hard to get into neutral aswell
@@Ridingreviews Yh the gear indicator goes blank sometimes inbetween neutral and 1st but you can tell it’s still in gear because it tries to pull of when you release the clutch
This adjustment work on Harley Sportsters?
the cable adjustment will
My clutch is to far down and I dont know how to fix it. Can you please help
You can adjust it on the handlebars, or there is an adjuster in the middle of the cable. What is wrong with your bike? What are the symptoms
@@Ridingreviews I fixed it
3:58 :)))))