ROCAM ECU Series - The Cluster self test

Поділитися
Вставка
  • Опубліковано 27 вер 2024
  • This is a short video on how to do a cluster self test, and what the various codes mean. If you would like more details, leave a comment!
    Produced by ‪@KingdomDigitalServices‬

КОМЕНТАРІ • 12

  • @pcmanser5186
    @pcmanser5186 4 місяці тому +1

    Brilliant

  • @uwuking9914
    @uwuking9914 8 місяців тому +4

    Thanx DAVE we been waiting a long time for videos like these in South Africa.We need more local help and information on SA vehicles.A lot of videos on overseas markets but very little local.Keep them coming.Dave Knapp from Mpumalanga

    • @Shay4Shan20
      @Shay4Shan20 22 дні тому

      Thank you. I really been searching so hard Dave. I await for more videos

  • @ysabel014
    @ysabel014 5 місяців тому +1

    Hi Dave. Just wanted to ask, if the immobiliser warning light doesn't flash anymore, what could the problem be? Car is cranking, there is fuel but no spark

    • @davehamlyn3097
      @davehamlyn3097 5 місяців тому

      Does the PATS LED still work ? Has the Immobilizer been bypassed ? Do you still have the key reader in ? Check for a short circuit in the starter relay or the started relay has been grounder out.

  • @iLoved-iPhone
    @iLoved-iPhone Місяць тому +1

    Thanks so much for this Dave! . Ive got 330k on my lil fiesta and never knew about this. Having said that. i have had to get the ECU repaired. And just now did my head gasket after some overheating problem although it appears it was just a failing water pump so it was probably unnecessary to do the whole head etc... although i do notice improved performance now. Another problem has arisen though. The speedo and odo are not working....I went through the tests as you have indicated...but well not even sure what to look out for... Any idea would be really helpful and grateful! . Thank you . Laurence

    • @davehamlyn3097
      @davehamlyn3097 Місяць тому

      Check the Speed sensor harness where it plugs into the Transmission. On the harness there are three wires at the connector. The violet wire is to the Power Hold relay. Chech that these wires have not shorted out or are not broken

    • @iLoved-iPhone
      @iLoved-iPhone Місяць тому

      @@davehamlyn3097 You legend thank you will check that and let you know!

  • @janbotha6394
    @janbotha6394 8 місяців тому +1

    Interesting!
    Bantam starts first time, misses intermittently, stutters and then... sometimes run 100% and goes like a well oiled... Bantam
    Slow moving traffic... stuttered, died, towed, 2 hours later, started but kept on stuttering...
    1.3L 161k km... fairly new coil pack
    Do the injectors need maintenance of any kind?

    • @davehamlyn3097
      @davehamlyn3097 8 місяців тому +1

      No, Injectors dont need maintenance. The the HT leads and the spark plugs in the Rocam engines 2002 to 2007 should be set at 1.00mm and from 2008 to 2012 at 1.3mm. Check also the three pin connector at the harness thgat plugs into the coil. There could be an open circuit right on the connector plug. If it switches off and does not crank, keep an eye on the Immobilizer warning light. Tjhis could also be the computer box that needs repair .(Had a few of these)

    • @xaviersandrinedemay6396
      @xaviersandrinedemay6396 4 місяці тому +1

      Clean PCV and Idle control valve. Test cranckshaft speed sensor

    • @janbotha6394
      @janbotha6394 4 місяці тому +1

      @@xaviersandrinedemay6396 Thank you!
      Turned out to be fuel pressure regulator... got stuck somehow and flooded the motor... sorted now R180.00 later...