Honda Accord Fuel Injector Change - 1.5T Engine with Rough Idle - Accord Injectors
Вставка
- Опубліковано 10 лип 2024
- 0:00 Welcome
00:37 Parts needed to swap Injectors
01:57 TLDR on the Injector Swap
03:25 Relieve fuel pressure
04:45 Remove battery
05:58 Remove hoses
07:11 Remove piping
08:12 Remove bracket
09:20 Remove Intake manifold connections
10:10 Loosen throttle body
11:39 Disconnect fuel line
12:37 Remove Intake manifold
16:22 Remove heat shield
16:43 Fuel rail removal
20:14 Fuel injector removal
21:41 New parts
22:34 Fuel rail prep
25:00 Installing the new injectors & fuel rail
28:34 Intake manifold prep
29:20 Intake manifold install
30:19 Throttle body install
34:15 Battery install
My other video:
• Honda Accord Rough Idl...
A different video showing how to swap Honda Accord Fuel Injectors:
• How to replace injecto...
Video showing how to clean carbon build up off of valves:
• How To Clean Carbon Of...
BoostedFilms Website
www.boostedfilms.com
My Amazon Store
www.amazon.com/shop/boostedfilms (paid link) #ad
Disclaimer: This video is for entertainment purposes only! Perform anything you see in this video at your own risk. Due to factors beyond the control of this video creator, I cannot guarantee against improper use or unauthorized modifications of this information. Boosted Films assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Boosted Films, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Boosted Films. - Авто та транспорт
pro tip: if you remove the metal base plate underneath the battery tray (5 bolts)with a long extension you can easily get to the pesky bolt you're talking about that holds the small fuel pipe on
Thank you so much. Helped so much and saved me alot of money.
Plenty details, excellent video. Too bad we all can’t show how we struggle while working.😂
Thank you very much for this video, I just completed injectors, manifold gaskets, throttle body gasket on my 2019 accord 1.5T Sport. Even with my intense automotive skills, it still took me about 7 hours to complete; however, your video was on point
Great job!!! 👍 This tutorial was excellent!!! Happy Easter 😊
Great vid, thanks a bunch for the details! I've got a 2018 civic SI, mine was misfiring on cold start and ran very lean under any type of spirited throttle. I cleaned my injectors and replaced the fuel pump with a more powerful pump, since it has a recall on the Si. Worked exceedingly well! Definitely worth the time investment, fixed those issues and didnt have to pay the dealership a fortune. I do have a set of the new type of injectors from Honda on order, since they discontinued these garbage ones.
Oh yea, before you start it, if you turn the car to accessory mode 5-6 times, you'll build the fuel pressure up and wont have to crank it. :)
Great Video!! Helped out a lot for me. Changed the injectors on my 1.5T 2018 Honda CR-V and now it is running better than ever!! Also had the issue of going WOT and it’ll cut off the engine and I would get a blinking CEL.
Glad to hear!
WOT???
On point 👍
Amazing .... thank you very much ...
Welcome 😊
Run higher octane from now on, Honda recommended me this, i had the same issue, sucks the manual says 87 but that is not the case..
Hey your video is really helpful. I am replacing injectors on a 2014 Accord 2.4 L earth dreams, but nonetheless your guide still applies to steps that I must take as well.
I have a question about the fuel rail outlets for the injectors. I noticed you didn't really close up on them in your video before sitting the new injectors in them. But on my fuel rail there are O rings that I am wondering if I can get away with leaving them as is before I install my new injectors. I don't think you made any changes to those in your process unless tldw. Thanks, I appreciate any feedback!
Any advice on where to order injectors.. I went to local dealer to order was told they're on backorder with no ETA
The sensor on the end of the fuel rail. The one with the rubber connector over it. What color are the wires going into that plug, and in what order?
Should i order the parts from ebay? They have the old part numbers on it for the injectors and its way cheaper its around 100 but from an actual honda parts website it runs abt 4-600?
A 6 or 7 mm closed end wrench will slip over and compress the backside of the annoying wire connections.
One mechanic I know will connect a scanner to the car then take the car up a near by steep onramp in 1 st gear . The car will throw codes a couple of times then in most cases the injectors will clear out.
Hi how did you clean your intake runners, you mentioned in the video you had a video link in the comments on how you cleaned it up but I see nothing like that in the comments, can you share the link. Will appreciate
Thanks
Link is in the video description... Also here. ua-cam.com/video/LTV-uHv5Cwk/v-deo.html
what size is the bolt on the high pressure fuel line? 10mm?
Damn my car has 23k miles n its been having rough idles i think i need to replace my injectors as well is it normal to have to replace em this early on?
Where did you order your parts from? Honda dealer wants $670 for the injector kit. This is minus the gaskets.
was your oil diluted with gas ?
Did you ever figure out what was going on with the braking and shaking? I'm currently experiencing that as well as the Christmas lighting dashboard.
My car still does the little shake at stop lights. I would not worry about that part. But if your dash lights are on, something still needs to get fixed.
There is no need to change these injectors. They are perfectly washed on stands and checked. Test range 40-120 Bar. There is a microfilter at the inlet, it is advisable to replace it.
You can clean with machine right?
People do injector cleaning. But its typically for port injection. I'd recommend just buying new OEM. However if you get yours cleaned and it works, please let us know!
How long did this job take you? I would say im really mechanically inclined.
I would just start early and plan for it to take a full day.
How many miles does your car have when you did this job ? Sorry if I missed it
Just over 100,000 miles
Awesome I hope I don’t run into this problem. I have the same car. But mine has only 40k 2018 year it’ll take me another 7+ years to get to that amount of miles lol
Can i pay you to do mine?
Direct injection is such a pita
can u buy injectors from auto zone ?
Where did you order your parts from? Honda dealer wants $670 for the injector kit. This is minus the gaskets.