Basic repair principles are ok except I would be shocked if the coil didn’t rub on the magnet when completed. You must use spacer shims for proper coil centering. Also your coil depth is guess work.
this size is easier to centerize the cone. smaller than 4-5" or bigger than 12"-15", often after 2-3 months, you hear the noise of scratching and need to recone agaaaain 😫 a few pieces of thin papers must be slided inside center coil to prevent this problem till glue will be dried 😉
Yo no me dedico ese pero sinceramente lo hago mejor que él nunca me he quedado mal una bocina yo mejor no sabía ni un video así con ese tipo de forma de trabajar que me estuvieran viendo wowww
Pardon my ignorance on speaker basics - would like a tiny direction for my problem. I bought a 8inch 50 watt woofer (not sub woofer) about 15 years back, used it for few hours and it sounded good. I opened it today and connected it to my amplifier and it outputs too little volume. I gently pushed the cone and spider up, and the volume goes up and it vibrates well. How can I fix it? The spider feels hard... the soft rubber on the outer edge of the cone is soft/flexible...
You shouldn't scrape the insolation off the coil wire either. Instead you must either use molten solder or lighter flame to do so. Good work but you will get 7 out of 10 from me.
Buenas noches Excelente la tutoría. Aquí en Campeche, México, los técnicos usan resistol blanco # 850. En la tutoría no se cómo se llama el pegamento que usa. Será que lo vendan aquí en México y con que se pide. Habrá en cualquier eléctronica. Saludos cordiales. Desde Nunquiní, Campeche, México.
Please take care , many Amaturist seekers will try to take this as a basic ingredient to learn & practically perform this project. All corrected steps in the suggestion box be taken care of and new recording be uploaded for everbodys' s benefit.
Hi I have an audiopipe 12in. Txx blue eye candy sub that was passed down from my brother that has passed away. So know it's the only brand I run. The dust cover sperated from the coil but the coil is still good. I had it in a sealed box and hit some low hz. that's the reason for it happening. It don't have to be the blue aluminum look just want to hear it play and bring back some memories of him. Please help ppl say throw it out and get a new one but I can't seem to do that. Please help me even if it is bad news.thanks for the time on this issue. Keep the videos coming they help out a lot.
You're going to have a hard time playing that at a low volume. The coil will be touching the magnetized center. You must first assemble the coil, the spider and the basket (diaphragm) before glueing it to the frame.
Hello sir Dalton. I have a loud speaker but I want to get more bass from it. I was suggesting to transfer the cone to another basket that can accommodate a bigger voice coil. Already i have the basket and it has a has a bigger magnet. Will this idea work out as i continue to save some cash to buy a perfect driver? Please help me
Is a good video but i would like you to do a repair for Sony home theater woofer speaker since mine got burnt half,coz Sony says the connection between the 2 coils is cut. But the woofer does good in moderate volume, but when i go higher my home theater system go off and give a warning of power protect. So I don't know how to handle the woofer speaker . Any help?
Eso es lo que también me dejó pensativo... como centró la bobina respecto al entrehierro y a la circunferencia externa del entrehierro? ... (No la centró en ningún momento)
The rusted body structure needs to pre treated manually before going on for the reconeing. Higher magnetic flux at bore & pole peace area will attract the rusted particles to reach there, even when the speaker is not in action. Secondly if structure is showing the tendency of rust formation, it should be nibbed at the earliest to save the refurbished component of same symptoms & saving other adjoining components as spilling of these particles are not good to other PCB plates like crossover Network or Mid Speakers in the enclosed Columb.
он забыл что надо центровать, что-то измерял, я уж думал сейчас правильно выставит центр катушки по центру железа, а она улетела на дно магнита, он так и приклеил, лопух, 99% пишут nice work )))
E muito simples de monta um alto falante mais ele está fazendo o proseso mais difícil e só calsar. 1 passo. Calsar abombina. 2 depois passa acola. Nas parte metálica 3 cola abombina e 4 desses as cone faz a saldagem da bombima para os conequitores do alto falante. Desse o cone e o tapes.
For the circuit diagram please visit here
shorturl.at/FNS56
Tnx master..we are watching 🙂😌🙂 very useful technic
Basic repair principles are ok except I would be shocked if the coil didn’t rub on the magnet when completed. You must use spacer shims for proper coil centering. Also your coil depth is guess work.
How do you decide coil depth
वेरी नाइस स्पीकर रिपेयरिंग वर्क थैंक्स फॉर विडियो ब्रो 👍👍
බොහොම ස්තුතියි ඔබට පැහැදිලිව රූපසටහන පෙන්වාදීම පිලිඹදව.
New Again 🔊
How did you decide magnetic center and physical center of voice coil?
this size is easier to centerize the cone. smaller than 4-5" or bigger than 12"-15", often after 2-3 months, you hear the noise of scratching and need to recone agaaaain 😫 a few pieces of thin papers must be slided inside center coil to prevent this problem till glue will be dried 😉
They didn't center the voice coil. This is a bad video because they did not use shims.
Sangat rapi dan keren,sangat ber manfaat sekali
Hello Master, im already waching your vedios, im a newbe vloger for electronics, i have got some ideas, so thats all thank u, god bless u master...
electronicshelpcare.net/tda2050-mono-circuit-diagram/
Great 👍 detailed fine work
Professional 🔈🔈🔈🔈🔈
Ramses elektronik olarak aramızda görmekten mutluluk duyarız görüntüleme ve ses sistemleri
Yo no me dedico ese pero sinceramente lo hago mejor que él nunca me he quedado mal una bocina yo mejor no sabía ni un video así con ese tipo de forma de trabajar que me estuvieran viendo wowww
Your videoes seem quality and good
Super demo thankyou bro God bless your work
At what point did he center the coil?
Good👌👌👌naxt ⏩⏩⏩
electronicshelpcare.net/led-music-level-indicator-circuit-diagram/
बहुत बढ़िया बहुत सुंदर
Pardon my ignorance on speaker basics - would like a tiny direction for my problem. I bought a 8inch 50 watt woofer (not sub woofer) about 15 years back, used it for few hours and it sounded good. I opened it today and connected it to my amplifier and it outputs too little volume. I gently pushed the cone and spider up, and the volume goes up and it vibrates well. How can I fix it? The spider feels hard... the soft rubber on the outer edge of the cone is soft/flexible...
I have the same problem with two entire media rooms. Did you ever find a solution?
Good hit, Kuki dand 🇮🇳🇮🇳👍👍👍
Super ,nice work .
Good job 👍👍👍
Nice one sending my support fullpack new friend fullwatch from oriental mindoro Philippines
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
You shouldn't scrape the insolation off the coil wire either.
Instead you must either use molten solder or lighter flame to do so.
Good work but you will get 7 out of 10 from me.
Bien por tu vídeo amigo oye una pregunta , qué tanto debe d entrar el embobinado ? Gracias d antemano amigo.👍
Nice Tec👌👍
Buenas noches
Excelente la tutoría.
Aquí en Campeche, México, los técnicos usan resistol blanco # 850.
En la tutoría no se cómo se llama el pegamento que usa.
Será que lo vendan aquí en México y con que se pide.
Habrá en cualquier eléctronica.
Saludos cordiales.
Desde Nunquiní, Campeche, México.
Perdón.
Con qué nombre se pide.
You cannot do it exactly without putting spacer along the sides of the coil to have the same clearance..it should be done carefully.
X ray or fan binding wala kagaz is the best for spacer
Grande colega te felicito
நல்ல பதிவு 👍👍👍👍
Very good speaker repair
Def done the HARDER way! Still nicely done, easier to just buy parts that FIT!
How do you identify positive and negative
Good 👍 job
Super ❤❤❤😊
You are doing well
serviço muito bagaceira, ninguém faz um serviço tão porco assim.................
sir, how about clearance, voice coil between, bottom center mag net?
thanks verry nice video
voice coil placement details super
What kind of adhesive can be used to repair small slit on JBL L110 driver?
Keep that work up 💪 👍 #BRUH#
Please take care , many Amaturist seekers will try to take this as a basic ingredient to learn & practically perform this project. All corrected steps in the suggestion box be taken care of and new recording be uploaded for everbodys' s benefit.
I mean, I'm not the most ocd person there is, but that membrane cut was something else.
Mantap
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Watching lheoda tech sir nice sharing
Hi I have an audiopipe 12in. Txx blue eye candy sub that was passed down from my brother that has passed away. So know it's the only brand I run. The dust cover sperated from the coil but the coil is still good. I had it in a sealed box and hit some low hz. that's the reason for it happening. It don't have to be the blue aluminum look just want to hear it play and bring back some memories of him. Please help ppl say throw it out and get a new one but I can't seem to do that. Please help me even if it is bad news.thanks for the time on this issue. Keep the videos coming they help out a lot.
Даже не сомнивался что он его не будет включать на видео))) магнитный зазор не выставил.
да он там пиздец всё криво сделал, 100 литров клея вылил
Can you use super glue (cyanoacrilate), instead of epoxy?
No
Good👍
Khub valo
Very nice video
Salut vous êtes au cameroun ? J'aimerais.
Tarik sis semangko...
Where dis u get those parts I've tried to find it for months 😭😭😭
Manteb bro
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Superb sir
Very good
which types of glue is needed
The type that shoe maker uses.
You're going to have a hard time playing that at a low volume.
The coil will be touching the magnetized center.
You must first assemble the coil, the spider and the basket (diaphragm) before glueing it to the frame.
true, also why cut the neck of the coil so short, there will be hardly any length left to attach the cone. problems
also what of the spacers to keep the coil centered before applying the glue
Hello sir Dalton. I have a loud speaker but I want to get more bass from it. I was suggesting to transfer the cone to another basket that can accommodate a bigger voice coil. Already i have the basket and it has a has a bigger magnet. Will this idea work out as i continue to save some cash to buy a perfect driver? Please help me
Es un desmadre para repara el bajo. Falto centrar la bobina
Hello great work. Where did you buy the parts from online.
You are doing well sir
Obs tem que centralizar o centro da bina para não arrastar no canto para não fazer ruído. Isso ele não amostra no vidio eu já fiz varios
Nice Bro
Is a good video but i would like you to do a repair for Sony home theater woofer speaker since mine got burnt half,coz Sony says the connection between the 2 coils is cut. But the woofer does good in moderate volume, but when i go higher my home theater system go off and give a warning of power protect. So I don't know how to handle the woofer speaker . Any help?
Hamare pass 50 watt espikr hii to kitna khracha lge ga
Good
No sabes....hoy ..y loscentradores estás weeeeyyyy....😁😁😁😄😁😄😁
Como se centro la bobina sin acetatos o negativo de foto,este si me salio chingon...
Eso es lo que también me dejó pensativo... como centró la bobina respecto al entrehierro y a la circunferencia externa del entrehierro? ... (No la centró en ningún momento)
Super supr🎉
The rusted body structure needs to pre treated manually before going on for the reconeing. Higher magnetic flux at bore & pole peace area will attract the rusted particles to reach there, even when the speaker is not in action. Secondly if structure is showing the tendency of rust formation, it should be nibbed at the earliest to save the refurbished component of same symptoms & saving other adjoining components as spilling of these particles are not good to other PCB plates like crossover Network or Mid Speakers in the enclosed Columb.
Катушку в зазоре отцентровал по верхнему краю шайбы. Не правильно. Центр шайбы с центром катушки должны совпадать.
Он вообще будет играть?😅
он забыл что надо центровать, что-то измерял, я уж думал сейчас правильно выставит центр катушки по центру железа, а она улетела на дно магнита, он так и приклеил, лопух, 99% пишут nice work )))
E muito simples de monta um alto falante mais ele está fazendo o proseso mais difícil e só calsar. 1 passo. Calsar abombina. 2 depois passa acola. Nas parte metálica 3 cola abombina e 4 desses as cone faz a saldagem da bombima para os conequitores do alto falante. Desse o cone e o tapes.
Terimakasi sudah memberi tahu saya 1+
Pas de calage pour la bobine ?
What is name of all components. Like voice call and the other?.
Sir bol kar sikhate to or achha ho ta sir good app sa koi nhi batata sir
Jordar
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Terimakasi sudah memberi tahu saya
I am also in electronic electrical mechanical field
What adhesive do you use for speaker?
Araldite and fevicol sr
This video used for dendrite and araldite
I want to repair my JBL flip2.....how can I repair it
Mantab broo
Faltou centralizar a bobina com um papel
Tô esperando ele centralizar tbm faltou
เยี่ยมเลย..😊😊
Bhai....coil ki centering kab ki.....
Y que no centran la bobina? Luego roza y se escuchan ruidos extraños en la bocina!!
Boa noite meu amigo
electronicshelpcare.net/how-to-make-speaker-crossover/
Saludos
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Ahuja 400 wat mein Kitna number ka koil lagta hai bhaiya bataiye na please mere ko kharidna hai
electronicshelpcare.net/how-to-make-speaker-crossover/
Como dijieron la mayoria de todos ..le falto el centrado de la bobina y cuanto milimetros deja de bobina hacia arriba del nucleo del bobinado
Sir 6" woofer speaker 10 watt coil ki jayga may 20 watt coil dull sakta hu kaya
Thanks for sharing .
Super nada
Hello can car speaker used at hi fi system
Lem apa yg dipake utk ngelem memran spiekerx gan
Josss
Are you trying to beat the speed of light???
👍👍👍👍💯💯💯💯💯
அண்ணா இது என்ன பேஸ்ட் கொஞ்சம் சொல்லுங்கள் அண்ணா
Paper cone best or woofer cone best, which one best.