Acura/Honda Power Steering Hose O-ring Replacement

We have a leak on the pressure line for the power steering pump. It's only at the seal, so we are replacing the O-rings on both lines going to the pump.
Check it out.
#techreviewbyirdi #acura #honda

[@khashcpt]

Nice video thank you , I’d like to always lubricate the O rings before after installing,in this case some power steering fluid does the job

[@ahyungrocks5509]

Great video. Will do the same for our Odyssey.

[@gigigoallaround5044]

Thank you for making this video it really helps me alot

[@TechReviewbyIrdi]

Dormans is 926-157. They can be checked at any parts store for other manufacturers.

[@jimmyjazz78]

I wish I'd watched your video (and not done mine in dim lighting). I didn't realize the inlet was plastic and stripped the back threads. I didn't think to check torque, only went with feel on tightness with a socket. No leak so far, but any suggestions on dealing with the stripped threads since I can't actually tighten the bolt now? I can use loctite to keep it in place, but that's it. Again, the front one was tight but didn't break.
Thanks if you have time to reply!

[@TechReviewbyIrdi]

There's not much in pressure, use RED Loctite. It will withstand the heat by the engine. If you need to pull it out later, you can use an heater gun to warm it or hair dryer on hot to loosen the red loctite. I've done it before. Your good.

[@jimmyjazz78]

@@TechReviewbyIrdi Thanks for reply, I will give that a shot!!!

[@user-px5he2np5u]

Mine is leaking so it's the seal?? Thanks for helping

[@TechReviewbyIrdi]

Usually. The fluid over time as well as heat shrink the seals enough to leak.

[@djizzy12]

What are the part numbers for the O rings?

[@derrickmitchell3770]

What size is the bolt that's on the return hose connector?

[@TechReviewbyIrdi]

I believe 10mm

[@B.jaasmin]

I Follow the instructions and my Acura rl still has the whining noice and the fluid pump it’s bubbling I’m not sure what it can be ?

[@TechReviewbyIrdi]

It's the pump itself. If the bearing housing is going, it will sound like that as well. It will churn the fluid to make it bubble as well.

[@josedaniel9656]

Hey boss did you keep the top on the reservoir

[@TechReviewbyIrdi]

I did. You can take it off, but it can get messy.

[@josedaniel9656]

@@TechReviewbyIrdi thank you brother 🙏

[@anthonygeraghty]

hi my name is anthony i have seat leon 2006 have eltic power stering red light has come on tryed every thing to remove stering is working fine no probleam what u think might be probleam thanks

[@TechReviewbyIrdi]

Could be the sensor on the fill under the reservoir. That can be faulty as well.

[@anthonygeraghty]

thanks for replying but it eletric power not fluid it has tracion control asisted power sering power to sterring is working fine would it be falty abs rings

[@Sapphonic]

did you empty the power steering fluid resevoir before starting?

[@TechReviewbyIrdi]

Mostly. I used a pump/air unit, off amazon. I used for a lot of fluid drawls. But I didn't need to take a lot out. Just a little. The rings are higher.

[@pwcstatenet7515]

I was hoping this question was asked

[@user-ve9uj3fr5q]

no

[@user-tn4uu6zj2x]

Horrible video bro your going too fast

[@TechReviewbyIrdi]

Sorry for that. It was between jobs and I wasn't happy either. I'll do better.

[@RP4886]

Video is perfect. Its such a simple job, only need to know which color goes where. The rest is very self explanatory once you look at the pump

[@Ice88911]

All you can do is laugh. He points to items while he has things (o-ring package) in the way so you can't see, Then he shows you items off screen. He also tells you to remove a bracket that is no longer there.