There is one basic thing that you left out. I have been an IT consultant for 25 years, and I recently took an old Smart UPS 1500 out of my closet. Frankly, I did not remember whether it worked, or not, when I stored it. It would not turn on at all, and I went through all your steps (most, of which I knew). Well, I took one last step: I had a second, working, Smart UPS 1500, and I swapped the battery, and sure enough, it worked. It was not dead, just the battery was totally done. A totally dead battery is also enough to cause this issue.
Anyway around this? I have 2 1500 RMs that I put in storage but want to use. Neither will power on. I dont want to buy new batteries just to find out theyre broken
Good morning, I replaced the batteries in a APC SMT 3000 XLA UPS system. However, the battery date will not change, I set it but it reverts back to previous set date. What can I do to correct this issue?
Hi Jon, My issue is a little different. I recently purchased a good used APC C 1500 UPS and it sat for maybe two months before I got to use it. It has the LCD display. After installing it, I connected power supply lead to main power then plugged one load cable to surveillance unit. I wanted UPS to my CCTV system in case of a black out. After pressing the power on button on UPS, the battery charge indicates very low battery due to it having sat around for a while, the batteries have discharged. What happens after a short time, after having line voltage, the UPS will drop the output voltage then switch off. Why would it turn off if it's connected to mains power. It should be charging the batteries AND be able to provide output to power external device right ? The Battery back up is only there in case of a power outage, but there is no outage as such as it's connected to mains power. Would a bad battery pack be messing with the electronics and is shutting the whole unit as a form of protection ? I hope you can share some knowledge here please. Thank you.
Ants went inside my UPS LBPro 1000. It started fluctuating. Asked for technician.. Is there anything I can make the ants to stop going inside??.. please help
The last time my ups was working, it was fully charged, and I've tried everything here and still nothing. I fully reconnected the battery. I was moving my ups, so I took out the battery disconnect and when I put it back in it seemed intermittent, so I pulled it out and put it back in got a big spark and it never came back on. What happened?
wMediaOnline hehe.. big spark huh Probably Blown a Capacitor or 2 Now. Unless you have electrical training, you SHOULD NOT attempt to replace them yourself but to answer your question it's Most likely Blown components if it did work, and now it's not working it means IN THE CIRCUIT BOARD there is a point at which the Electricity stops flowing because a part is damaged, this will usually occur because of an Over current situation in which case usually Fuses are what blow or Capacitors, beyond that you generally find Resistors and diodes are faulty and just because a Capacitor is not blown does not mean it is not faulty Most techs think that the way to check a capacitor is to get out a Multimeter and go to Capacitance setting. THIS IS NOT CORRECT (this is one small way, but not very reliable way to check) and ESR tester is required if one wants to check if a capacitor is good or bad. RELIABLY. I say get an electrician to look at it or ask the company how much they charge for a new unit or how much for a new Mainboard to be replaced You'll probably find that THE COMPANY that manufacturs it will make the cost of replacing the board more expensive than the Unit itself an electrician could (Depending on the issue) have a replacement cost of $1 - $50 (more realistically,.... approx $10) he would also want to charge for labour and time, so let's say $100 per hour for that, and you might be looking at $150 - $200 to get it fixed vs the cost of a new unit Unless you have a friend how is an electrician or Engineer in which case you'll fix it for under $50 hope that helps
emmanuel alornyo Please fill out this help form and one of our technicians will help troubleshoot your issue: coasttec.com/support/contact-our-support/
I have a Dell Tower UPS 1000W External Battery Module, but it does not turn on, if the batteries are dead, it does not turn on, or even if the battery is dead it turns on
Babar Khalid depends on the UPS, but it should turn on Fundamentally Uninterruptable Power Supplies work like this (Over simplified explanation)....... there are 2 sides to it the side that takes in Power from your wall the side that stores the power in case a black out happens so... While you have power coming in from the side that takes it from the wall point (simply stated) 2 things happen. 1. it supplies your devices / servers / computers /whatever with power 2. it fills up the batteries (Charges them, if you will) Point being (As you know) when a power outtage happens, there is a RELAY (Switch) inside that detects no current of Voltage coming in and it switches to BATTERY POWER When Voltage and Current is detected again.... IT SWITCHES BACK and refills the part that was used in the battery. so.... IF YOU DISCONNECT THE BATTERIES or IF THEY ARE DEAD all that SHOULD happen is this it should work as normal, EXCEPT if you have a power outtage it won't keep your devices on (Because the batteries are not charged) so your answer is... YES , it should still switch on but without the batteries working THE UPS IS JUST A GLORIFIED POWER POINT or POWER BOARD Hope that helps
"SC, SU, and SUA Smart-UPS require a functional battery be connected in order to turn on. If the battery is disconnected, or failed and completely drained, the UPS will not turn on. SMX and SMT series Smart-UPS do not have this limitation." from APC website
If nothing of that sort works, can the circuits or something inside of the UPS be dead or just as simple as dead batteries? It is 12v batteries, right?
There is one basic thing that you left out. I have been an IT consultant for 25 years, and I recently took an old Smart UPS 1500 out of my closet. Frankly, I did not remember whether it worked, or not, when I stored it. It would not turn on at all, and I went through all your steps (most, of which I knew). Well, I took one last step: I had a second, working, Smart UPS 1500, and I swapped the battery, and sure enough, it worked. It was not dead, just the battery was totally done.
A totally dead battery is also enough to cause this issue.
Anyway around this? I have 2 1500 RMs that I put in storage but want to use. Neither will power on. I dont want to buy new batteries just to find out theyre broken
Thank you for this! My DC disconnect popped out or was loose (it looked like it was still plugged in) and connecting it again fixed it!
Good morning, I replaced the batteries in a APC SMT 3000 XLA UPS system. However, the battery date will not change, I set it but it reverts back to previous set date. What can I do to correct this issue?
Hi Jon, My issue is a little different.
I recently purchased a good used APC C 1500 UPS and it sat for maybe two months before I got to use it. It has the LCD display.
After installing it, I connected power supply lead to main power then plugged one load cable to surveillance unit. I wanted UPS to my CCTV system in case of a black out.
After pressing the power on button on UPS, the battery charge indicates very low battery due to it having sat around for a while, the batteries have discharged.
What happens after a short time, after having line voltage, the UPS will drop the output voltage then switch off.
Why would it turn off if it's connected to mains power. It should be charging the batteries AND be able to provide output to power external device right ?
The Battery back up is only there in case of a power outage, but there is no outage as such as it's connected to mains power.
Would a bad battery pack be messing with the electronics and is shutting the whole unit as a form of protection ?
I hope you can share some knowledge here please.
Thank you.
THANKS. This finally helped!
You didn't mention the fuse between the batteries. That could kill the DC side too. What is the amperage of the fuse on this model?
Hi i have the 2200xl 120 vdc, but the display face flat cable got damaged! and the power and test buttons r missing, is there a fix for it?
Great video! liked and subscribed.
My 1000 unit doesn't have input pwr lights indicator on the bac of unit. I'm assuming the pwr transistor failure. Any schematics?
What if d battery is not powering up the ups?
Is there a fuse inside the unit that could go out?
Ants went inside my UPS LBPro 1000. It started fluctuating. Asked for technician.. Is there anything I can make the ants to stop going inside??.. please help
Hi my ups doesn't pass the POST. Where can i check first
Mine is charging well but not power on the outlet(s) when unplug the unit ( battery charged) when plugged in have power on the outlet(s)
Hi
I have APC Smart-UPS RT 5000 and it won't turn on>>
please could you help me>>>>
thanks for your kind help
The last time my ups was working, it was fully charged, and I've tried everything here and still nothing. I fully reconnected the battery. I was moving my ups, so I took out the battery disconnect and when I put it back in it seemed intermittent, so I pulled it out and put it back in got a big spark and it never came back on. What happened?
wMediaOnline
hehe.. big spark huh
Probably Blown a Capacitor or 2
Now. Unless you have electrical training, you SHOULD NOT attempt to replace them yourself
but to answer your question
it's Most likely Blown components
if it did work, and now it's not working
it means IN THE CIRCUIT BOARD there is a point at which the Electricity stops flowing because a part is damaged,
this will usually occur because of an Over current situation
in which case usually Fuses are what blow or Capacitors,
beyond that you generally find Resistors and diodes are faulty
and just because a Capacitor is not blown does not mean it is not faulty
Most techs think that the way to check a capacitor is to get out a Multimeter and go to Capacitance setting.
THIS IS NOT CORRECT (this is one small way, but not very reliable way to check)
and ESR tester is required if one wants to check if a capacitor is good or bad. RELIABLY.
I say get an electrician to look at it
or
ask the company how much they charge for a new unit
or how much for a new Mainboard to be replaced
You'll probably find that THE COMPANY that manufacturs it will make the cost of replacing the board more expensive than the Unit itself
an electrician could (Depending on the issue) have a replacement cost of $1 - $50 (more realistically,.... approx $10)
he would also want to charge for labour and time, so let's say $100 per hour for that, and you might be looking at $150 - $200 to get it fixed vs the cost of a new unit
Unless you have a friend how is an electrician or Engineer in which case you'll fix it for under $50
hope that helps
Good real world advice...
What if the breaker reset button doesn't stay in when I press it?
did you figure out?
hello please i do have smart UPS 1500. i have all 6 lights blinking anytime i blug in my ac power. but its runs okay on battery. kindly help me out
emmanuel alornyo Please fill out this help form and one of our technicians will help troubleshoot your issue: coasttec.com/support/contact-our-support/
I have a Dell Tower UPS 1000W External Battery Module, but it does not turn on, if the batteries are dead, it does not turn on, or even if the battery is dead it turns on
Will it turn on if batteries are completely dead?
Babar Khalid
depends on the UPS, but it should turn on
Fundamentally Uninterruptable Power Supplies work like this
(Over simplified explanation).......
there are 2 sides to it
the side that takes in Power from your wall
the side that stores the power in case a black out happens
so... While you have power coming in from the side that takes it from the wall point (simply stated) 2 things happen.
1. it supplies your devices / servers / computers /whatever with power
2. it fills up the batteries (Charges them, if you will)
Point being (As you know) when a power outtage happens, there is a RELAY (Switch) inside that detects no current of Voltage coming in and it switches to BATTERY POWER
When Voltage and Current is detected again.... IT SWITCHES BACK and refills the part that was used in the battery.
so.... IF YOU DISCONNECT THE BATTERIES or IF THEY ARE DEAD
all that SHOULD happen is this
it should work as normal, EXCEPT
if you have a power outtage it won't keep your devices on (Because the batteries are not charged)
so your answer is...
YES , it should still switch on
but without the batteries working
THE UPS IS JUST A GLORIFIED POWER POINT or POWER BOARD
Hope that helps
"SC, SU, and SUA Smart-UPS require a functional battery be connected in order to turn on. If the battery is disconnected, or failed and completely drained, the UPS will not turn on. SMX and SMT series Smart-UPS do not have this limitation." from APC website
mine still not working, tried all , its an forzaups at501
apc ups surt8000xli without battery how utility direct use
APC
UPS Apc the order number and they said they were working
Thanks
If nothing of that sort works, can the circuits or something inside of the UPS be dead or just as simple as dead batteries? It is 12v batteries, right?
I got all the way back to the power plant, I think I have as broken unit
god speed captain hindsight!
i need apc ups rt 8000 xli schematic diagram