How To Install Our 20x20 with Shade - Seven Peaks Fence And Barn
Вставка
- Опубліковано 11 лип 2021
- This is our DIY 20x20 horse stall with a 10x20 shade. Super easy to install and affordable! Watch how easy it is!
20x20 Stall With Shade Kit Instructions
1️⃣ Step 1: Attach each shade post (4) to the panels using panel clamps provided (14) going from the panel to the post.
- Set up 1 panel on each side and the 2 back panels with a post on each corner to get started.
- Make sure the L piece on the top of the posts are facing inwards towards each other.
2️⃣ Step 2: Attach front and back Truss to the posts using panel clamps provided (12).
- The truss will rest on top of post and on the Horizontal L Piece.
3️⃣ Step 3: Make sure all clamps are tightened before moving forward to next step.
4️⃣ Step 4: Make sure structure is square and adjust if needed.
5️⃣ Step 5: Attach the middle support using screws provided (4 Framing Screws)
6️⃣ Step 6: Attach 1 side support using screws provided (4 Framing Screws)
7️⃣ Step 7: Attach 1 cross support using screws provided (4 Framing Screws)
8️⃣ Step 8: Attach other side support using screws provided (4 Framing Screws)
9️⃣ Step 9: Turn last cross support upside down and attach using screws provided (4 Framing Screws)
🔟 Step 10: Make sure all screws are in place before moving forward to next step.
1️⃣1️⃣Step 11: Attach tin (7 pieces) to the framed roof using screws provided (60 Framing Screws)
Make sure to overlap the first 6 pieces of tin by 1 ridge and the last one by 2 ridges.
Be sure to use 3 framing screws on the front, middle and back of each piece of tin before going to next piece.
You can also use the thicker tin to tin screws to connect the overlapping tin.
1️⃣2️⃣ Step 12: Finish setting up the additional panels (4) to complete the stall using panel clamps provided (10)
1️⃣3️⃣ Step 13: Be sure to add an additional post on each corner for extra support and securing it into the ground using panel clamps by concreting it 2-3ft into the ground.
1️⃣4️⃣ Step 14: All Finished! Enjoy!
**NOTE**
**** BE SURE TO ANCHOR EACH CORNER OF THE SHADE USING POSTS AND SECURING THEM INTO THE GROUND WITH CONCRETE 2-3 FEET INTO THE GROUND.
****THESE SHADES ARE DESIGNED FOR OUR 20X20 STALLS AND ARE NOT INTENDED FOR ANY OTHER USE OTHER THAN WITH OUR PANELS.
**** ANY STRUCTURE OVER 200 SQ FEET IS REQUIRED TO GET A PERMIT FROM MOST CITIES IN THE STATE OF ARIZONA. CHECK WITH YOUR CITY FOR PROPER PERMITS AND REQUIREMENTS.
MATERIAL INCLUDED WITH 20x20 STALL WITH SHADE:
4 - 1 5/8" Shade Posts
4 - 2 3/8" Securing Posts
2 - Trusses
5 - (2) Side / (1) Middle Frame Pieces / (2) Center
7 - Tin Pieces
7 - Panels
1 - Panel/Gate Combo
36 - 1 5/8" Panel Clamps
8 - 1 5/8" x 2 3/8" Adapter Clamps
4 - 2 3/8" Round Plastic Post Caps
100 - Framing Screws
40 - Tin to Tin Screws
⚒️ Tools:
2 Ladders: amzn.to/3ACY6vE
Socket Adapter - amzn.to/2OZTWJb
9/16" Socket - amzn.to/3womjCK
5/16" Chuck Driver - amzn.to/36jXtJD
Impact Drill - amzn.to/2MKkb3m
Gloves - amzn.to/2qcUn8m
1 5/8" Panel Clamps - sevenpeaksproducts.com/produc...
1 5/8" x 2 3/8" Adapter Clamps - sevenpeaksproducts.com/produc...
⚡PURCHASE ONE OF THESE SHADE KITS TODAY!
👉 www.sevenpeaksfenceandbarn.co...
Delivery and financing available!
Visit us at our locations or give us a call:⬇️
Texas Location:
📍 9601 County Road 1004 Godley, TX 76044
📱: 817-398-5029
Arizona Location:
📍 1037 South Center Street Mesa, AZ 85210
📱: 480-246-6237
🗣️ Be Sure To Follow Us On Our Social Media Accounts:
Facebook - / sevenpeaksfenceandbarn
Instagram - sevenpeaksf... - Домашні улюбленці та дикі тварини
Would be nice to see how you dug those extra 4 post hole in the corners for cementing them in.
We've dug them by hand, we've also used an auger bit with a tractor or a little 2 man auger. We also just tested out a post driver for those post on the corner that you can buy on Amazon or even rent one from home depot or a local tool rental in your area. Here is video showing how that worked ua-cam.com/video/5Nrf9v4NAcU/v-deo.html
The Music is unnecessary and distracting. I can’t hear you! But other than that good job!
Thank you very detailed.
No problem! Thank YOU!
What measurement should it be when your checking square? 20 ft? I have the same kit
Lose the annoying and distracting music. It is hard to discern what is being said.
Ugh! Agreed! Zero music needed in instructional videos.
Note taken! Thank you for the input! Sorry about that we are working on getting better and unfortunately did not have a mic for this video... Agreed the music is too loud but once you get into the detailed step by step the camera is closer and you can hear better.
@@lakefamilyfarmaz4437 Note taken! Thank you for the input! Sorry about that we are working on getting better and unfortunately did not have a mic for this video... Agreed the music is too loud but once you get into the detailed step by step the camera is closer and you can hear better.
How much are the 10x10 shades
Our 10x20 stall out of our 4 rail standard panels with a 10x10 shade is currently $1400 + Tax. All of our products and accurate pricing can be found on our website at www.sevenpeaksfenceandbarn.com
For the sheep shade any way yall can make the shade sit lower. At least 6ft tall. Sheep arent that tall and would be good to add some sheet metal panels to the back and sides of the shade. To protect herd from wind and element and even predators.
Why do you need to put music into your how to video. I can hardly make out what you are saying.
Try another computer or way to watch it. I can understand what they're saying just fine.
I can hear what they’re saying mostly but it’s so irritating.
Note taken! Thank you for the input! Sorry about that we are working on getting better and unfortunately did not have a mic for this video... Agreed the music is too loud but once you get into the detailed step by step the camera is closer and you can hear better.
@@JanetOrt sorry about that we are working on getting better. Thank you for your input!