I do not know if you managed to find a solution. I had same problem and finally managed to have brainpower brushless motor with throttle and s866 display. Using it to spin a hovercraft wheel and for power having the hovercraft salvaged battery too. I have connected the throttle to the 3 wires of the motor colored red black and white, where the white connects to the signal wire of the throttle. Using crocodile wires to put it together. I don’t know how to attach image to show you. Sounds like you used the accelerate wires (red black blue) instead of the throttle wires (red black white) for this controller. I was stuck previously with the display settings always getting PAS, but saw on your vid you had managed to get THL so that helped me fix my setup. Hope the wires will fix yours.
You should be looking in the P-settings and there yóú'll find the right way how to use your throttle. My question is... Because I can't find a good clear simple wiring diagram for how I should connect the wires from my S_866 lcd display to my throttle and then to my controller !!! Bút yóú'vé already made the connection só please please help me out with this problem.... Because this is my first project with a e-bike and I dón't wánt to scréw this up.....‼️‼️ Íf yóú knów whát I méán... Só please brother can you pléásé..., Pléásé sénd me the pictures or email how to connect the wires from my display to my throttle and motor controller. I thínk I knów the red/black wires they need to be connected with the wires from the battery....?? (I hope I got that right....) Greetings from fg from the Netherlands
My friend you forgot to use your throttle. First you connect the learning wire (while the wheel spin use the throttle to save the program and thats the time you disconnect the wire. And you will see your throttle works. I have desame issue before i watch you utube to figure out how to solve but could not find how to fix but i figure out by my self. My ebike works now
Check if you have 5volts on the Red wire and a return voltages to the controler on the Green wire looks like your missing your volts
Connect learning wire and use your throttle to save the program and disconnect the learning wire and you will see your throttle works.
I do not know if you managed to find a solution. I had same problem and finally managed to have brainpower brushless motor with throttle and s866 display.
Using it to spin a hovercraft wheel and for power having the hovercraft salvaged battery too.
I have connected the throttle to the 3 wires of the motor colored red black and white, where the white connects to the signal wire of the throttle.
Using crocodile wires to put it together.
I don’t know how to attach image to show you.
Sounds like you used the accelerate wires (red black blue) instead of the throttle wires (red black white) for this controller.
I was stuck previously with the display settings always getting PAS, but saw on your vid you had managed to get THL so that helped me fix my setup. Hope the wires will fix yours.
@DimitraRetsina-w8f I appreciate you so much for this!!! I'll take your advice and give this another go tomorrow!!!
Jump the blue and red.
Meaning short circuit it
Set the controller back to factory
You should be looking in the P-settings and there yóú'll find the right way how to use your throttle.
My question is...
Because I can't find a good clear simple wiring diagram for how I should connect the wires from my S_866 lcd display to my throttle and then to my controller !!!
Bút yóú'vé already made the connection só please please help me out with this problem....
Because this is my first project with a e-bike and I dón't wánt to scréw this up.....‼️‼️
Íf yóú knów whát I méán...
Só please brother can you pléásé..., Pléásé sénd me the pictures or email how to connect the wires from my display to my throttle and motor controller. I thínk I knów the red/black wires they need to be connected with the wires from the battery....??
(I hope I got that right....)
Greetings from fg from the Netherlands
I'm going to give this another go tomorrow and provide an update.
My friend you forgot to use your throttle. First you connect the learning wire (while the wheel spin use the throttle to save the program and thats the time you disconnect the wire. And you will see your throttle works. I have desame issue before i watch you utube to figure out how to solve but could not find how to fix but i figure out by my self. My ebike works now
@@jovenjarata-ex2oi can I put a video up how two do this