Girth Gear Reversal : IN PROGRESS PART FOUR (Measuring Root Clearance)

Поділитися
Вставка
  • Опубліковано 29 жов 2024

КОМЕНТАРІ • 25

  • @gopaldas-cp2yn
    @gopaldas-cp2yn 3 роки тому +3

    Can you share the information regarding General rule for
    1.kiln girth gear and pinion permissible of root gap, backlash , radial run-out, axial run-out.
    2. Ball mill gear and pinion permissible of root gap, backlash , radial run-out, axial run-out.
    3. Kiln shell radial run-out, axial run-out.
    I will be very thankful for that. 🙏

  • @danielsuas9095
    @danielsuas9095 4 роки тому +2

    Do you have any videos on how the floating tyres get assembled? thanks

  • @johnnydas3735
    @johnnydas3735 5 років тому +2

    How can I know that if the girth gear module is 50 then what should be the the backlash clearance and root as well...?

  • @mamtavishwakarma3027
    @mamtavishwakarma3027 3 роки тому +1

    बहुत ही सुंदर

  • @mdsadhiq1234
    @mdsadhiq1234 6 років тому +3

    I appreciate your efforts

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  6 років тому

      Thank you very much for your appreciation, it motivates me to make more and more videos 😊

    • @rajeshpatra4700
      @rajeshpatra4700 5 років тому +1

      need some help about this alignment. ??

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  3 роки тому

      Let me know what help you need

  • @devshastr
    @devshastr 5 місяців тому

    What reason killn girth gear out of centre in killn sheell

  • @9030407277
    @9030407277 6 років тому +2

    Can you please make a video about "what do you do if the root clearance is way beyond the permissible limit?". Thank you

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  6 років тому

      kiri sure, I will try to cover this topic as soon as possible, thank you 😊

  • @k.Shubham
    @k.Shubham 3 роки тому

    Is this gear casted or made by other process

  • @JCLcol24
    @JCLcol24 3 роки тому +1

    That chair will be removed or remain as it is after the installation?

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  3 роки тому +1

      It is removed after installation; they are termed as Girth Gear alignment fixtures

  • @smorsch
    @smorsch 5 років тому

    I think there is a gap in the gear mesh, Gears are not 100% parallel, unless the finishing is so bad that the gears are curved?!
    in other words the backlash is not the same on both sides and the pressure point or the touching surfaces are not really touching on both sides (there is a gap it's not ZERO) ?!

  • @santoshrathod1244
    @santoshrathod1244 4 роки тому

    Sir plz tell me how to change girth gear felt

  • @vivekpandey841
    @vivekpandey841 5 років тому

    Gearth gear ka clearance ketna rakhte hai

  • @pareshahir3422
    @pareshahir3422 5 років тому

    Pinion to ring gear ruth gaph to breakless kitna mm rakh 8 ya 10

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  5 років тому

      Kya aap Module bata sakte ho????

    • @mangeshk6515
      @mangeshk6515 4 роки тому

      @@GlobeTrotterJAY hi
      Please can you tell me...If we are getting backlash at certain position very low i.e. 0.2 to 0.4 in cold conditions of kiln in both pinion,and in hot we are getting more than 5 in this case any pinion adjustment required?
      Module is 45 and during static inspection we observed pittings in certain set of tooth flanks

  • @lalchandrasharma1230
    @lalchandrasharma1230 4 роки тому

    Root backless and girth gear alignment ke bare mein information Kijiye sir

  • @abdelhakmaamar7223
    @abdelhakmaamar7223 3 місяці тому

    La synchronisation de denture pignon. D attaque et couronne c'est très precis

  • @baibhavsharan6519
    @baibhavsharan6519 4 роки тому

    How much clearance permissible

    • @GlobeTrotterJAY
      @GlobeTrotterJAY  3 роки тому

      To simplify for a spur gear it's around 25% of the module in cold condition

  • @vivekpandey841
    @vivekpandey841 4 роки тому

    Sir clearance kya rhta hai