Help support the channel and become a channel member for only $0.99 a month. Get access to new videos before they are published. ua-cam.com/channels/nR5pkDn0nx5odujIgmwHKg.htmljoin
I Am getting one. To Melt 🫠 my copper, brass, aluminum, and so on. I have looked for a video on melting brass without flux can't find anything so u may give it a shot with and without. But thanks for the walkthrough 😃 now i know what to look forward to.
That's great! Definitely get new crucible tongs or make your own like I have in the video. I have a few videos coming out in the next few weeks where I melted brass. With a smaller furnace. I didn't use any flux.
Well that I don't know, but You really only need 2 burners for forging. As you can see in the video once, I heated it up I turned off the second burner.
nope! I have added an IR Refractory coating which helps retain the heat. I'm not sure if it's necessary. However adding the rigidizer is very important due to the harmful fibers that you may breath in.
for the price, may have to pick one up down the road, but not sure I need yet another one around, but would be nice having a light one vs the 5000 pound one I have now :)
"Because this is a brand new crucible, I'm going to heat it up very slowly"... Immediately proceeds to heats it up very fast. FYI a slow 'proper heat' of a new crucible (according to e.g. manufacturers of "Mammut crucibles") should take about 2 hours to slowly ramp up to reach 200°C. Then it will have been safely dried and you can go nuts. A kiln or an oven is better suited for this than a gas furnace.
Yeah I only had the burner half open. It definitely heated up much faster than I would have liked. I usually put it in my house hold oven for 1hr. It worked out well in the video though, no issues. I've already used it a number of times since.
@@HeinrichsMade good to know. the cost of propane has been the hold up with me getting or building a melting furnace. i would use a waste oil burner if i wasnt in a residential area.
@@HeinrichsMade i havent bought propane in forever and a day, i fill my tanks at work for free. and my grill is hooked up to the NG off my house... but since washington has one of the highest gas taxes in the country i'm pretty sure its not cheap.
Yeah buddy! I'll be using this for most of my videos now. I can pour more than 1 thing. Yeah I'd say it's as big as yours. It looks like it could fit a larger crucible as well.
If I left it in there longer I know it would have gotten there. Also, don't forget it is a large diameter furnace. Maybe bringing the steel higher and closer to the foam would heat it quicker.
If you’re referring to how hot the crucible and metal got, don’t forget that directly sunlight makes it look not as hot. Any knife maker will tell you they have at least once overheated a blade prior to quenching because they were in direct sunlight and miscalculated how hot their material was
@@rickytickybobbywobbin055 True, but I've done some blacksmithing in the sun. So I have that point of comparison, and our sad barely adequate homemade forge did at least that good.
@ fair enough. Could it be because of how large the furnace is compared to the small work piece? From what I understand, larger forges/furnaces are much less efficient with smaller pieces like that
@@rickytickybobbywobbin055 Probably. It's optimized for a crucible, not a small piece of steel, so it really isn't that great of a forge. That's what I was thinking when I first saw the video.
Help support the channel and become a channel member for only $0.99 a month. Get access to new videos before they are published.
ua-cam.com/channels/nR5pkDn0nx5odujIgmwHKg.htmljoin
Awesome video! This vevor furnace seems really good.
Thank you 👍
I Am getting one. To Melt 🫠 my copper, brass, aluminum, and so on. I have looked for a video on melting brass without flux can't find anything so u may give it a shot with and without. But thanks for the walkthrough 😃 now i know what to look forward to.
That's great! Definitely get new crucible tongs or make your own like I have in the video. I have a few videos coming out in the next few weeks where I melted brass. With a smaller furnace. I didn't use any flux.
8:12 nice to know one gas line can turn off
Nice. I have put some thought into getting a 2 burner. Wonder what the difference in gas use is compared to how fast everything melts
Well that I don't know, but You really only need 2 burners for forging. As you can see in the video once, I heated it up I turned off the second burner.
so u add rigidizer from the stray bottle but you dont also add another layer of refractory cement? i see it done both ways
nope! I have added an IR Refractory coating which helps retain the heat. I'm not sure if it's necessary. However adding the rigidizer is very important due to the harmful fibers that you may breath in.
for the price, may have to pick one up down the road, but not sure I need yet another one around, but would be nice having a light one vs the 5000 pound one I have now :)
Yeah it's SUPER CHEAP!!! It's huge and light weight. It definitely beats a 5000 pound furnace 😂
Can you melt glass in this too?
I'm not sure.. I've never melted glass. So far I have gotten this furnace to 2000F
"Because this is a brand new crucible, I'm going to heat it up very slowly"... Immediately proceeds to heats it up very fast.
FYI a slow 'proper heat' of a new crucible (according to e.g. manufacturers of "Mammut crucibles") should take about 2 hours to slowly ramp up to reach 200°C. Then it will have been safely dried and you can go nuts. A kiln or an oven is better suited for this than a gas furnace.
Yeah I only had the burner half open. It definitely heated up much faster than I would have liked. I usually put it in my house hold oven for 1hr. It worked out well in the video though, no issues. I've already used it a number of times since.
how much LP gas did you burn to melt that.
Not much... I don't measure how much I use. I just know that 20lbs of LP gas lasted me over a month using it.
@@HeinrichsMade good to know. the cost of propane has been the hold up with me getting or building a melting furnace. i would use a waste oil burner if i wasnt in a residential area.
@@theoriginalDirtybill how much does LP cost? A 20lb tank costs me $22 to fill
@@HeinrichsMade i havent bought propane in forever and a day, i fill my tanks at work for free. and my grill is hooked up to the NG off my house... but since washington has one of the highest gas taxes in the country i'm pretty sure its not cheap.
@@theoriginalDirtybill oh that's sweet! If you fill your tanks up for free at work get melting 💥💥💥💥 haha
nice setup. big enough for me even lol
Yeah buddy! I'll be using this for most of my videos now. I can pour more than 1 thing. Yeah I'd say it's as big as yours. It looks like it could fit a larger crucible as well.
My burner and valves dont line up lol
Lol what? Maybe switch them around
The forge setting honestly seemed rather unimpressive, I expected better than that dull red.
If I left it in there longer I know it would have gotten there. Also, don't forget it is a large diameter furnace. Maybe bringing the steel higher and closer to the foam would heat it quicker.
If you’re referring to how hot the crucible and metal got, don’t forget that directly sunlight makes it look not as hot. Any knife maker will tell you they have at least once overheated a blade prior to quenching because they were in direct sunlight and miscalculated how hot their material was
@@rickytickybobbywobbin055 True, but I've done some blacksmithing in the sun. So I have that point of comparison, and our sad barely adequate homemade forge did at least that good.
@ fair enough. Could it be because of how large the furnace is compared to the small work piece? From what I understand, larger forges/furnaces are much less efficient with smaller pieces like that
@@rickytickybobbywobbin055 Probably. It's optimized for a crucible, not a small piece of steel, so it really isn't that great of a forge. That's what I was thinking when I first saw the video.
How to get a job in this company please reply me
I don't know, I don't work for this company
Say no to ASMR
Whattt?