How to make 4x4 wireless Roborace Robot using Flysky and Brushed ESC
Вставка
- Опубліковано 30 вер 2024
- Components:
1. Flysky fs-i6 Tx Rx: www.flyrobo.in...
or
amzn.to/4em7acn
2.Brushed ESC: amzn.to/45q9jiZ
or
www.flyrobo.in...
3. 500 rpm Johnson gear motor : amzn.to/3jDnrlq
4. Plastic robot wheels : amzn.to/3WpLP8q
5. Motor Clamps : amzn.to/3Wvfn4r
6. Battery : amzn.to/4fjtd3V
*-*-*-*-*-*
4x4 Roborace Robot using Arduino and BTS7960 [without Brushed ESC] : • Roborace Robot using A...
#DIY#RCcar#techathome
Music used:
Song: LiQWYD - Summer Nights (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • LiQWYD - Summer Nights...
Xtasy by Lahar / musicbylahar
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/xtasy-l...
Music promoted by Audio Library • Xtasy - Lucjo (No Copy...
Like us on Facebook :
/ tech-at-home-220885266...
Follow us on Instagram : / tech_at_home
![Roborace Robot using Arduino and BTS7960 | Wireless Robot with Flysky fsi6 [without Brushed ESC]](http://i.ytimg.com/vi/EnbkdrYQ0NE/mqdefault.jpg)
is two escs are enough for rc racing competition?
what happen if we are using 4escs for each motors?
is two escs are enough for rc racing competition?
what happen if we are using 4escs for each motors?
How much load does it carry if we put load on car??
Hlo
Best way to explain and to provide details in Description ........
Thank you
How to blind transmitter to receiver
Please makeing vide on esp32 wifi communication robot and remote
Can u provide me the connection of ESC with motor and receiver
1) connect two right motors in parallel ,and connect them to ESC 1.
2). Connect the ESC 1 to channel 1 of receiver.[all 3 wires : signal,5v,gnd].
3) connect two left motors in parallel ,and connect them to ESC 2.
4). Connect the ESC 2 to channel 2 of receiver.[only signal wire].
5).In the transmitter, go to setup, Elevon,Turn on the mix.
6).If the Motor is rotating in opposite direction, change the Motor terminals.
@@techathome thankiu brother
What about the mixing
In the transmitter, go to setup.
Go to Elevon and switch on that.
What if I use only one Brushed ESC?
You can't turn right and left,
So if i use 2esc then i will be able to forward, reverse and break also..right?
Yes, one ESC for right Motors, and another for Left Motors
Can this esc also work for 12volt dc gear motor with 300rpm torque?
Yes it will work
❤❤
Connection kese kare kisake bad khya jode usaki thodi information jodate samay bata
And were to connect the 1st and 2nd esc
Can u tell me the wire diagram
Bhai jo tune esc and receiver Ko connect karanewali wire ke connection samaj me nahi aye
Ho sake to 1naya video Bana aur upload kar
Plz make a video, how to use bts motor driver without micro controler and brushed esc...
Without microcontroller I don't think its possible. It is required to read the receiver data and actuate the motor driver.
ua-cam.com/video/EnbkdrYQ0NE/v-deo.html
can you please tell how did you program your transmitter sir
Refer this video : ua-cam.com/video/CspzSkydxFA/v-deo.html
(at 4.41)
Thank you sir , sir I like your videos very much I subscribed to your channel.
Thank you for your efforts sir
Sir so if I did the same connections so will this work or do I have to do any setting in the transmitter
Sir I am making a battle bot
Chasis size?
Complete Bot fix inside (30*30) square.
Tell me about your motor ?
A grade Johnson motor 500 RPM
@@techathomegive link pls
Can you please make video on how to use this flysky transmitter on RC bot, RC boat.
ua-cam.com/video/2CPwLNmqmZw/v-deo.html
bro the channels are not connecting
is there any changes should idone to combine the two channels in rc
Yes , to mix you have to do settings
You can refer to this tutorial : ua-cam.com/video/7E34KHna-nI/v-deo.html
@@techathome thank you so much brother
Welcome
How much run time will you get??
It depends on battery mah you use.I think it runs more than 1 hour(not tested exactly)
What is the remote setting to drive 4 wheel , can you share that please
In the transmitter, go to setup.
Go to Elevon and switch on that.
@@techathome thanks, please provide me your email id , so that if required I can take help from you
deepakhd20@gmail.com
How much cost came to build this bot RS. ??
This I have done 3 years back, so now price will be completely different,
when I did,.....
( 4 ) * Johnson gear Motor A grade : 1600
(2) * Brushed ESCs ( I have purchased from bangood ) : 2200
Flysky Fs-i6 Tx and Rx : 3200
(4)* Wheels : 360
2200 mAh 3s lipo battery : 1000
You can give for me this car
No bro, we need this to compete in Robotics competitions
Now bangood also not shipping to India
In Amazon the ESC'S are very costly
It will be very difficult for me to get Components
Sir give me only esc please
Sir, what your motor driver type?
We have used Brushed ESC
Reference: ua-cam.com/video/u0QOf-uMD3U/v-deo.html
Motor rpm
Johnson motor A grade, 500 RPM, 12v
Buddy can we use this one esc to run 750watt(~65 amps) dc brushed motor??
Plzz do repli brother. It will be very much helpful
😊
No bro, it is for small Motor of 1A, 2Amp
Hi just wanted to ask that, can we use other brushed 30A esc apart from this type of specific esc, other that comes with brake on and off button which is quite smaller in size compared to this one...
Kindly reply if you see my massage...
Can you please share a link of product