You can also put a spent round in the chamber to dry fire it and just leave the spent round in the chamber until you are ready to shoot again. Put the spent round in the extractor to hold it and slowly guide it into the chamber (rather than into the chamber first) so the extractor doesn't slam the shell and cause extractor wear. Slowly let the slide close with the shell held by the extractor.
Great vid. To dry fire a 22 you can use size 8 plastic drywall anchors. They fit right in the chamber and take the blow from the firing pin well. Most of my 22s will even eject them with the extractor just fine
I see some people below commenting that the thing that holds the spring in place is an E clip - I think that is correct as I have used them in other places and called them an E clip. C Clips usually are larger and hac holes in the endd for C clip pliers to grip them - but your video is very very good - thank you for posting it!
I appreciate your efforts in educating Buckmark owners with good information. That said, I differ with you on everything except how you put the slide back on. We do that the same. First off, I can't imagine how you find slot head screws easier to use than the stock Allen screws. The size is 7/64 and easily available. You won't be constantly slipping off the head as you were. Another thing is you didn't show or talk about he special lock washers that are used on those screws. They can get lost easily so be careful when taking the screws out. There are many ways to remove the slide once the rail is removed and I have no problem with your method. I do it a little different but that is an easy one for everybody and they will gravitate to what suites them. I'm trying to figure out why you removed the slide return spring. It has zero to do with the firing pin and isn't in the way of removing the firing pin whatsoever. Concerning dry firing. Someone posted on here that you can dry fire a newer model. I bought mine this year and put a mark on my breach first time firing when I had a fail to load issue and accidentally dry fired mine. I was indeed pissed that this had happened at no fault of mine. There are many .22 autos on the market that can be dry fired like the Ruger's and the reason is they have a positive firing pin stop. First time I took my Buckmark apart, I realized that it has a firing pin stop. It just isn't utilized to stop the pin in a condition that would allow dry firing. The firing pin only needs to extend to near flush with the breach face of the slide. I pulled my pin out, removed the spring and put it back in with the retaining pin in place and pushed all the way in with a probe and measured how much needed to come off the end of the pin. It was only a few thousandths of an inch and easily stoned off with a 600 grit stone. I shortened until the pin is a couple of thousandths short of the slide face when fully depressed into the firing pin hole. I then put the spring back in and be sure to orient the pin in the right position. You want the pin striking face to be in the center of the cavity where the round will set when loaded. Once this is done, you can dry fire a Buckmark until the cows come home with no adverse effect on the barrel breach face. I have done many friends' Buckmarks this way and all work perfectly. I know this has been lengthy but I hope this will shed another light onto you video. Another thing that is very helpful with the slide spring is that the "C" clip is very easy to lose as stock. I have never seen a need to remove the spring and rod and I have fired thousands of rounds through mine. First time apart is a good time to pull that spring back a little and using your needle nose pliers, just close that clip up better to the groove. The clip they use is really a poor fit for that particular size shaft and groove, but once closed in tight, it will never come apart unless you want to do so. I truly don't mean to be critical of your video but I felt like some further explanation might help those who watch the video then read this post. Really just trying to help.
Very helpful video for Buck Mark owners. I lost my c-clip once and found out that Ace Hardware stocks them and they are 1/8in. size. I think I bought 10 for about a dollar.
Nice vid - in fact well done son. Tip - MWG has the entire recoil system, including the firing pin for $15.00. Buying the assembly saves a lot of money and is a good idea since most are "wear" parts. Just ordered one since mine has seen well over 5,000 round in its life and the plastic parts/firing pin show wear and are getting to end of life. Once again - very well done, including good instruction as to what you are doing throughout. Semper Fi
Great video. It’s never good to dry fire a handgun. However, like a dumbass, when I bought my Buckmark I dry fired it a few times, which caused the entire slide mechanism to lock up. It would also lock up a few times on the range. Never had a gun do that. I ended up buying a halo ring from Tandemkross to use to unlock the slide, and that was before I found out that you cannot dry fire a Buckmark. I’ll watch your video a few times before I attempt to clean the firing pin. Well done.
Hi. Great informative video. I lost my c clamp so I had to purchase a few plus some other parts that will wear out eventually as I have 2 buckmark pistols. What i do do avoid dry fires is I purchased a bunch of .22LR snap caps so it would stay in cocked position or dry fire. I then just leave them in each .22 pistol or rifle. Just subed & Liked. Sincerely, JAMES.
As far a dry firing goes, I just bought a NEW Buck Mark (December 2017) and there is a card in plain sight in the box that tells you NOT to dry fire the gun. I noticed some remarks saying you could dry fire the new ones.
Thanks for the video.. Just purchased a used Buckmark 22 (mfg in 1985) and picked it up last night. Went to the gun range and immediately misfired on 40-50% of the rounds...Looking at the cartridge rims of the rounds that failed I see the strike looks very light...Will take a crack at this tomorrow...The gun is accurate has all "get out" ...I've already ordered new trigger, spring, recoil spring assembly, and a couple other related parts incase I elect to just replace the firing pin..Thanks
I lost the c clamp while I was disassembling the Buckmark. Didn’t know it at the time so I reassembled the pistol without it. Don’t know how I got it together again, it wasn’t easy, shoots fine though. Just ordered c clamps off eBay so I can assemble it correctly next time.
The spring on the firing pin hold the pin back so you don’t get slam fires. If the spring on the firing pin goes bad it would cause slam fires not soft strike miss fires.
@@ironhorse127 It belonged to my girlfriends brother. He let her borrow it to qualify. Very dirty. I lost dang spring so had to order that and front sight fiber optic! I gave it back super clean/improved. Those C clamps are TINY.
1. Great vid I was totally having this issue and didn't know how to get the firing pin out and didn't want to break anything. 2. @13:30 "I don't even know if that's what it is called, if not that's what its called here." (Hilarious). It's a C-Clip everywhere else. A C-Clamp is C shaped Clamp that can be used to press the Piston back in on your Disk Brake Caliper (much larger).
Using quite some second hand .22lr, and having sometimes misfires, I do also go further than a field strip. It is always the same thing: gunk at the inside housing. Of a bolt action rifle or a blow back pistol, same issue. Previous owners always sprayed inside their guns. I do use ear butts and tooth picks to clean inside. And/or ultra sonic device. Never had to replace a firing pin yet. Side note about gunk: if you get a second hand bolt action rifle and it cocks with difficulty, check the blind holes (1 or 2) next to the chamber. Where the extractor fits in. Ow, ow,ow. Get a tooth pick and be surprised how much gunk comes out of it. Oil mixed with carbon and lead. After cleaning you can close the bolt with 1 finger. May this be an answer on the question “why no lubrification?”
I own a Buck Mark and love shooting it. But I was taught to never run any cleaning too down the barrel from the muzzle of the gun. Browning says not to disassemble this gun to clean it. That's DUMB! You can not clean this gun properly without removing the barrel! Come on BROWNING!
Titanium Firing Pin for Browning® Buck Mark at Tandom cross, lighter and 30% stronger if you tear it down might as well replace it...still good vid bro
Snap Caps and a minimal amount of lube will reduce the carbon and gunk. And all do not dry fire so you don't need to watch videos like this. As well with the 2 screws, are there crown type washers between screws and sight strap?
Like your fiance's buckmark she a pre 2001 version, The slide is different the guide rod assy is different. Browning has replacements you can get for $45.75. Includes a new slide and guide rod assy. Will need to take the extractor out of the old and into the new slide.
did you mean that if im pointing the gun at a target, the flat side of the firing pin would be on the right side of my gun, im still confused, please help thanks
No they are all plastic.....if you want the internals all of steel get a pre 2001....Browning cheapened the internals when they updated the pistol after 2001.....
I just stripped down my buckmark, and didn't find any C clamp, so the spring was able to move freely about the rod it was coiled around. Is this a big problem? Recently it has been jamming a bunch (the bullet hits the area above the chamber), do you think its because I dont have a C clamp? If so, where can I get one online?
happymark1805 I don't blame him. Lube only collects grime, like a magnet. I only like lube on things that are away from the firing area(where all the gunk is). .22 is a very nasty cartridge. Don't do things that help collect that stuff. Just my opinion...
I thought the ruger 22/45 was a PITA.. even on the Ruger you need no tools for field strip! .how can they justify charging $450 for a buckmark and you can pick up the Ruger for $300? Is it just a whole lot more accurate?
Not enough detail in your video work and it’s too busy in the background. Your handgun covers every corner on the screen. Your bast bet would to pull the video and stat over again and I’m sure you can do a better job Nice attempt of Video work
Before you start working on the gun, you really should tell your viewers to make sure the gun is unloaded, open the breach and show that to the viewers.
Enjoyed You are one of the very few people on u tube that knows the difference between a bolt return spring with guide rod and a firning.Well done
You can also put a spent round in the chamber to dry fire it and just leave the spent round in the chamber until you are ready to shoot again. Put the spent round in the extractor to hold it and slowly guide it into the chamber (rather than into the chamber first) so the extractor doesn't slam the shell and cause extractor wear. Slowly let the slide close with the shell held by the extractor.
Great vid. To dry fire a 22 you can use size 8 plastic drywall anchors. They fit right in the chamber and take the blow from the firing pin well. Most of my 22s will even eject them with the extractor just fine
Wow thanks for the great tip!
I use them all the time. They truly work
The complete firing pin assembly can be purchased from many online firearms sites, it is easy to replace, inexpensive and good to keep as a spare.
I see some people below commenting that the thing that holds the spring in place is an E clip - I think that is correct as I have used them in other places and called them an E clip. C Clips usually are larger and hac holes in the endd for C clip pliers to grip them - but your video is very very good - thank you for posting it!
I know this is old but you are referring to a snap ring
@@johnnunnelee5741 pretty much the same thing
I appreciate your efforts in educating Buckmark owners with good information. That said, I differ with you on everything except how you put the slide back on. We do that the same. First off, I can't imagine how you find slot head screws easier to use than the stock Allen screws. The size is 7/64 and easily available. You won't be constantly slipping off the head as you were. Another thing is you didn't show or talk about he special lock washers that are used on those screws. They can get lost easily so be careful when taking the screws out. There are many ways to remove the slide once the rail is removed and I have no problem with your method. I do it a little different but that is an easy one for everybody and they will gravitate to what suites them. I'm trying to figure out why you removed the slide return spring. It has zero to do with the firing pin and isn't in the way of removing the firing pin whatsoever. Concerning dry firing. Someone posted on here that you can dry fire a newer model. I bought mine this year and put a mark on my breach first time firing when I had a fail to load issue and accidentally dry fired mine. I was indeed pissed that this had happened at no fault of mine. There are many .22 autos on the market that can be dry fired like the Ruger's and the reason is they have a positive firing pin stop. First time I took my Buckmark apart, I realized that it has a firing pin stop. It just isn't utilized to stop the pin in a condition that would allow dry firing. The firing pin only needs to extend to near flush with the breach face of the slide. I pulled my pin out, removed the spring and put it back in with the retaining pin in place and pushed all the way in with a probe and measured how much needed to come off the end of the pin. It was only a few thousandths of an inch and easily stoned off with a 600 grit stone. I shortened until the pin is a couple of thousandths short of the slide face when fully depressed into the firing pin hole. I then put the spring back in and be sure to orient the pin in the right position. You want the pin striking face to be in the center of the cavity where the round will set when loaded. Once this is done, you can dry fire a Buckmark until the cows come home with no adverse effect on the barrel breach face. I have done many friends' Buckmarks this way and all work perfectly. I know this has been lengthy but I hope this will shed another light onto you video. Another thing that is very helpful with the slide spring is that the "C" clip is very easy to lose as stock. I have never seen a need to remove the spring and rod and I have fired thousands of rounds through mine. First time apart is a good time to pull that spring back a little and using your needle nose pliers, just close that clip up better to the groove. The clip they use is really a poor fit for that particular size shaft and groove, but once closed in tight, it will never come apart unless you want to do so. I truly don't mean to be critical of your video but I felt like some further explanation might help those who watch the video then read this post. Really just trying to help.
Its a e clip damnit thank you all for your efforts and knowledge.
Very helpful video for Buck Mark owners. I lost my c-clip once and found out that Ace Hardware stocks them and they are 1/8in. size. I think I bought 10 for about a dollar.
Nice vid - in fact well done son. Tip - MWG has the entire recoil system, including the firing pin for $15.00. Buying the assembly saves a lot of money and is a good idea since most are "wear" parts. Just ordered one since mine has seen well over 5,000 round in its life and the plastic parts/firing pin show wear and are getting to end of life.
Once again - very well done, including good instruction as to what you are doing throughout.
Semper Fi
I can't find the firing pin recoil assembly on MWG. Got a link?
fishrecon I
Called an e-clip measure the opening at the internal ears and thickness to get from a hardware supply like McMaster-Carr.
Great video. It’s never good to dry fire a handgun. However, like a dumbass, when I bought my Buckmark I dry fired it a few times, which caused the entire slide mechanism to lock up. It would also lock up a few times on the range. Never had a gun do that. I ended up buying a halo ring from Tandemkross to use to unlock the slide, and that was before I found out that you cannot dry fire a Buckmark. I’ll watch your video a few times before I attempt to clean the firing pin. Well done.
Hi. Great informative video. I lost my c clamp so I had to purchase a few plus some other parts that will wear out eventually as I have 2 buckmark pistols. What i do do avoid dry fires is I purchased a bunch of .22LR snap caps so it would stay in cocked position or dry fire. I then just leave them in each .22 pistol or rifle. Just subed & Liked. Sincerely, JAMES.
As far a dry firing goes, I just bought a NEW Buck Mark (December 2017) and there is a card in plain sight in the box that tells you NOT to dry fire the gun. I noticed some remarks saying you could dry fire the new ones.
And just to re-affirm this above factual comment... I have a new Buckmark in 2022, and it is still not to be dry-fired.
Thanks for the video.. Just purchased a used Buckmark 22 (mfg in 1985) and picked it up last night. Went to the gun range and immediately misfired on 40-50% of the rounds...Looking at the cartridge rims of the rounds that failed I see the strike looks very light...Will take a crack at this tomorrow...The gun is accurate has all "get out" ...I've already ordered new trigger, spring, recoil spring assembly, and a couple other related parts incase I elect to just replace the firing pin..Thanks
I do appreciate the video. I was having the same problem and after cleaning it fired just fine.
I lost the c clamp while I was disassembling the Buckmark. Didn’t know it at the time so I reassembled the pistol without it. Don’t know how I got it together again, it wasn’t easy, shoots fine though. Just ordered c clamps off eBay so I can assemble it correctly next time.
Great vid! How'd you get everything to stick to the wall?
It's actually a work bench. I printed the logos, layed them out, then placed some plexiglass over it and screwed it down so it would stay in place.
@@WHMarms I thot it was either magic or magnetism! :)
The spring on the firing pin hold the pin back so you don’t get slam fires. If the spring on the firing pin goes bad it would cause slam fires not soft strike miss fires.
Mine was missing the guide rod C-clamp. Thanks for pointing it out. Ordering one.
Mine was too. Im waiting for 2 new one from Numrich right now.
@@ironhorse127 It belonged to my girlfriends brother. He let her borrow it to qualify. Very dirty. I lost dang spring so had to order that and front sight fiber optic! I gave it back super clean/improved. Those C clamps are TINY.
1. Great vid I was totally having this issue and didn't know how to get the firing pin out and didn't want to break anything. 2. @13:30 "I don't even know if that's what it is called, if not that's what its called here." (Hilarious). It's a C-Clip everywhere else. A C-Clamp is C shaped Clamp that can be used to press the Piston back in on your Disk Brake Caliper (much larger).
Using quite some second hand .22lr, and having sometimes misfires, I do also go further than a field strip. It is always the same thing: gunk at the inside housing. Of a bolt action rifle or a blow back pistol, same issue. Previous owners always sprayed inside their guns. I do use ear butts and tooth picks to clean inside. And/or ultra sonic device. Never had to replace a firing pin yet.
Side note about gunk: if you get a second hand bolt action rifle and it cocks with difficulty, check the blind holes (1 or 2) next to the chamber. Where the extractor fits in. Ow, ow,ow. Get a tooth pick and be surprised how much gunk comes out of it. Oil mixed with carbon and lead. After cleaning you can close the bolt with 1 finger.
May this be an answer on the question “why no lubrification?”
I own a Buck Mark and love shooting it. But I was taught to never run any cleaning too down the barrel from the muzzle of the gun. Browning says not to disassemble this gun to clean it. That's DUMB! You can not clean this gun properly without removing the barrel! Come on BROWNING!
Titanium Firing Pin for Browning® Buck Mark at Tandom cross, lighter and 30% stronger if you tear it down might as well replace it...still good vid bro
on mine i always use a spent case . load the spent case being careful not to have it strike in the same place.
Thanks. My buck mark is particular about ammo . What kind do you think runs best? Thanks
Snap Caps and a minimal amount of lube will reduce the carbon and gunk. And all do not dry fire so you don't need to watch videos like this. As well with the 2 screws, are there crown type washers between screws and sight strap?
Thanks for the video! What are the recommended parts to lubricate after cleaning the buckmark?
Maybe I’m missing something. Why disassemble the recoil spring to remove the firing pin?
Not necessary.....you can remove the firing fin without removing the recoil spring.....
6:20 hah ha its called a Jesus Clip. Cause when it goes flying off to outer space, you can only yell jesus christ!!
I think evry one takes the spring out 1rst b4 u take the slide off seems easer thumbs up great instruction
Just to complicate things the C clip may also be called a circlip.
What size and length are the sight screws? Where did you get them?Mine have allen head screws and i would like to replace them.Thanks
I cleaned my fiancé's Buckman today, it's an older one, I notice that the insides on hers is different than yours
Like your fiance's buckmark she a pre 2001 version, The slide is different the guide rod assy is different. Browning has replacements you can get for $45.75. Includes a new slide and guide rod assy. Will need to take the extractor out of the old and into the new slide.
did you mean that if im pointing the gun at a target, the flat side of the firing pin would be on the right side of my gun, im still confused, please help thanks
I cant see the pistol ....the chick in the water with the AR has my full attention!😂
Midway has discontinued their firing pins, they are hard to come by, I have the old style, can't seem to find any
E-bay has everything you need for this pistol.
Is there any aftermarket firing pin housing that's made of steel? Cleaned mine today and was wondering that at the time.
Not that I am aware of sorry :(
No problem. There probably isn't. I've done my checking and that's now my conclusion. Thanks for the reply.
No they are all plastic.....if you want the internals all of steel get a pre 2001....Browning cheapened the internals when they updated the pistol after 2001.....
I just remove the slide with everything still intact, toss the whole thing into the ultrasonic cleaner and *bam* - super clean, no more light strikes.
I just stripped down my buckmark, and didn't find any C clamp, so the spring was able to move freely about the rod it was coiled around. Is this a big problem? Recently it has been jamming a bunch (the bullet hits the area above the chamber), do you think its because I dont have a C clamp? If so, where can I get one online?
I didnt have the c clamp either, did you figure something out? How bas could it be etc?
Thanks for this! I'll be getting a Buckmark soon and really appreciate the info.
you clean it but do not lube it ??
happymark1805 I don't blame him. Lube only collects grime, like a magnet. I only like lube on things that are away from the firing area(where all the gunk is). .22 is a very nasty cartridge. Don't do things that help collect that stuff. Just my opinion...
I thought the ruger 22/45 was a PITA.. even on the Ruger you need no tools for field strip! .how can they justify charging $450 for a buckmark and you can pick up the Ruger for $300? Is it just a whole lot more accurate?
I have shot both, but purchased the buckmark. Accuracy wise they are pretty similar, but I tend to shoot better with the buckmark.
Shoot both, & buy the buckmark, it's not the least bit fussy about ammo dependability like the Ruger is.
my slide keeps getting stuck where I can't pull it back. Any ideas? Thanks.
Mine did the same, a plastic piece on the end of the recoil was broke and jamming
Thanks much for the detailed/informative video. 2 thumbs up!
We want more mosin Miller!
Thanks
Dry firing a Buckmark is not a problem if it is a new one.
I purchased one in 2019 and it said in the paperwork not to dry fire.
Mosin Miller is a deadbeat we try to keep him off the show as much as possible.
Not enough detail in your video work and it’s too busy in the background. Your handgun covers every corner on the screen. Your bast bet would to pull the video and stat over again and I’m sure you can do a better job Nice attempt of Video work
Agree. Good info in the video, but redo it and take a Valium before you start.
Before you start working on the gun, you really should tell your viewers to make sure the gun is unloaded, open the breach and show that to the viewers.
Why?
Disgusting? What word do you use for rotting fish or roadkill on a 90 degree day if carbon build up in a firearm is "disgusting"?