Собрал схему, ай крутится, какие пора метры имеет тво блок, ток холостого хода, ток под нагрузкой, напряжение, где все это, умелые ручки что не сидели от скуки, молодец.
It,s not working i try 3 times closely folow the instructions on the video but not working and it burn the mosfets so this is a fake or creator is hiding something.
@@СергейВасильев-е2ь no it’s simply bc this is a scam. Those are mosfets they require a minimum voltage rating to turn it off, and it has to go over that voltage rating to turn it on. Those are diode and resistors the diodes control. The directions of the flow of electricity resistors increase or decrease the resistance of electricity when he runs power through that nothing will happen if anything, the Mosfects will melt and destroy itself and if your trying to make esc look at the data sheet it tells you how those mosfets can be used no exceptions these also require gate drivers and that two has a data sheet.
Hello what is the right connection of diode's? In your film three bottom diodes are connected to the gates of mosfets, and between 3:42-3:57 two of them are connected to Drain of Mosfets? In my opinion connection to the gates doesn't work properly with 3 wires bldc motors?
Hey this is a scam. Those are mosfets they require a minimum voltage rating to turn it off, and it has to go over that voltage rating to turn it on. Those are diode and resistors the diodes control. The directions of the flow of electricity resistors increase or decrease the resistance of electricity when he runs power through that nothing will happen if anything, the Mosfects will melt and destroy itself
without capacitors in the circuit the wave generated will be very noisey. and in real world applications would probably damage the motor. don't you think it's about time you made propper circuit's on proper circuits boards .
Of course cannot work... This is bs You cannot supply the montage through a 1M resistor and gate.. The + is on the star connection ( neutral point ) ☝️
До этого видео собирал подобную схему. Не заработала но если надо мне подумать над ней. Однако если убрать диоды то нужно будет подтолкнуть движок для, запуска.
@@kabalvlad походу вся схема это косяк. Собрал в точности не заработала. Движок просто фиксируется а одном месте. Даже если крутить. Косяки у него были, когда припаяные диоды те что на низу были один на затвор два на сток. Ну корлче один крайняя нога. И два средняя Потом он все перепаял на затвор. . Кажется Легче на ардуинке сделать. P. S. Использовал мосфеты с материки. Ubd: 09.05.25 P. S. S. нашёл видео где чел разбирает схему, по сути надо затачивать схему под мотор индивидуально схема работает не со всеми моторами. короче проще не извращаться а купить готовый контроллер За 500 рублей на али и не морочить голову.
Çok mantıklı değil. Sebep: BLDC motorlar kutuplarını bilmesi gerekir; videoda dikkat ederseniz motor durmuyor ve İLK HAREKET (first move !!!!) bu işe yaramaz bir devredir. Bu kadar kolay olsaydı işimiz çok rahattı. Ancak; ilk hareket verilirken motorun hangi konumda olması gerektiğni cihaz bilmelidir! okey
Bro u r hiding too much thing's in this video, like motor starting torque, motor speed, and voltage and current. And also motor speed not enough for propellers. 😊😊😊
I liked your project, thx.
Glad to hear that!
Muito bom, parabéns eu também monto projetos aqui no UA-cam.
How many voltage given to circuit
fine work and chose mosft z44 all scrit very good l we need more Amper make tow mosft
Can I use A2212/6T 2200 KV Motor ? else please guide for any alteration
5:10 Did you have to start it by hand, I see a break in the video where I think you might have done that?
Beautiful work
Meus parabens amigo ficou shom👏👏👏👍
Thank you very much my friend. How can I control the brushless motor of the gimbal?
with this design instead of gimbal you obtain a kebab maker putting dishes of meat , be careful never use conductive sauces water based
How much input?
Good video❤❤
How it works without 3 fase pulse generator?
Hello, how much voltage does this circuit withstand?
Good 💯
Bro please suggest can I use 10k resistance in (half watt) ????
Hello 👋
Can I use z44 mosfet?
Yes absolutely you can use
…
Can I Test Electric scooter Bldc motor?
Yes
How to change direction
Porquê em 3:47 do vídeo você mudou o projeto? Os dois diodos pularam de posição, para quê?
Собрал схему, ай крутится, какие пора метры имеет тво блок, ток холостого хода, ток под нагрузкой, напряжение, где все это, умелые ручки что не сидели от скуки, молодец.
Hi Creative Techos did you solder 1M resistor on a second leg of a irfz or the first leg of irfz?
How does it work
Ese circuito podría hacer funcionar un alternador combertido en motor brusler?
Can i used this circuit BLDC 12 volt triple phase cylling fan ?
This circuit works only for wire connections common wire is necessary
I make the circuit but not working, can you explain if you like how to do right?.
@@dejanpetkovski8761 dont't waste time with this scheme
مافائدة العازل البلاستيك اذا البرغي وصل بين الموسفيت والألمنيوم
البرغي ماوصل الى الالومنيوم فقط مثبت على سطح الموسفت
Amazing 😊
Great content
What's power ?
Circuit not working bro 😂
Use separate heat sink, or use thermal tape.
Bro did you Build it
Use fr diode
Really??
Отлично!
Stop and start 😂
💖👍
there was a mega ohm resistor which i didnt get where you soldered
Volt ?
It,s not working i try 3 times closely folow the instructions on the video but not working and it burn the mosfets so this is a fake or creator is hiding something.
Tienes que desarmar el motor y encontrar la conexión central del bobinado en estrella y conectarla al positivo...
@@joaquintoro497I do that but same case motor not running..
Здесь в комментариях написали, что диоды не одинаково соединены. Возможно по этому у вас схема не заработала
Fake
@@СергейВасильев-е2ь no it’s simply bc this is a scam. Those are mosfets they require a minimum voltage rating to turn it off, and it has to go over that voltage rating to turn it on. Those are diode and resistors the diodes control. The directions of the flow of electricity resistors increase or decrease the resistance of electricity when he runs power through that nothing will happen if anything, the Mosfects will melt and destroy itself and if your trying to make esc look at the data sheet it tells you how those mosfets can be used no exceptions these also require gate drivers and that two has a data sheet.
안녕하세요.
50~70V200A 만들어 보세요.❤
50~70V200A 만들어 보세요.😊
Run hub motor which has hall senser 😊
Hello, what is the 1mega ohm resistor for?Will it work on irzf 44n - it doesn't work for me and I connected everything the same way
fake
Use 1 k
Если регулятор 100 Амперный, то почему испытание производите на игрушках?
Bleah man
Hello what is the right connection of diode's? In your film three bottom diodes are connected to the gates of mosfets, and between 3:42-3:57 two of them are connected to Drain of Mosfets? In my opinion connection to the gates doesn't work properly with 3 wires bldc motors?
Why to use many component ? only irfz44n & one 10k Pot resistance is enough to control 12 DC motor without Heatsink.
Bad videos not much enough information about voltage ⚡
Manque quand même le minimum gaz et l’arrêt
i cannot brain the circuit diagram.
Guys i need to bldc controller circuit diagram 12 to 36 volt with video
make sure 100%working after giving me
कैसे गुपचुप से रहता है? काम कर दिखाना न तो चाहता है लेकिन मुंह में दही जमा रखे है, या बोलने मे शर्म आती है, इससे अच्छा चूड़ी पहन कर बैठै जाओ |
I followed your vedio exactally and it does not work, then I looked at you schematic and it was different, definatly a NOGO😮💨
Tienes que desarmar el motor y encontrar la conexión central del bobinado en estrella y conectarla al positivo...
Hey this is a scam. Those are mosfets they require a minimum voltage rating to turn it off, and it has to go over that voltage rating to turn it on. Those are diode and resistors the diodes control. The directions of the flow of electricity resistors increase or decrease the resistance of electricity when he runs power through that nothing will happen if anything, the Mosfects will melt and destroy itself
ua-cam.com/users/shortst-GhxdOinoA?si=MB7LSWQ0pztChcxI
Bro I am see more your videos so can are help. I have 4 wire stepper motor can are up load above motor dirver circuit diagram me 🎉
Is is IRF3205
como se si funciona
don't work
How to run hard disc motor by this circuit
without capacitors in the circuit the wave generated will be very noisey. and in real world applications would probably damage the motor. don't you think it's about time you made propper circuit's on proper circuits boards .
Boss super boss how to makeup U V W TESTER please makeing
one video boss
IRFZ44N ????????????
اخي العزيز الدار لم تشتغل معي
Hi, I design BLDC/PMSM drives for a living. Kindly do not do this.
No funciona
Muchas gracias
Lo realice igual y no sirve
make + from common then it will works i tried ad ok
В этих двигателях нет общего контакта@@gn-ne1ed
Tienes que desarmar el motor y encontrar la conexión central del bobinado en estrella y conectarla al positivo...
@@gn-ne1edهل تعمل تلك الدائرة لقد جربتها ولم تعمل
Проверил ,не работает. Сгорели мосфеты и ничего больше
Of course cannot work...
This is bs
You cannot supply the montage through a 1M resistor and gate..
The + is on the star connection ( neutral point ) ☝️
😊😊😊
ha ha ha 100 A ??? originál psychiatria....
irf 3205 or irfz 44 ...??? 100 A x 50 V = 5000 W ( 5 kW ) !!!
Ни чего не работает.
Он допустил косяки в схеме, в конце видео он исправил их.
До этого видео собирал подобную схему. Не заработала но если надо мне подумать над ней.
Однако если убрать диоды то нужно будет подтолкнуть движок для, запуска.
@@FIL_KILLER что за косяки ?
@@kabalvlad походу вся схема это косяк.
Собрал в точности не заработала.
Движок просто фиксируется а одном месте.
Даже если крутить.
Косяки у него были, когда припаяные диоды те что на низу были один на затвор два на сток.
Ну корлче один крайняя нога. И два средняя
Потом он все перепаял на затвор. .
Кажется Легче на ардуинке сделать.
P. S. Использовал мосфеты с материки.
Ubd: 09.05.25
P. S. S. нашёл видео где чел разбирает схему, по сути надо затачивать схему под мотор индивидуально схема работает не со всеми моторами. короче проще не извращаться а купить готовый контроллер За 500 рублей на али и не морочить голову.
Amigos, esse projeto é falso.
Dude that's not irfz34n lmfao wtf
You can you irf3205 or z44n
Este video es una estafa, no funciona , es mentira deberían quitarle el canal a creadores de contenido falso como este
tienes que desarmar el motor y encontrar la conección central del bobinado en estrella y conectarla al positivo...
+1
Çok mantıklı değil. Sebep: BLDC motorlar kutuplarını bilmesi gerekir; videoda dikkat ederseniz motor durmuyor ve İLK HAREKET (first move !!!!) bu işe yaramaz bir devredir. Bu kadar kolay olsaydı işimiz çok rahattı. Ancak; ilk hareket verilirken motorun hangi konumda olması gerektiğni cihaz bilmelidir! okey
Fake .i tried several times not working
A successful project. Can I communicate with you through any means you like?
Seems fake
To much fake
Menteur
少電源的儲能電感
Where is the mosfet no
3205
irfz44n mosfet
انصح الجميع هذة دائرة وهميه لاتعمل جربتها ثلاث مرات حرام عليك تضيع من وقتنا ايها النصاب
Bro u r hiding too much thing's in this video, like motor starting torque, motor speed, and voltage and current. And also motor speed not enough for propellers. 😊😊😊