CODE '12' states "I have entered ABS diagnosis mode, I will flash this 3x then move on code-by-code (flashing EACH 3 times for you) and then END sequence again with Code '12' as an outro. Would it have killed someone to at least drop a link to all the scanning hard/software being used in this vid?
I have 2009 Honda Accord Sedan V4. When i drive the car and pass any uneven surface than ABS indicator, the VSA indicator and the brake system indicator come on. Moreover, when I park the car for more than 8 hours at night than lights goes away until i cross any uneven surface. I used Lunch tech X431 code reader and it gives the code 121-01, VSA modulator solenoid valve malfunction. But I hope that modulator does not have any problem, as the lights did not stay permanently. Some times I drove the car for 35 KM but the indicators stay off Guys please help me ....
@phillip Small > By DOT specs, the OBD-2 connector has to be within 22 inches of the steering wheel. Center or edge, you decide. I can not speak for your 2009, but the center console on Honda’s mini-van, was on the right side of the console behind a plastic door. It is 22” but a the crow flies. A flash light and a good look around will locate it, they are all shaped the same and have 16 terminals. It could be next to the fuse relay center on the side of the dash, just turned sideways. It is June 2021, hope you have found it by now! Best of luck. Isuzu Master Tech, ASE Master Tech since 1978 - Retired.
Excellent video! Big help.
Very well plan and showing education, it is a "school" style. thank you.
J Tsai Thank you for your comment. I'm glad you liked the video and hope you take the time to check out some other videos we have here on the channel.
Great! what type of sensor? thanks.
Would this pin jump work for a 1999 Honda Passport? Have the book for the vehicle but not familiar with ABS system.
Yes
Thanks for checking out the video. Please feel free to ask any questions or leave any feedback you have.
CODE '12' states "I have entered ABS diagnosis mode, I will flash this 3x then move on code-by-code (flashing EACH 3 times for you) and then END sequence again with Code '12' as an outro.
Would it have killed someone to at least drop a link to all the scanning hard/software being used in this vid?
So I just did this in my 1999 Isuzu Rodeo... I got codes 24, 22, 61, 52, 15, 62, 53, 63, and 63 again. Damn.
I think that's more of a problem with the modules
Not sensors
Is this vehicle reliable for heavy driving use? I’m thinking about purchasing one tomorrow!
6000 scanner to tell you too use a peace of wire, don't make sense
I have 2009 Honda Accord Sedan V4. When i drive the car and pass any uneven surface than ABS indicator, the VSA indicator and the brake system indicator come on. Moreover, when I park the car for more than 8 hours at night than lights goes away until i cross any uneven surface.
I used Lunch tech X431 code reader and it gives the code 121-01, VSA modulator solenoid valve malfunction. But I hope that modulator does not have any problem, as the lights did not stay permanently. Some times I drove the car for 35 KM but the indicators stay off
Guys please help me ....
Where can I find the diagnostic port on a 1995 Honda passport 3.2L
@phillip Small > By DOT specs, the OBD-2 connector has to be within 22 inches of the steering wheel. Center or edge, you decide. I can not speak for your 2009, but the center console on Honda’s mini-van, was on the right side of the console behind a plastic door. It is 22” but a the crow flies. A flash light and a good look around will locate it, they are all shaped the same and have 16 terminals. It could be next to the fuse relay center on the side of the dash, just turned sideways. It is June 2021, hope you have found it by now! Best of luck. Isuzu Master Tech, ASE Master Tech since 1978 - Retired.